Digital Projection Titan Sx+ 3d, Dual 3d, Titan Sx+ 3d, Dual 3d Ultra Contrast User Manual

							Rev C  April 2011 Page 4.61
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Information Menu
 If Distributed By is visible, then 
the installer is  ISF Certified, 
and the Save and Delete 
Preset  options will not be 
available. Contact the installer 
for more information.
 
Information Menu  
 Projector Information
 Lightning projectors have only 
one lamp.  
 
Titan projectors may have one 
or two lamps.
 
Information Menu  
 Source Information
Information menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Information is highlighted.
Press  to open the Information menu. The blue highlight moves to the first 
item in the menu.
Projector Information
Press  and   to select Projector Information.
  Press  to open the Projector Information submenu.
Source Information
Press  and   to select Source Information.
 Press  to open the Source Information submenu.
•
•
•
Input
Picture
Geometry
Colour
Setup
Information
Input: DVI
Standard: 720p 60
Frequency V: 60Hz H: 45.0KHz SOURCE INFORMATION 
						

							Page 4.62 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Digital Projection Information
Press  and   to select Digital Projection.
 Press  to see the DP Information screen.
•
Information menu continuedNotes
  When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Information Menu  
 DP Contact Information 
						

							Rev C  April 2011 Page 5.1
5. Userware
continued
Contents
Introduction ........................................................................\
..................................................................5.4
Applet version........................................................................\
...........................................................5.4
Disconnect ........................................................................\
............................................................5.4
Reconnect........................................................................\
.............................................................5.4
Standalone version ........................................................................\
...................................................5.5
Disconnect ........................................................................\
............................................................5.5
Reconnect........................................................................\
.............................................................5.5
Show page ........................................................................\
....................................................................5.6
On / Off ........................................................................\
....................................................................5.6
Shutter Open / Closed ........................................................................\
...............................................5.6
Freeze / Un-Freeze ........................................................................\
...................................................5.6
Picture sliders ........................................................................\
...........................................................5.6
Input Presets ........................................................................\
............................................................5.7
Recall ........................................................................\
..................................................................5.7
Save ........................................................................\
....................................................................5.7
Orientation ........................................................................\
...............................................................5.8
Input ........................................................................\
........................................................................5.8
Test Pattern ........................................................................\
..............................................................5.8
Aspect Ratio ........................................................................\
.............................................................5.8
Lens page ........................................................................\
.....................................................................5.9
Lens controls ........................................................................\
............................................................5.9
Shutter Open / Closed ........................................................................\
...............................................5.9
Calibrate Focus ........................................................................\
........................................................5.9
Calibrate Zoom ........................................................................\
.........................................................5.9
Edge Blend page ........................................................................\
.......................................................5.10
Markers On / Off ........................................................................\
.....................................................5.10
Active Edges ........................................................................\
..........................................................5.10
Input 8 DVI 3D Resolution ........................................................................\
.......................................5.10
Overlap Width........................................................................\
.........................................................5.10
Black Level Uplift page ........................................................................\
.............................................5.11
x2, x4 Region Uplift ........................................................................\
..................................................5.11
Non-Addressable Border ........................................................................\
..........................................5.11
Back to Edge Blend........................................................................\
..................................................5.11 
						

