Digital Projection Titan Sx+ 3d, Dual 3d, Titan Sx+ 3d, Dual 3d Ultra Contrast User Manual

							Rev C  April 2011 Page 2.17
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Input format, DVI input 3
Single DVI-D
Sources upto 1400x1050 resolution; 8 bits per colour; 24- 60Hz.
Input formats, DVI input 8
Single DVI-D
Sources upto 1400x1050 resolution; 8 bits per colour; 24- 60Hz.
(Use MAIN input only)
Dual DVI-D
An input with increased frame rate.
Sources upto 1400x1050 resolution; 8 bits per colour; 24-120Hz.
(Use MAIN input only)
Twin Link (Twin Single DVI-D)
One input with increased bit depth, using both input connections:
Sources up to 1400x1050 resolution; 10 or 12 bits per colour; 24-60Hz.
(Use MAIN and SUB inputs)
Dual Pipe 3D
Two single input connections:
Sources up to 1400x1050 resolution; 10 or 12 bits per colour, at frame rates 
consistent with up to 148.5 MegaPixels/sec/pipe (including blanking).
(Use MAIN for left eye video stream and SUB input for right eye video s\
tream)
Notes
 There is no scaler on input 8.
  Images up to and including the 
native resolution of the display 
will be displayed pixel for pixel 
and centred.
 This enables the projector to 
maximise the image bandwidth 
and greyscale resolution. 
						

							Page 2.18 Rev C  April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
DVI Input connection examples
Input and processing architecture
 EDID handshaking on the DVI and rGB2 inputs
If you are using a computer DVI card or other source that obeys the EDID\
 
handshaking protocol, then the card or source will automatically configu\
re itself to 
suit the projector.
If not, then you should refer to the documentation supplied with the sou\
rce to 
manually set the resolution to 1400 x 1050 or the nearest suitable setti\
ng. Switch off 
the source, connect to the projector, then switch the source back on again.
Single DVI video source
Single or Dual DVI video source Input 3
Input 8 MAINProjector
Input 8 MAIN
Input 8 SUB
 Twin DVI video source Projector
Notes
 
Dual DVI:
  high bandwidth/frame rate
 Twin DVI:
  increased bit depth/extended 
greyscale
 For important information about 
how Input 8 is used, see INPUT 
8 in the Notes column, and also 
Section 4, Overview. 
						

							Rev C  April 2011 Page 2.19
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Notes
 For important information about 
how Input 8 is used, see INPUT 
8 in the Notes column, and also 
Section 4, Overview.
Projector
3D server
Z screen or  3D glasses
Inputs 1-7
Sync
Video
Sync out
Sync in
Projector
3D server
Z screen or  3D glasses
Input 8
Sync
Video
Sync out
Sync in
3D connection examples
3D sources up to 60Hz, requiring frame doubling and left/right 
interleaving
3D sources up to 120Hz, not requiring frame doubling 
						

							Page 2.20 Rev C  April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
 For more information about pin 
connections and control codes 
see section 7. Appendix.
 For more information about 
using a browser to control the 
projector see  section 4. Using 
the menus.
Computer Null-modem  
cable
Control connection examples
LAN connection
All of the projector’s features can be controlled via a LAN connection, using a 
standard internet browser package such as Internet Explorer.
rS232 connection
Computer Crossed  
LAN cable
Computer
Hub or  LAN Un-crossed 
 
LAN cables
Projector
Serial 
RS232
LAN
Wired 
remote
Projector
Projector Projector 
						

							Rev C  April 2011 Page 2.21
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Notes
 Use only the power cable 
provided.
 Ensure that the power 
outlet includes a Ground 
connection, as this 
equipment MUST be earthed.
 Handle the power cable 
carefully and avoid sharp 
bends. Do not use a damaged 
power cable.
Power connection
When mains power is first applied, the projector will perform a self-tes\
t, then go into 
Standby mode.
The Power indicator on the control panel will show amber until the   POWER 
 
on the remote control or the keypad, is pressed for 3 seconds.
Power connection 
						

							Page 2.22 Rev C  April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 
						

							Rev C  April 2011 Page 3.1
3. Getting Started
Contents
Switching the projector on ........................................................................\
.......................................3.2
Selecting an input or test pattern ........................................................................\
...........................3.2
Input ........................................................................\
........................................................................3.2
Test pattern ........................................................................\
..............................................................3.2
Adjusting the lens........................................................................\
.......................................................3.3
Focus ........................................................................\
......................................................................3.3
Zoom ........................................................................\
.......................................................................3.3
Shift ........................................................................\
.........................................................................3.3
Adjusting the projected image ........................................................................\
................................3.4
Picture settings ........................................................................\
.........................................................3.4
Geometry settings ........................................................................\
.....................................................3.4
Switching the projector off ........................................................................\
.......................................3.4 
						

