Digital Projection Titan Sx+ 3d, Dual 3d, Titan Sx+ 3d, Dual 3d Ultra Contrast User Manual

							Rev C  April 2011 Page 4.51
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 IP Address cannot be changed 
if DHCP is set to ON.
 DHCP will set the the address, 
which will be displayed for 
information only.
Setup menu, Network continued
DHCp
Press  and   to select DHCP
 Press  to open the DHCP control box.
 Press  and   to select from:
On
Off
 Press   to apply the new DHCP setting.
or  Cancel
Press   or   to exit without making the change.
Ip Address
Press  and   to select IP Address
 Press  to open the IP Address control box.
 Use  and   to select each number in turn.
 Use  and   to adjust the number
 then move to the next number.
 Use  and   to select from
Apply
 Press   to apply the new IP Address.
or  Cancel
Press   or   to exit without making the change.
•
• 
						

							Page 4.52 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 IP Subnet cannot be changed if 
DHCP is set to ON.
  DHCP will set the the subnet 
mask, which will be displayed 
for information only.
Subnet Mask
Press  and   to select Subnet
 Press  to open the Subnet control box.
 Press  and   to select from:
Automatic
or one of the following:
Class C Masks
255.255.255.254  
255.255.255.252  
255.255.255.248  
255.255.255.240  
255.255.255.224  
255.255.255.192  
255.255.255.128  
255.255.255.0   (selected when setting is Automatic and IP class is C )
Class B Masks
255.255.254.0  
255.255.252.0  
255.255.248.0  
255.255.240.0  
255.255.224.0  
255.255.192.0  
255.255.128.0  
255.255.0.0  (selected when setting is Automatic and IP class is B)
Class A Masks
255.254.0.0  
255.252.0.0  
255.248.0.0  
255.240.0.0  
255.224.0.0  
255.192.0.0  
255.128.0.0  
255.0.0.0 (selected when setting is Automatic and IP class is A)
  Use  and   to select from
Apply
 Press   to apply the new Subnet Mask.
or  Cancel
Press   or   to exit without making the change.
•
Setup menu, Network continued 
						

							Rev C  April 2011 Page 4.53
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Gateway Mask
Press  and   to select Gateway
Press 
 to open the IP Address control box.
Use 
 and   to select each number in turn.
Use  and   to adjust the number
then move to the next number.
Use 
 and   to select from
Apply
  Press   to apply the new IP Address.
or  Cancel
Press   or   to exit without making the change.
Wifi Channel
Press  and   to select Wifi Channel.
 Press  to open the Wifi Channel control box.
 Press  and   to select the channel number.
 Use  and   to adjust the channel number from:
0 to 14
 Use  and   to select from
 Apply
 Press   to apply the new Wifi Channel number.
or  Cancel
Press   or   to exit without making the change.
SSID
Projector’s ID  - for information only.
•
•
•
Setup menu, Network continued
Notes
 IP Gateway cannot be changed 
if DHCP is set to ON.
 DHCP will set the the gateway 
mask, which will be displayed 
for information only.
 The Wifi Channel  setting is not 
available if  Connection  is set to 
Wired. 
						

							Page 4.54 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 3D may not be present on some 
models
 
Setup Menu  
 3D
 If FastFrame  is turned on, then 
setting 3D Mode to Consumer 
or Professional will turn it off.
  When 3D Enable is on, it is not 
possible to turn on  FastFrame.
 It is important that 3D Input 
Assign is set correctly, so that 
the sync signal for the glasses 
or Z-screen is assigned to the 
correct input signal.
  WUXGA models only: 
3D images are possible only on 
Input 8.
3D Setup
Press  and   to select 3D.
  Press  to open the 3D submenu.
3D Mode
 Press  and   to select 3D Mode.
 Press  and   to select from:
Off
Professional
      all options will be available for adjustment
Consumer      3D Input Assign, 3D Format and Output Shuttering will 
be unavailable
In Consumer mode, the projector will automatically detect the following common 
3D standards:
Input 8
    Frame Packing:  1080p 24, 720p 50, 720p 60
Input 3     Frame Packing:  1080p 24
      Side by Side: 1080i 60
3D Input Assign
 Press  and   to select 3D Input Assign.
 Press  and   to select from:
1. RGB1
2. RGB2
3. DVI (Single)
4. SDI
5. Composite Video
6. S-Video
7. Component
8. DVI 3D
•
•
•
Setup menu, continued 
						

							Rev C  April 2011 Page 4.55
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
3D Format
Press  and   to select 3D Format.
 Press  and   to select from:
Sequential
Dual Pipe
Frame Packing
Top-And-Bottom
Side-By-Side (Half)
•
Notes
 
3D may not be present on some 
models
 None of the 3D options are 
avialable unless  3D Mode is set 
to Consumer or Professional.
Setup menu, 3D Setup continued
Sequential
Frame PackingTop and BottomSide by Side (Half)
Dual Pipe
Main Input
Sub Input 
						

							Page 4.56 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Dark Time
Ghosting can be caused by the left and right images overlapping during t\
he time 
that the Z screen or 3D glasses are switching.
Press 
 and   to select Dark Time.
 Press  and   to adjust the slider (0 to 6000 µS).
Frame Dominance
The outgoing 3D frames are in pairs - the dominant frame being presented\
 first.
Press 
 and   to select Frame Dominance
 Press  and   to select from:
Left
Right
•
•
Notes
 
3D may not be present on some 
models
 None of the 3D options are 
avialable unless  3D Mode is set 
to Consumer or Professional.
  In order to achieve maximum 
light output and a smooth 
greyscale, whilst eliminating 
ghosting, the following 
procedure is recommended:
Set the Dark Time to a value 
appropriate to the glasses or 
Z-screen, say 1000 µS.
Adjust the Sync Delay time 
(see next page) to eliminate 
ghosting and achieve a smooth 
greyscale.
Repeat steps 1 and 2 until the 
best result is obtained.
 Set the frame dominance to 
match the incoming 3D video 
frame sequence.
1.
2.
3.
Setup menu, 3D Setup continued
Fully on
Fully off
Left
Right
Dark  time Dark 
time Dark 
time
Dominance Left
Dominance Right
LEFT 1RIGHT 1 LEFT 2RIGHT 2 LEFT 3RIGHT 3
LEFT 3RIGHT 1 LEFT 1RIGHT 2 LEFT 2RIGHT 3 
						

							Rev C  April 2011 Page 4.57
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 3D may not be present on some 
models
 None of the 3D options are 
avialable unless  3D Mode is set 
to Consumer or Professional.
  In order to achieve maximum 
light output and a smooth 
greyscale, whilst eliminating 
ghosting, the following 
procedure is recommended:
Set the Dark Time (see 
previous page) to a value 
appropriate to the glasses or 
Z-screen, say 1000 µS.
Adjust the Sync Delay time to 
eliminate ghosting and achieve 
a smooth greyscale.
Repeat steps 1 and 2 until the 
best result is obtained.
  Use this if the left and right 
images appear to be swapped.
1.
2.
3.
3D Sync Delay
The sync signal from the 3D server will be in phase with the frames gene\
rated by 
its graphics card. However, to compensate for processing delays in the projector, 
this control is provided to introduce a delay to the sync output signal \
sent to the 
Z screen or 3D glasses.
Press  and   to select Sync Delay.
 
Press  and   to adjust the slider (-1500 to +1500 µS).
3D Sync Source
Press  and   to select 3D Sync Source.
 Press  and   to select from:
External
Internal
3D Sync Output polarity
Press  and   to select 3D Sync Output Polarity.
 Press  and   to select from:
Positive
Negative
•
•
•
Setup menu, 3D Setup continued
Incoming 
video
Incoming 
sync signal
Video signal with 
processing delays (and   dark time adjustment)
Sync output signal after  delay adjustment 
						

							Page 4.58 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Output Shuttering (Frame rate Multiplication)
If the 3D video is available only at low frame rates, it will be necessa\
ry to multiply 
the frame rate to obtain a flicker-free image. For example, a 60Hz frame rate can be 
doubled to 120Hz, or a 48Hz frame rate could be tripled to 144Hz.
Press 
 and   to select Output Shuttering.
 Press  and   to select from:
x1
x2
x3
x2 Example
•
Setup menu, 3D Setup continued
Notes
 3D may not be present on some 
models
 None of the 3D options are 
avialable unless  3D Mode is set 
to Consumer or Professional.
  WUXGA models only: 
The maximum Frame Rate 
Multiplication available for 
WUXGA and UXGA images is 
x2.
L1
R1 L2
R2
L1
L1
R1R2
L2 L3
R2
R1
L3
L2
IN
OUT 
						

							Rev C  April 2011 Page 4.59
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Lens Setup
Press  and   to select Lens.
 Press  to open the Lens submenu.
Centre Lens
Press  and   to select Centre Lens.
 Press  to centre the lens.
Calibrate Focus
Press  and   to select Calibrate Focus.
 Press .
The focus mechanism will operate for about a minute, whilst the minimum \
and 
maximum travel distances are determined.
Calibrate Zoom
Press  and   to select Calibrate Zoom.
 Press .
The zoom mechanism will operate for about a minute, whilst the minimum a\
nd 
maximum travel distances are determined.
•
•
•
•
Setup menu, continued
Notes
 Each time a new lens is 
fitted to the projector, the 
calibration procedure must 
be carried out.
  Note that two shortcuts are 
available using the remote 
control:
 Calibrate Focus:  
 Calibrate Zoom:   
						

							Page 4.60 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Restore Defaults will restore 
all settings to factory 
defaults. All ISF settings will 
be lost (see next page).
  If you are not sure this is 
what you want to do, then 
either:
 make a record of all settings 
first 
 
or 
select No, then press 
.
 Following a restore to factory 
defaults, the projector will 
perform a self-test and enter 
Standby mode.
  This process will take up to 10 
seconds. During this time the 
projector will not respond to any 
commands.
 When complete, all settings will 
be restored to factory condition 
and all user settings will be 
removed except for downloaded 
colour and gamma parameters.
Restore Defaults
Press  and   to select Restore Defaults.
 Press .
 The following message will be displayed.
 Press  and   to select from:
Yes
 Press   to confirm your that you really wish to restore all default settings.
All settings will be restored to factory defaults.
or  No
Press   or   to exit without making the change.
•
•
Setup menu, continued