							Page 5.2 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Image page ........................................................................\
.................................................................5.12
Colour Space ........................................................................\
.........................................................5.12
Component ........................................................................\
............................................................5.12
Phase slider ........................................................................\
...........................................................5.12
Gamma ........................................................................\
..................................................................5.12
Parametric slider ........................................................................\
.....................................................5.12
Convergence controls ........................................................................\
.............................................5.13
Horizontal Convergence ........................................................................\
..........................................5.13
Vertical Convergence ........................................................................\
..............................................5.13
Close ........................................................................\
.....................................................................5.13
Screen page ........................................................................\
...............................................................5.14
Blanking On / Off ........................................................................\
....................................................5.14
Blanking adjust ........................................................................\
.......................................................5.14
Keystone adjust ........................................................................\
......................................................5.14
Position adjust ........................................................................\
........................................................5.14
MCGD page ........................................................................\
................................................................5.15
The MCGD measurement procedure ........................................................................\
........................5.15
MCGD edit boxes ........................................................................\
...................................................5.16
Write to Projector ........................................................................\
....................................................5.16
Read from Projector ........................................................................\
................................................5.16
Save File ........................................................................\
................................................................5.16
Open File ........................................................................\
...............................................................5.16
TCGD page ........................................................................\
.................................................................5.17
TCGD values ........................................................................\
..........................................................5.17
Update Graph ........................................................................\
.........................................................5.18
Save File ........................................................................\
................................................................5.18
Open File ........................................................................\
...............................................................5.18
Write User 1, User 2 ........................................................................\
................................................5.18
Read User 1, User 2 ........................................................................\
...............................................5.18
3D page ........................................................................\
.......................................................................5.19
3D Enable ........................................................................\
..............................................................5.19
3D Input ........................................................................\
.................................................................5.19
Dark Time ........................................................................\
..............................................................5.19
Sync Delay ........................................................................\
.............................................................5.19
Frame Dominance ........................................................................\
..................................................5.19
3D Sync Output Polarity ........................................................................\
..........................................5.19
Frame Rate Multiplier ........................................................................\
..............................................5.20
continued 
						

							Rev C  April 2011 Page 5.3
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
3D Format ........................................................................\
..............................................................5.20
Create 3D Preset ........................................................................\
....................................................5.20
Recall 3D Preset ........................................................................\
.....................................................5.20
Global Colour page ........................................................................\
..................................................5.21
Global Colour Mode ........................................................................\
................................................5.21
Modal Colour page ........................................................................\
...................................................5.22
Modal Colour Mode ........................................................................\
.................................................5.22
Lift and Gain sliders ........................................................................\
................................................5.23
Temperature slider ........................................................................\
..................................................5.23
Information page ........................................................................\
.......................................................5.24
Projector Information ........................................................................\
...............................................5.24
Digital Projection ........................................................................\
.....................................................5.24
FastFrame page ........................................................................\
........................................................5.25
FastFrame Enable ........................................................................\
..................................................5.25
Dark Time ........................................................................\
..............................................................5.25
System page ........................................................................\
..............................................................5.26
OSD ........................................................................\
......................................................................5.26
Backlight ........................................................................\
................................................................5.26
DMD controls ........................................................................\
.........................................................5.26
Lamp mode ........................................................................\
............................................................5.26
Lamp Power slider ........................................................................\
..................................................5.26
Connect page ........................................................................\
.............................................................5.27
Refresh ........................................................................\
..................................................................5.27
Connect ........................................................................\
.................................................................5.27
Disconnect ........................................................................\
.............................................................5.27 
						

							Page 5.4 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 To use the Titan Userware the 
java Runtime Environment 
software must be installed on 
your browser. This software can 
be downloaded, free of charge 
from www.java.com.
  The LAN IP Address of the 
projector can be found in the 
Network submenu of the  Setup 
menu, as described in section 
4. Controlling the projector.
  Whenever the projector is 
connected to mains power, 
whether in  Running mode or 
Standby mode, the Applet 
version of the Userware will be 
available.
  The Applet version of the 
Userware can be used only to 
control the projector from which 
it was downloaded.
  The Userware can be used to 
control only one projector at a 
time, and only one instance can 
be running at one time.
  More than one computer can be 
used to control more than one 
projector on the same network.
Introduction
The Titan Userware provides an intuitive interface to enable control of many of the 
features of the projector from a personal computer, via a LAN connection.
There are two versions of the Userware: the  Applet version, stored on the projector 
and the Standalone version, supplied on disk or from the Digital Projection website.
Applet version
To activate the Userware, simply point the browser at the projector by ty\
ping its 
LAN IP Address into the address bar, then press the Enter key.
The Applet version does not require installation on the personal computer, as it 
is in the form of a Java applet, downloaded automatically from the proje\
ctor by 
the browser. The first time the applet is downloaded, you may see the following 
message:
Tick the box and click OK. In future, the Userware will load immediately.
The Userware interface is organised into a number of pages, as listed be\
low:
Show  Lens    Blend   Image   Screen
MCGD TCGD    3D   Global   Modal
info   FastFrame  System
Each page is described in full later in this section.
When the Userware is started, the Show page  will display immediately. The Page 
buttons are always visible at the bottom of the display:
Disconnect
Navigate away from the projector to disconnect.
reconnect
To reconnect re-type the IP Address in the browser address box then press 
Return.
•
•
•
•
New Java applet download:
Tick the box only if you trust the source.
o  I trust this applet.         OK 
						