							Page 3.2 Rev C  April 2011
3. Getting Started Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Selecting an input or test pattern
Input
Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI (Single)
4. SDI
5. Composite Video
6. S-Video
7. Component
8. DVI (Single/Dual/Twin pixel-mapped)
Or press the numbered keys 1–8 to change directly to the input:
Test pattern
 If you have no video source connected to the projector, then you can display a test 
pattern as follows:
Press 
 on the remote control, to select a test pattern.
•
•
•
Switching the projector on
Connect the power cable between the mains supply and the projector.
Wait until the self-test has completed and the power indicator on the con\
trol 
panel shows amber. The lamp will be off, the shutter closed, and the projector 
will be in STANDBY mode.
Press POWER 
 on the remote control or the keypad, and hold for about 3 
seconds to switch the projector ON. The power indicator on the control panel will 
show green, the lamp will light and the shutter will open.
•
•
Notes
 
For more information about 
connecting the power cable, 
see Power Connections , in 
section 2. Installation .
 For more detailed information 
about:
  - using the control keys on the 
remote control or keypad,
 - using the menus,
 see the next section: 
Controlling the projector .
 3D images will be displayed in 
3D, only if  3D Mode is set to on: 
see section 4.Controlling the 
projector, Setup Menu, 3D .
 3D WUXGA images are 
possible only on Input 8.
 For important information about 
how Input 8 is used, see INPUT 
8 in the Notes column, and also 
Section 4, Overview.
  Only the Corrected White test 
pattern on Input 8 will fill the 
full height of the DMD, using all 
1200 pixels. All other patterns 
will be 1080 pixels high.
Power 
connection 
						

							Rev C  April 2011 Page 3.3
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 3. Getting Started
Notes
 Each time a new lens is 
fitted to the projector, 
the calibration procedure 
must be carried out. See 
Setup menu, in Section 4. 
Controlling the projector.
  For more detailed information 
about:
  - using the control keys on the 
remote control or keypad,
 - using the menus,
 see the next section: 
Controlling the projector .
 When any of the three Lens 
adjustment keys is pressed, the 
blue Transmit indicator on the 
remote control will light for 10 
seconds:
  - after 10 seconds, if no 
adjustment has been made, 
the indicator will go out and 
the Lens adjustment key must 
be pressed again to resume 
adjustment.
 - to end the adjustment before 
10 seconds has elapsed, press 
the  
 key.
 - all other adjustments will 
be locked out until the Lens 
adjustment is ended.
Adjusting the lens
Focus
Press  followed by  and  to adjust the focus.
When adjustment is finished, press .
Zoom
Press  followed by  and  to adjust the zoom.
When adjustment is finished, press .
Shift
Press  followed by , ,  or  to shift the lens up, down, left or 
right.
When adjustment is finished, press 
.
•
•
• 
						

							Page 3.4 Rev C  April 2011
3. Getting Started Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Adjusting the projected image
Picture settings
Press a  key, followed by  and   to adjust these picture settings:
 Brightness    BRI 
Contrast    CON 
Saturation    SAT 
Phase    PHASE 
Aspect ratio    ASPECT
Geometry settings
Press Keystone  KEYST
followed by  and  to adjust the keystone correction.
Press Position   POS  (for all inputs except DVI)
followed by , ,  and  to adjust the picture position, for images 
smaller than the DMD.
Switching the projector off
Press POWER  on the remote control or keypad, and hold for 3 seconds, 
to switch the projector OFF.
•
•
•
•
Notes
 
The Saturation control is 
available for Composite, S-
Video and Component inputs 
only.
  The Phase control is available 
for RGB inputs only.
  None of the Geometry controls 
are available for Input 8.
  For more detailed information 
about:
  - using the control keys on the 
remote control or keypad,
 - using the menus,
 see the next section: 
Controlling the projector .
 For all adjustments that require 
more than one key to be 
pressed:
  - after 10 seconds, if no 
adjustment has been made, 
the indicator will go out and 
the adjustment key must be 
pressed again.
 - to end the adjustment before 
10 seconds has elapsed, press 
a different adjustment key, or 
press the Exit key.
 Always allow the lamp to cool 
for 5 minutes before:
 - disconnecting the power  
- moving the projector