Digital Projection Titan Sx+ 3d, Dual 3d, Titan Sx+ 3d, Dual 3d Ultra Contrast User Manual

Rev C  April 2011 Page 4.51
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 IP Address cannot be changed 
if DHCP is set to ON.
 DHCP will set the the address, 
which will be displayed for 
information only.
Setup menu, Network continued
DHCp
Press  and   to select DHCP
 Press  to open the DHCP control box.
 Press  and   to select...

Page 4.52 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 IP Subnet cannot be changed if 
DHCP is set to ON.
  DHCP will set the the subnet 
mask, which will be displayed 
for information only.
Subnet Mask
Press  and   to select Subnet
 Press  to open the Subnet control box.
 Press  and   to select from:
Automatic...

Rev C  April 2011 Page 4.53
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Gateway Mask
Press  and   to select Gateway
Press 
 to open the IP Address control box.
Use 
 and   to select each number in turn.
Use  and   to adjust the number
then move to the next number.
Use 
 and   to select from
Apply
  Press   to apply the new IP...

Page 4.54 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 3D may not be present on some 
models
 
Setup Menu  
 3D
 If FastFrame  is turned on, then 
setting 3D Mode to Consumer 
or Professional will turn it off.
  When 3D Enable is on, it is not 
possible to turn on  FastFrame.
 It is important that 3D Input...

Rev C  April 2011 Page 4.55
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
3D Format
Press  and   to select 3D Format.
 Press  and   to select from:
Sequential
Dual Pipe
Frame Packing
Top-And-Bottom
Side-By-Side (Half)
•
Notes
 
3D may not be present on some 
models
 None of the 3D options are 
avialable unless  3D Mode is set 
to...

Page 4.56 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Dark Time
Ghosting can be caused by the left and right images overlapping during t\
he time 
that the Z screen or 3D glasses are switching.
Press 
 and   to select Dark Time.
 Press  and   to adjust the slider (0 to 6000 µS).
Frame Dominance
The outgoing 3D frames...

Rev C  April 2011 Page 4.57
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 3D may not be present on some 
models
 None of the 3D options are 
avialable unless  3D Mode is set 
to Consumer or Professional.
  In order to achieve maximum 
light output and a smooth 
greyscale, whilst eliminating 
ghosting, the following 
procedure is...

Page 4.58 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Output Shuttering (Frame rate Multiplication)
If the 3D video is available only at low frame rates, it will be necessa\
ry to multiply 
the frame rate to obtain a flicker-free image. For example, a 60Hz frame rate can be 
doubled to 120Hz, or a 48Hz frame rate...

Rev C  April 2011 Page 4.59
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Lens Setup
Press  and   to select Lens.
 Press  to open the Lens submenu.
Centre Lens
Press  and   to select Centre Lens.
 Press  to centre the lens.
Calibrate Focus
Press  and   to select Calibrate Focus.
 Press .
The focus mechanism will operate for about a...

Page 4.60 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Restore Defaults will restore 
all settings to factory 
defaults. All ISF settings will 
be lost (see next page).
  If you are not sure this is 
what you want to do, then 
either:
 make a record of all settings 
first 
 
or 
select No, then press 
....