Digital Projection Titan Sx+ 3d, Dual 3d, Titan Sx+ 3d, Dual 3d Ultra Contrast User Manual

Rev C  April 2011 Page 4.11
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
The remote control
Layout
Timeout
There is a 10 second timeout for the three Lens adjustment keys (see no\
te on next 
page).
There is a separate, adjustable timeout for the On Screen Menus (see  On Screen 
Display, in Setup Menu, later in this section).
Notes...

Page 4.12 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Closing the shutter produces 
a better black than simply 
removing the signal, as the 
light source will be completely 
blocked by the shutter blade.
 When the OSD is OFF:
  -  all menu navigation keys are 
disabled.
 - keys such as  BrI 
(brightness) will...

Rev C  April 2011 Page 4.13
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Calibrate Focus
Press  followed by  to calibrate the lens focus mechanism.
Calibrate Zoom
Press  followed by  to calibrate the lens zoom mechanism.
Auto-detect input mode
Press  to force the projector to re-detect the input mode and apply the 
default modal...

Page 4.14 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 For more information about 
input modes and input presets, 
see earlier in this section,  Input 
modes and settings.
  See also Input menu , later in 
this section.
  A preset can be applied only to 
the same mode for which it was 
created. If the detected...

Rev C  April 2011 Page 4.15
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 The Saturation control is 
available for Composite, S-
Video and Component inputs 
only.
  The Phase control is available 
for RGB inputs only.
  The Geometry settings are 
NOT available for Input 8.
  For all adjustments on this page 
that require more...

Page 4.16 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 The magnify feature utilises a 
digital zoom. Used with the pan 
control, this can be used to:
  - enlarge a section of the image
 - enable the use of multiple 
projectors to construct a large 
image from tiles.
 The pan control is available 
only when the...

Rev C  April 2011 Page 4.17
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When the OSD is OFF, all menu 
navigation keys will be disabled.
  When the OSD is switched back 
ON, the menus will remain OFF 
until the  
 key is...

Page 4.18 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Press  to open the menu. The blue highlight moves to the first item in the 
menu, which may be submenu, for example the Projector Setup submenu.
To select a submenu, press 
 and  , for example the Lamp submenu. 
Press 
 to open the submenu. The submenu opens, with...

Rev C  April 2011 Page 4.19
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Slider bar
The highlighted slider bar shows which 
control is active currently.
To adjust the slider press 
 and .
Parameter selection
To select from a number of parameters, 
(shown one at a time to the right), 
press 
 and .
These two items are greyed out and...

Page 4.20 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Input menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Input is highlighted.
Press  to open the Input menu. The blue highlight moves to the first item in 
the menu. The  symbol shows which input is currently...