Digital Projection Titan Sx+ 3d, Dual 3d, Titan Sx+ 3d, Dual 3d Ultra Contrast User Manual

Rev C  April 2011 Page 4.41
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Black Level Uplift
As it is not possible for any projector to produce an absolute black, an\
y ‘black’ areas 
in the overlapped edges may appear slightly less dark than those in the \
rest of the 
image.
Black Level Uplift can be used to counteract this effect, by...

Page 4.42 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 To adjust Manually:
  Working on one projector at a 
time, display a test pattern of 
0% Field (black), set all four 
border adjustments to zero, 
then increase the size of each, 
until the border disappears.
Non-Addressable Border
Around the edge of the DMD...

Rev C  April 2011 Page 4.43
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 
Setup Menu 
 Global Colourimetry
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Read these notes on Colour 
and Global Colourimetry 
before making any settings in...

Page 4.44 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Read the notes on Colour and 
Global Colourimetry earlier 
in this section before making 
any settings in the Colour 
menus.
  Note that any changes made in 
the Global Colourimetry menu  
will affect ALL inputs, modes 
and presets for which  Global 
Mode...

Rev C  April 2011 Page 4.45
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Lamp Setup
Press  and   to select Lamp.
 Press  to open the Lamp submenu.
The middle row shows the current lamp setting.
Change Lamp Setting
Press  and   to select Change Lamp Setting.
Press  to open the Lamp Setting control box.
single lamp models
dual lamp...

Page 4.46 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Lamp power
Press  and   to select the Lamp Power setting.
 Press  and   to adjust the Lamp Power from:
  80 to 100%  in 1% steps
Lamp Mode
Press  and   to select Lamp Mode.
 Press  and   to select from:
single lamp modes
Lamp 1
  lamp 1 only
Lamp 2 lamp 2 only...

Rev C  April 2011 Page 4.47
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 
Setup Menu 
 On Screen Display
 The On Screen Display will 
move to the centre of the DMD 
when Blanking is turned On.
  (see Geometry menu, earlier in 
this section).
  If a menu is opened, and no 
other key is pressed within the 
period set in the  OSD...

Page 4.48 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Password
Entry to the password protected area is available to authorised service \
personel 
only.
Press 
 and   to select Password.
 Press  to open the Password control box.
Press  and   to select each digit in turn.
 Press  and   to adjust the digit from:
0 to 9...

Rev C  April 2011 Page 4.49
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 
Setup Menu 
 Comunication
 When fresh batteries are 
inserted in the remote control, 
it will default to address  00. 
Remote control  00 is a master 
control,  able to control all 
projectors.
  If two or more projectors are set 
to the same address, they...

Page 4.50 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 
Setup Menu 
 Network
 Some items may be greyed out 
or not editable, due to the effect 
of other settings made in the 
Network submenu.
  For example, if a Wired 
Connection  is selected:
 Wifi, Channel and SSID will be 
unavailable.
Setup menu continued...