							Rev C  April 2011 Page 5.5
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Standalone version
To install the Userware, simply copy the file (from the CD, or downloade\
d from 
the Digital Projection website), to a folder on the computer.
Double click on the filename to start the software.
The Userware interface is organised into a number of pages, as listed be\
low:
Show  Lens    Blend   Image   Screen
MCGD TCGD    3D   Global   Modal
info   FastFrame  System   Connect
Each page is described in full later in this section.
When the Userware is started, the Show page  will display immediately. The Page 
buttons are always visible at the bottom of the display:
Disconnect
To disconnect from the projector, go to the  Connect page and click on 
Disconnect.
reconnect
To reconnect, go to the Connect page and click on Connect.
•
•
•
•
Notes
 
To use the Titan Userware the 
java Runtime Environment 
software must be installed on 
your computer. This software 
can be downloaded, free of 
charge from www.java.com.
  The Userware can be used to 
control only one projector at a 
time, and only one instance can 
be running at one time.
  The Connect page can be 
used to switch control between 
multiple projectors.  
(see later in this section)
  More than one computer can be 
used to control more than one 
projector on the same network.
 The Connect page is described 
in more detail later in this 
section. 
						

							Page 5.6 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Show page
The Show page is the first to display when the browser connects to the p\
rojector.
To return to the Show page  at any time, click on Show.
On / Off
Click On to switch the projector On.
Click Off to switch the projector into Standby mode.
Shutter Open / Closed
Click on Shutter Open to open the shutter.
Click on Shutter Close to close the shutter.
Freeze / Un-Freeze
Click on Freeze to freeze the display on the current frame.
Click on Un-Freeze to un-freeze the display.
Picture sliders
Use the sliders to adjust the  Brightness, Contrast, Saturation, Hue and 
Sharpness of the display.
Click on the number above the slider to return to the default value.
•
•
•
•
•
•
•
•
•
Notes
 
The Freeze function is NOT 
available for Input 8.
Picture 
sliders 
						

							Rev C  April 2011 Page 5.7
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Input Presets
recall
To recall a set of modal and lens* settings that have been saved:
Click on Preset , and select one of the Presets A - S, from the drop down menu.
Click on Recall.
  The projector will switch to the saved input source, and redetect the input mode 
before applying the saved modal and lens* settings.
Save
To save the current input source, mode, modal and lens* settings:
Click on Preset , and select one of the Presets A - S, from the drop down menu.
Click on Save.
  The settings will be saved to the selected preset.
•
•
•
•
Notes
  For more information about 
input modes and input presets, 
see Overview, in section 
4. Controlling the Projector.
 A preset can be applied only to 
the same mode for which it was 
created. If the detected input 
mode does not match, then 
settings from the mode history 
or mode library will be applied 
instead.
  For more information about 
input modes, see  Overview, 
in section 
4. Controlling the 
Projector.
  The lens settings, ie Focus 
position, Zoom position and 
Shift, are included only for the 
first ten presets.
 Presets can also be deleted: 
see Input menu , in section 
4. Controlling the Projector.
Show page continued
Preset 
						

							Page 5.8 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Orientation
Click on Orientation to select from the drop down menu.
Input
Click on Input to select from the drop down menu.
Test Pattern
Click on Test Pattern to select from the drop down menu.
Aspect Ratio
Click on Aspect Ratio to select from the drop down menu.
•
•
•
•
Notes
 
For more information about 
input modes, see  Overview, 
in section 
4. Controlling the 
Projector.
  Input 8 and 3D may not be 
present on some models
 The signal from input 8 will 
be displayed in 3D, only if  3D 
Enable is set to on: see 3D 
Menu,  later in this section.
 For more information about 
test patterns, see Setup menu, 
in section 
4. Controlling the 
Projector.
 For more information about 
aspect ratios, see Picture 
menu and Geometry menu, 
in section 
4. Controlling the 
Projector.
Show page continued
Orientation
Input
Test 
PatternAspect  Ratio