Digital Projection Titan Sx+ 3d, Dual 3d, Titan Sx+ 3d, Dual 3d Ultra Contrast User Manual

							Rev C  April 2011 Page 2.7
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
NotesChoosing a lens using the lens charts
Use the chart below to choose which lens best suits your application.
Example
For a screen width of 12m at a distance of 35m, the 2.77 - 4.51: 1 zoom \
lens 
would be best suited.
For the same screen size at a distance of 60m, the 4.51 - 7.53: 1 zoom l\
ens 
would be best suited.
if you need to be more precise, then use the calculations on the page im\
mediately 
following the lens chart. •
•
feetmetres
Screen width
              10             20             30             40           \
  50             60            70             80 metres
              33             66             98            131           \
164           197          230          262 feet
 
66  20
 49  15
 33  10
 16  5
Throw distance
1.2 : 1 fixed lens 
(1.2 - 2m)
105-609
105-609 1.5 - 2.02 : 1 
zoom lens
105-610
107-196 2.02 - 2.77 : 1 
zoom lens
105-611
107-197 4.51 - 7.53 : 1 
zoom lens
105-613
107-199
0.73 : 1 fixed lens 105-607
107-195 2.77 - 4.51 : 1 
zoom lens
105-612
107-198
1.2 : 1 fixed lens  (3 - 15m)
105-608
105-608
1.26 - 1.61 : 1 
zoom lens
109-236
109-359 7.5 - 11.2 : 1 
zoom lens
109-235
109-358 
						

							Page 2.8 Rev C  April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
 The Throw ratio for a particular 
lens is fixed, and assumes that 
the image fills the width of the 
DMD.
  For images that do not fill the 
width of the DMD, the Throw 
ratio is effectively increased. To 
correct for this, a Throw Ratio 
Factor (TRF) is used. 
Choosing a lens by calculation
For any screen size not listed above, or if you need to be more precise,\
 then use the 
calculations below.
Identify actual width of the image in pixels.
Calculate the Throw Ratio Factor:  TRF = DMD width (1400) 
            Image width in pixels
Identify the screen width required.
Identify the throw distance required.
Throw distance calculations are based on the distance from the outer end\
 of the 
lens, which will vary from lens to lens. Once a lens has been chosen, th\
e figures 
can be checked using the lens extension values given on the next page.
Calculate the throw ratio required.  Throw ratio =  Throw distance        
              Screen width x TRF
Choose a lens with the required throw ratio from the list at the bottom \
of the 
page.
Check from the list that the lens chosen will work at the throw distance\
 required.
Example
An image, 1024 x 768 pixels, screen width 6.5m, throw distance 18m from \
the 
outer end of the lens.
Throw Ratio Factor (TRF) = 1400  = 1.37 
        1024
Throw ratio required =      18   = 2.02 
      6.5 x 1.37
Choose the 2.0 - 2.77  zoom lens.
•
•
•
•
•
•
•
•
•
•
 
High Brightness High Contrast Throw distance range
0.73 : 1 fixed lens  105-607 107-195 1.1 - 3.2m (3.6 - 10.5ft)
1.2 : 1 fixed lens (3 - 15m)  105-608 105-608 3 - 15m (9.8 - 49.2ft)
1.2 : 1 fixed lens (1.2 - 2m)  105-609 105-609 1.2 - 2m (3.9 - 6.6ft)
1.26 - 1.61 : 1 zoom lens  109 236 109-359 3 - 15m (9.8 - 49.2ft)
1.5 - 2.02 : 1 zoom lens  105-610 107-196 4 - 24m (13.1 - 78.7ft)
2.02 - 2.77 : 1 zoom lens  105-611 107-197 4 - 24m (13.1 - 78.7ft)
2.77 - 4.51 : 1 zoom lens  105-612 107-198 9.1 - 45m (29.9 - 147.6ft)
4.51 - 7.53 : 1 zoom lens  105-613 107-199 12 - 80m (39.4 - 262.5ft)
7.5 - 11.2 : 1 zoom lens  109-235 109-358 12 - 80m (39.4 - 262.5ft) 
						

							Rev C  April 2011 Page 2.9
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Notes
 The Throw ratio for a particular 
lens is fixed, but assumes that 
the image fills the width of the 
DMD.
  For images that do not fill the 
width of the DMD, the Throw 
ratio is effectively increased. To 
correct for this, a Throw Ratio 
Factor (TRF) is used.
Useful lens calculations
The following lens calculations may be useful:
Throw ratio
  =  Throw distance 
   Screen width
Throw ratio factor (TRF)  = DMD width in pixels = 1400                           
   image width in pixels    image width in pixels
Therefore:
Screen width  = Throw distance 
   Throw ratio x TRF
Throw distance  = Screen width x Throw ratio x TRF 
Lens extension
The throw distance calculated above is to the outer end of the lens. For\
 each lens, 
the nominal distance between the front of the projector and the outer en\
d of the lens 
(lens extension) will be as listed below.
  High Brightness/ Contrast Lens extension (±2%)
0.73 : 1 fixed lens  105-607 107-195 204 mm (8.0 in)
1.2 : 1 (3 - 15m) fixed lens  105-608 105-608 268 mm (10.6 in)
1.2 : 1 (1.2 - 2.0m) fixed lens  105-609 105-609 268 mm (10.6 in)
1.26 - 1.61 : 1 zoom lens  109 236 109-359 226 mm (8.9 in)
1.5 - 2.02 : 1 zoom lens  105-610 107-196 194 mm (7.6 in)
2.02 - 2.77 : 1 zoom lens  105-611 107-197 159 mm (6.3 in)
2.77 - 4.51 : 1 zoom lens  105-612 107-198 145 mm (5.7 in)
4.51 - 7.53 : 1 zoom lens  105-613 107-199 129 mm (5.1 in)
7.5 - 11.2 : 1 zoom lens  109-235 109-358 179 mm (7.0 in)
lens extension, 
measured from front 
of corner post 
						

							Page 2.10 Rev C  April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
 Each time a new lens is 
fitted to the projector, 
the calibration procedure 
must be carried out. See 
Setup menu, in Section 4. 
Controlling the projector.
  Make sure the rear lens cap is 
removed, before fitting the lens.
 Be careful not to scratch 
the lens surfaces. If you do 
accidentally touch a lens, then 
clean the surface using a lens 
paper.
 The lens release lever should 
always be set to the locked 
position, as shown on the 
next page, to prevent the lens 
from falling out.
Zoom drive connector
Fitting the lens
Turn the lens release lever clockwise so that it is pointing upwards, to \
open the 
lock fully.
Remove the rear lens cap from the lens.
Insert the lens into the lens aperture, making sure that the plug on the\
 zoom 
drive mechanism lines up with the socket on the front of the projector, then push 
the lens in firmly as far as it will go.
•
•
•
Lens release 
lever, open
Lens release 
lever, mid-
position
Turn the lens release lever anti-clockwise to the mid-position, as shown \
below.
•
The lens can now be pushed in further. Push the lens in firmly as far as it will go.
• 
						

							Rev C  April 2011 Page 2.11
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Notes
 Be careful not to scratch 
the lens surfaces. If you do 
accidentally touch a lens, then 
clean the surface using a lens 
paper.
 The lens release lever should 
always be set to the locked 
position to prevent the lens 
from falling out.
  Make sure the front lens cap is 
removed, before switching on 
the projector.
 Lens clamp kit, part number 
111-256, comprises:
  2 x lens clamp quadrants 
4 x 20mm M3 allen screws
Turn the lens release lever anti-clockwise so that it is pointing downwar\
ds, to 
close the lock fully.
•
Lens release 
lever, locked
Fixed lens clamp
In addition to the lens lock, any of the fixed lenses can be permanently\
 secured to 
the projector, as follows:
Fit and lock the lens to the projector, as described above.
Fit the two clamp quadrants either side of the lens, as shown below, and secure 
them with the four screws.
•
•
Lens clamp 
quadrants 
						

							Page 2.12 Rev C  April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
 For more information on using 
the Lens shift feature, see 
section 4. Using the menus, 
Using the control keys.
 If the lens is to be shifted in 
two directions combined, the 
maximum range is somewhat 
less, as can be seen below. 
(zoom lens shift shown).
full horizontal or vertical shift  
without distortion
combined shift  
is reduced
Shifting the image
The normal position for the projector is at the centre of the screen. Ho\
wever, you 
can set the projector above or below the centre, or to one side, and adjust the image 
using the Lens shift feature to maintain a geometrically correct image.
Any single adjustment outside the ranges specified below may result in a\
n 
unacceptable level of distortion, paricularly at the corners of the imag\
e, due to 
the image passing through the periphery of the lens optics.
If the lens is to be shifted in two directions combined, the maximum ran\
ge 
without distortion will be somewhat less, as can be seen in the diagrams\
 to the 
right.
The maximum range available with no distortion is dependent on which len\
s is used. 
The tables below show the maximum range for images that fill the DMD. Fo\
r images 
which do not use the full height or width, extra shift will be possible,\
 up to the limit of 
the lens mount movement.
0.73 : 1 fixed lens 
vertical  
(pixels) horizontal
 
(pixels) vertical 
(vs DMD height) 
horizontal
 
(vs DMD width)
± 115 ± 98± 0.11H± 0.07W
 
1.26 - 1.61 : 1 zoom lens   
vertical  
(pixels) horizontal
 
(pixels) vertical 
(vs DMD height) 
horizontal
 
(vs DMD width)
± 380 ± 280± 0.36H± 0.2W
 
1.21 : 1 fixed lenses and all other zoom lenses
vertical  
(pixels) horizontal
 
(pixels) vertical 
(vs DMD height) horizontal
 
(vs DMD width)
+ 525
- 420 ± 280
+ 0.5H
- 0.4H± 0.2W
It is physically possible to shift the lens further than this, however t\
here will be some 
vignetting of the image beyond the ranges specified above. •
• 
						

							Rev C  April 2011 Page 2.13
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Mounting the projector
The projector is designed to be used on a flat surface, but the optional\
 rigging frame 
will allow it to be suspended from a lighting truss or rigging. The four adjustable feet 
under the chassis allow the projector to be lowered onto a flat surface \
without any 
danger of hands being trapped between the bottom frame and the surface.
Chassis adjustment
If the projector is to be operated from a flat surface such as a project\
or table, then 
adjustment of projector level should be made by turning the four feet un\
der the 
chassis.
Fitting the optional rigging frame
Before fitting the rigging frame to the projector:
- remove the four feet;
- discard the bracket supplied for use with Titan sx+500 projectors;
- make sure that all the frame adjusters are set midway.
Secure the  rigging frame to the projector using the screws supplied, as\
 shown 
in the pictures below. Three screws secure each of the adjuster brackets to its 
corner post.
•
•
Fixing 
screws
Adjustable 
foot
Notes
 BEFORE INSTALLING THE 
PROjECTOR, READ 
ALL THE 
WARNINGS BELOW  AND 
ALL THOSE IN IMpOr TANT 
INFOrMATION AT THE 
FRONT OF THIS MANUAL.
  The projector weighs 
approximately 31 kg (68 lbs). 
Use safe handling techniques 
when lifting the projector.
 Make sure that the surface, 
ceiling or rigging that is 
to support the projector 
is capable of supporting 
the combined weight of 
the projector and lens  (see 
specification for weights) .
 Backup safety chains or 
wires should always be used.
 Do not tilt the projector more 
than  ±10° in either direction 
when in use, as this may 
cause serious lamp failure, 
damage the lamp module 
and cause extra cost on 
replacement.
  It may be possible to use 
the projector in other 
orientations, depending on 
lamp configuration. For more 
information, contact Digital 
Projection.
±10°
±10° 
						

							Page 2.14 Rev C  April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Adjusting the rigging frame
Coarse adjustment of projector level should be made by adjusting the len\
gth of 
the supporting wires or chains, or by adjusting the position of the trus\
s or rigging. 
Once the initial coarse adjustment has been made, fine adjustment can be\
 made by 
turning the frame adjusters on the rigging frame:
To tilt the projector forwards and backwards (pitch adjustment), 
turn either the front pair or the rear pair of vertical adjusters, 
taking care to turn both adjusters by the same amount.
To tilt the projector from side to side (roll adjustment), turn either \
the left pair or the right pair of vertical adjusters, taking care to 
turn both adjusters by the same amount.
To rotate the projector around its vertical axis (yaw adjustment), 
turn the single horizontal adjuster at the rear.
•
•
•
Vertical 
adjusters
Horizontal 
adjuster
Notes
  Before suspending the 
projector, make sure that all the 
frame adjusters are set midway.
 Always make adjustments in 
pairs - never make a single 
adjustment - otherwise 
the projector frame could 
become distorted.
 Do not tilt the projector more 
than  ±10° in either direction 
when in use, as this may 
cause serious lamp failure, 
damage the lamp module 
and cause extra cost on 
replacement.
  It may be possible to use 
the projector in other 
orientations, depending on 
lamp configuration. For more 
information, contact Digital 
Projection.
±10°
±10° 
						

							Rev C  April 2011 Page 2.15
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Notes
 When stacking projectors, 
the stack MUST be vertical, 
to ensure that the stresses 
are distributed to all frame 
couplings.
 Make sure that the surface, 
ceiling or rigging that is 
to support the projector is 
capable of supporting the 
combined weight of all the 
projectors and lenses (see 
specification for weights) .
 Do not place heavy objects 
on top of the projector 
chassis. Only the chassis 
corners and the rigging frame 
are capable of withstanding 
the weight of another 
projector.
 Do not try to stack more than 
3 projectors.
 Separate backup safety 
chains or wires should 
always be used for each 
projector.
Stacking projectors
The rigging frame is capable of supporting the weight of up to two other\
 projectors, 
using the built-in frame couplings. The projectors can be stacked on top of each 
other, or suspended below each other.
Carefully lower each projector down onto the top of the others, making s\
ure that 
all four frame couplings engage fully.
Fit a locking pin into each coupling. A ball in the end of the pin prevents the pin 
from falling out – to insert or remove a locking pin, press the butto\
n on the end of 
the pin to release the ball.
Align the images from the projectors, following the instructions on the \
previous 
page and those in 
section  3. Getting started, Adjusting the lens  and 
Adjusting the projected image .
•
•
•
Locking 
pin
Frame 
couplings 
						

							Page 2.16 Rev C  April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
 For more information on 
selecting an input source, see 
section 4. Overview, Using 
the control keys, and Using 
the menus.
 
  For more information about pin 
connections and control codes 
see section 7. Appendix.
  For more information on 
input modes see  section 
4.
 Overview.
  Input 8 and 3D may not be 
present on some models
Connecting the projector
Signal Inputs
The following inputs are available:
5. Composite Video6. S-Video
7. Component
1. RGB1
2. RGB2
3. DVI
4. SDI
Rear Input 
 
connection panel Control 
connection panel Front Input  
connection panel
8. DVI
MAIN
SUB
3D Sync