Digital Projection Titan Sx+-500 User Manual

Rev B          02/2007        page 4.9
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
The remote control
Layout
Timeout
There is a 10 second timeout for the three Lens adjustment keys (see note on next
page.
There is a separate, adjustable timeout for the On Screen Menus (see Navigating
menus and submenus, in Using the Menus and On Screen Display, in Setup
Menu, later in this section).
Notes
Many features are controlled
from the menus using the menu
navigation keys on the...

Rev B          02/2007         page 4.10
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
Closing the shutter produces a
better black than simply
removing the signal, as the light
source will be completely
blocked by the shutter blade.
When the OSD is OFF:
-  all menu navigation keys are
disabled.
- keys such as 
 BRI
(brightness) will still function,
but the slider bars will not be
visible on screen.
When any of the three Lens
adjustment keys is pressed, the
blue Transmit...

Rev B          02/2007        page 4.11
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Auto-detect input mode
•Press  to force the projector to re-detect the input mode
(see Input modes and settings, earlier in this section).
Source information
•Press  to display the source information screen.
Input
•Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI
4. SDI
5. Composite Video
6. S-Video
7. Component
•Or press the numbered keys 1–7 to...

Rev B          02/2007         page 4.12
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
For more information about
input modes and input presets,
see earlier in this section, Input
modes and settings.
A preset can be applied only to
the same mode for which it was
created. If the detected input
mode does not match, then
settings from the mode history
or mode library will be applied.
For more information about
input modes, see Input modes
and settings. earlier in this...

Rev B          02/2007        page 4.13
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
The red, green and blue keys
are disabled when the OSD is
switched OFF.
The Saturation control is
available for Composite, S-
Video and Component input s
only.
The Phase control is available
for RGB inputs only.
For all adjustment s on this page
that require more than one key
to be pressed:
- after 10 seconds, if no
adjustment has been made,  the
 key must be pressed again
to resume...

Rev B          02/2007         page 4.14
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Notes
The magnify feature utilises a
digital zoom. Used with the p an
control, this can be used to:
- enlarge a section of the image
- enable the use of multiple
projectors to construct a large
image from tiles.
The pan control is available only
when the image has been
magnified.
If the OSD moves off screen
due to a change in image size,
then pressing the size key will
restore its...

Rev B          02/2007        page 4.15
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Notes
Some  menu controls can be
accessed directly using the
control keys (see earlier in this
section).
When the OSD is OFF, all menu
navigation keys will be disabled.
When the OSD is switched
back ON, the menus will remain
OFF until the  
 key is
pressed again. The menus will
then reopen at the same point
they were last viewed.
If a menu is opened, and no
other key is pressed within the...

Rev B          02/2007         page 4.16
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Press  to open the menu. The blue highlight moves to the first item in the
menu, which may be submenu, for example the Projector Setup submenu.
•To select a submenu, press 
 and  , for example the Lamp submenu.
Press 
 to open the submenu. The submenu opens, with the title at the top.
•To close the submenu and return to the previous level, press 
.
•There may be up to three levels of submenu,...

Rev B          02/2007        page 4.17
Digital Projection TITAN sx+-500 User Manual 4. Controlling the projector
Slider bar
The highlighted slider bar shows which
control is active currently.
To adjust the slider press 
 and .
Parameter selection
To select from a number of p arameters,
(shown one at a time to the right),
press 
 and .
These two items are greyed out and
the values are blank, showing that they
are not available, due to the effect of
settings made in other menus, or due
to the type of...

Rev B          02/2007         page 4.18
4. Controlling the projectorDigital Projection TITAN sx+-500 User Manual
Input menu
To return to the main menu, press  up to three times.
From the main menu:
•Press 
 and   until Input is highlighted.
Press 
 to open the Input menu. The blue highlight moves to the first item in
the menu.  The 
 symbol shows which input is currently selected.
Input Source
•Press  and   to select from:
1. RGB1
2. RGB2
3. DVI
4. SDI
5. Composite Video
6. S-Video
7. Component
•Press...