Digital Projection Titan Sx+ 3d, Dual 3d, Titan Sx+ 3d, Dual 3d Ultra Contrast User Manual

							Rev C  April 2011 Page 5.19
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 3D may not be present on some 
models
 For more information about the 
3D settings, see Setup menu, 
in section 
4. Controlling the 
projector.
3D page
To see the 3D page, click on 3D.
3D Enable
Click on 3D Enable to turn 3D mode On  or Off .
3D Input
Click on 3D Input  to select from the drop down menu.
Dark Time
Use the slider to adjust the  Dark Time.
Sync Delay
Use the slider to adjust the Sync Delay.
Frame Dominance
Click on Frame Dominance to select from the drop down menu.
3D Sync Output Polarity
Click on 3D Output Polarity  to select from the drop down menu.
•
•
•
•
•
•
• 
						

							Page 5.20 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 3D files are named 
filename.ps3d.
Frame Rate Multiplier
Click on Frame Rate Multiplier to select from the drop down menu.
3D Format
Click on 3D Format to select from the drop down menu.
Create 3D Preset
Click on Create 3D Preset  to save the current 3D settings to a 3D file on the 
computer.
  When prompted, enter a filename or browse to an existing file that is to be 
overwritten.
Recall 3D Preset
To recall a set of saved 3D settings, click on  Recall 3D Preset
 When prompted, enter a filename or browse to the file that is to be opened.
The name of the last 3D file opened will be displayed against  Last 3D Preset 
Recall.
•
•
•
•
3D page continued 
						

							Rev C  April 2011 Page 5.21
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 The Global page  will not be 
available unless  Global is 
selected in  Modal Colour 
Mode (see next page).
  For more information about 
colour mode, see  Colour menu 
and Setup menu, in section 
4. Controlling the projector.
  Select ColorMAX User 1 or 
ColorMAX User 2,  to use the 
TCGD values set up on the  
TCGD page.
  For more information about 
ColorMAX , read the notes on 
MCGD, TCGD and ColorMAX 
earlier in this section
Global Colour page
To see the Global page , click on Global.
Global Colour Mode
Click on Global Colour Mode  to select from the drop down menu.
•
• 
						

							Page 5.22 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 For more information about 
colour mode, see  Colour menu 
and Setup menu, in section 
4. Controlling the projector.
  Select ColorMAX User 1 or 
ColorMAX User 2,  to use the 
TCGD values set up on the  
TCGD page.
  For more information about 
ColorMAX , read the notes on 
MCGD, TCGD and ColorMAX 
earlier in this section
Modal Colour page
To see the Modal Colour page, click on Modal.
Modal Colour Mode
Click on Modal Colour Mode  to select from the drop down menu.
•
• 
						

							Rev C  April 2011 Page 5.23
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Lift and Gain sliders
Use the sliders to adjust the  Lift and Gain for Red, Green and Blue individually.
Temperature slider
Use the slider to adjust the Colour Temperature between 3,000K and 10,000K.
•
•
Modal Colour page continuedNotes
 
For more information about 
colour mode, see  Colour 
menu, and Setup menu, in 
section 
4. Controlling the 
projector.
  The Lift and Gain sliders are 
available only when  User is 
selected in  Modal Colour 
Mode.
  The Temperature slider is 
available only when  Colour 
Temperature is selected in 
Modal Colour Mode . 
						

							Page 5.24 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
NotesInformation page
To see the Information page , click on Info.
Projector Information
Click on Projector Information  to see the following information about the 
projector and the Userware:
Digital Projection
Click on Digital Projection  to see the following contact information:
•
•
• 
						

							Rev C  April 2011 Page 5.25
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 For more information about the 
FastFrame settings, see Setup 
menu, in section 
4. Controlling 
the projector.
FastFrame page
To see the FastFrame page, click on F-Frame.
FastFrame Enable
Click on FastFrame Enable to turn FastFrame mode On  or Off .
Dark Time
Use the slider to adjust the  Dark Time.
•
•
• 
						

							Page 5.26 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 For more information about 
lamp mode, see  Setup menu, 
in section 
4. Controlling the 
projector.
System page
To see the System page, click on System .
OSD
Click on OSD to turn the on-screen display On  or Off .
Backlight
Click on Backlight to turn the control panel backlight On  or Off .
DMD controls
Click on the DMD buttons to turn each DMD On or Off.
Lamp mode
Click on Lamp mode to select from the drop down menu.
Lamp Power slider
Use the slider to adjust the lamp power from 80% to 100%.
•
•
•
•
•
• 
						

							Rev C  April 2011 Page 5.27
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 The Connect page is available 
only on the Standalone version 
of the Userware.
  The Userware can be used to 
control only one projector at a 
time, and only one instance can 
be running at one time.
  The Connect page can be 
used to switch control between 
multiple projectors.
  More than one computer can be 
used to control more than one 
projector on the same network.
Connect page
To see the Connect page, click on Connect.
Refresh
Click on Refresh  to search the network for projectors.
 Any projectors previously connected, that are now no longer online, will be 
marked Unreachable.
Connect
To connect to a projector, click on one of the  LAN IP addresses in the list, then 
click on Connect.
or
  Double click on a LAN IP address.
Any projector previously connected will be disconnected, and the Userwar\
e will 
connect to the new projector.
  The LAN IP address of the projector that is connected will be highlighted.
 Projector Connected will be shown at the top left of all pages, together with the 
projector’s Serial No and Model.
Disconnect
To disconnect from the projector, click on Disconnect
 Projector Disconnected will be shown at the top left.
•
•
•
• 
						

							Page 5.28 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .