Digital Projection Titan Sx+ 3d, Dual 3d, Titan Sx+ 3d, Dual 3d Ultra Contrast User Manual

							Rev C  April 2011 Page 4.21
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 For more information about 
input modes and input presets, 
see earlier in this section,  Input 
modes and settings.
  The lens settings are the only 
settings saved for Input 8.
 
Input Menu 
  Presets
 
Input Menu 
 Presets 
    Recall Presets A ~ H
 The lens settings, ie Focus 
position, Zoom position and 
Shift, are included only for the 
first ten presets.
 The lens settings are the only 
settings recalled for Input 8.
Presets
Sixteen sets of parameters can be saved and recalled  (A – S). The parameters 
saved for each Preset are:
all settings from the Picture menu,
all settings from the Input menu
all settings from the Geometry menu, except Keystone
all settings from the Colour menu, except the Global settings
all lens position, focus and zoom settings
Press 
 and   to select Presets. 
 Press  to open the Presets submenu.
recall presets
Press  and   to select Recall Preset.
 Press  to open the Recal Presets A ~ H submenu. Any presets that have 
been saved are indicated by their description, for example D: in this ex\
ample.
To recall a set of parameters that has been saved, press 
 and   to select 
one of the Presets.
 For Presets J to S, select Recall Preset J ~ S then press  to open the 
J~S submenu. Press  and   to select the Preset.
 Press  to confirm your selection.
 The Preset parameters will be loaded.
•
•
•
•
Input menu continued 
						

							Page 4.22 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 
Input Menu 
  Presets 
    Save Presets A ~ H
 The lens settings, ie Focus 
position, Zoom position and 
Shift, are included only for the 
first ten presets.
 The lens settings are the only 
settings saved for Input 8.
Save presets
Press  and   to select Save Preset.
 Press  to open the Save Presets A ~ H submenu.
To save the current set of parameters, press  and   to select one of the 
Presets.
 For Presets J to S, select Save Preset J ~ S then press  to open the 
J~S submenu. Press  and   to select the Preset.
 Press  to confirm your selection.
 If this Preset has been used before, but only if the Input source has been 
changed, then the following  message will be displayed.
 Press  and   to select either OK or Cancel.
 Press  to confirm your selection.
 The parameters will be saved to the selected preset, and the following message 
will be displayed.
•
•
Input menu continued 
						

							Rev C  April 2011 Page 4.23
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 
Input Menu 
 Presets 
    Delete Presets A ~ H
Delete presets
Press  and   to select Delete Preset.
 Press  to open the Delete Presets A ~ H submenu.
To delete a saved set of parameters, press  and   to select one of the 
Presets.
 For Presets J to S, select Delete Preset J ~ S then press  to open the 
J~S submenu. Press  and   to select the Preset.
 Press  to confirm your selection.
The following  message will be displayed.
 Press  and   to select either OK or Cancel.
 Press  to confirm your selection.
 The preset will be deleted, and the following message will be displayed.
•
•
Input menu continued 
						

							Page 4.24 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Picture Menu
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 The Saturation slider is 
available for Composite, S-
Video and Component inputs 
only.
  The Hue slider is available for 
NTSC inputs only.
Picture menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Picture is highlighted.
Press  to open the Picture menu. The blue highlight moves to the first item in 
the menu.
Brightness
Press  and   to select Brightness.
  Press  and   to adjust the slider (-128 to +127).
Contrast
Press  and   to select Contrast.
 Press  and   to adjust the slider (-128 to +127).
Saturation
Adjusts the saturation at white peak levels.
Press 
 and   to select Saturation.
 Press  and   to adjust the slider (0 to 255).
Hue
Adjusts the color balance from green to blue, using the red level as a r\
eference.
Press 
 and   to select Hue.
 Press  and   to adjust the slider (0 to 255).
•
•
•
•
• 
						

							Rev C  April 2011 Page 4.25
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 For more information about 
User gamma settings, see 
section 5. Userware .
 Parametric Gamma adjustment 
is available only when 
Parametric  is selected in 
Gamma selection, above.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for RGB1 and RGB2 
inputs only.
  The Phase adjustment is NOT 
available for Input 8.
Gamma Correction
Video recordings are often supplied with a gamma adjustment applied. The \
projector’s gamma adjustment can be used to correct for this.
Press 
 and   to select Gamma.
 Press  and   to select from:
Parametric  Enables the gamma slider
User download Applies the gamma settings made externally using the DP 
Userware on a personal computer. (default gamma of 2.2)
2.2 Limited DVI
  Expands DVI signal to use full dynamic range with gamma 2.2
2.4 Limited DVI Expands DVI signal to use full dynamic range with gamma 2.4
Graphics  Enhanced highlights and contrast
NTSC  NTSC colour space, with a gamma of 2.2
PAL  PAL colour space, with a gamma of 2.2
Linear gamma of 1.0
Punch Enhanced brightness and increased colour saturation for high 
ambient environments.
Parametric Gamma
Press  and   to select Parametric Gamma.
 Press  and   to adjust the slider (1.0 to 3.0 in 0.1 steps).
Phase
Phase should be set automatically by the projector, but can be adjusted manually to 
correct for shimmering or poor quality definition on, for example, fine \
text.
Press 
 and   to select Phase.
 Press  and   to adjust the slider (0 to 31).
•
•
•
picture menu continued 
						

							Page 4.26 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect  is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect  
and V Aspect settings made in 
the Geometry menu.
 Aspect Ratio selection is NOT 
available for Input 8.
  WUXGA models only: 
The full height of the DMD can 
be used only by WUXGA and 
UXGA images.
  For more information, see 
Screen requirements  in 
section 2. Installation.
 The Sharpness slider is 
available for Composite, 
S-Video and Component SD 
inputs only.
Aspect Ratio
Press  and   to select Aspect Ratio.
  Press  and   to select from:
Fill  This will best fit the incoming source to fill either the height or 
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.6:1 (16:10)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
Theaterscope
  Use with the TheaterScope Anamorphic System only. The 
2.35:1 source image is displayed using the full area of the 16:9 
DMD. This is then stretched to 2.35:1 by the lens.
Native
  The image will be displayed pixel for pixel. The image will be 
centred, with a black border if smaller than full resolution or 
cropped if larger.
Sharpness
Press  and   to select Sharpness.
 Press  and   to adjust the slider.
•
•
picture menu continued 
						

							Rev C  April 2011 Page 4.27
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Geometry Menu
 None of the Geometry controls 
are available for Input 8.
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
  When User Aspect  is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect  
and V Aspect settings (see 
next page).
  WUXGA models only: 
The full height of the DMD can 
be used only by WUXGA and 
UXGA images.
  For more information, see 
Screen requirements  in 
section 2. Installation.
Geometry menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Geometry is highlighted.
Press  to open the Geometry menu. The blue highlight moves to the first item 
in the menu.
Horizontal Position
Press  and   to select H Position.
  Press  and   to adjust the slider.
Vertical Position
Press  and   to select V Position.
 Press  and   to adjust the slider.
Aspect Ratio
 Press  and   to select from:
Fill  This will best fit the incoming source to fill either the height or 
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.6:1 (16:10)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
Theaterscope
  Use with the TheaterScope Anamorphic System only. The 
2.35:1 source image is displayed using the full area of the 16:9 
DMD. This is then stretched to 2.35:1 by the lens.
Native
  The image will be displayed pixel for pixel. The image will be 
centred, with a black border if smaller than full resolution or 
cropped if larger.
•
•
•
•
Input
Picture
Geometry
Colour
Setup
InformationH Position
V Position
Aspect Ratio
User H Aspect
User V Aspect
Keystone
Phase
Resolution
Blanking
1.85:1 (Flat)
128
64
500
500
0
127 
						

							Page 4.28 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 None of the Geometry controls 
are available for Input 8.
 Horizontal and Vertical 
Aspect Ratio adjustments are 
available only when  User is 
selected in  Aspect Ratio, (see 
previous page).
  WUXGA models only: 
The full height of the DMD can 
be used only by WUXGA and 
UXGA images.
  For more information, see 
Screen requirements  in 
section 2. Installation.
 Keystone adjustment can be 
found in both the Geometry and 
Projector Setup menus.
 The range of adjustment will 
be dependent on the input 
resolution.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for graphics based 
RGB sources only.
User Horizontal Aspect Ratio
Press  and   to select User H Aspect.
 Press  and   to adjust the slider (internal number – adjust to fit).
User Vertical Aspect Ratio
Press  and   to select User V Aspect.
 Press  and   to adjust the slider (internal number – adjust to fit).
Keystone
Used to correct for distortion caused by the projector being mounted hig\
her or lower 
than the screen.
Press 
 and   to select Keystone.
 Press  and   to adjust the slider.
Phase
Phase should be set automatically by the projector, but can be adjusted manually to 
correct for shimmering or poor quality definition on, for example, fine \
text.
Press 
 and   to select Phase.
 Press  and   to adjust the slider (0 to 32).
•
•
•
•
Geometry menu continued 
						

							Rev C  April 2011 Page 4.29
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 None of the Geometry controls 
are available for Input 8.
 
Geometry Menu 
  Resolution
 Input Detection  should 
normally be set to Automatic. 
However, if the incoming video 
signal is non-standard, the 
projector may not be able to 
select an appropriate input 
mode.
  In this case, Input Detection  
should be set to Manual or 
Custom.
 Input Standard  is available 
only if Input Detection is set to 
Manual .
 WUXGA models only: 
The full height of the DMD can 
be used only by WUXGA and 
UXGA images.
  For more information, see 
Screen requirements  in 
section 2. Installation.
Resolution
Press  and   to select Resolution.
 Press  to open the Resolution submenu.
Input Detection
 Press  and   to select from:
Automatic Allows the projector to automatically detect an appropriate 
input mode for the signal.
Manual Allows the user to select an appropriate input mode from a list 
of common standards.
Custom Allows the user to completely customise the settings to suit the 
incoming video signal.
When Input Detection is set to Manual: Press 
 and   to select Input Standard.
Press  and   to select from:
720p
XGA
XGA+
SXGA-
SXGA
SXGA+
1080p
UXGA
WUXGA
VGA
NTSC
PAL
SVGA
•
•
•
•
Geometry menu continued 
						

							Page 4.30 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
When Input Detection is set to Custom:
Press  and   to select one of the adjustment sliders.
 Press  and   to adjust the slider to match the resolution of the incoming 
video signal.
Blanking
Blanking curtains can be applied to each edge of the picture.
Press 
 and   to select Blanking.
 Press  to open the Blanking submenu.
Blanking On/Off
 Press  and   to select from:
On
Off
Blanking adjust
Press  and   to select the edge to be blanked.
 Press  and   to adjust the slider (0 to 200).
•
•
•
•
Notes
  None of the Geometry controls 
are available for Input 8.
  The adjustment sliders are 
available only if Input Detection 
is set to Custom.
 Total H Samples is available 
for RGB1 and RGB2 inputs 
only.
 V Offset is available for DVI 
input only.
 WUXGA models only: 
The full height of the DMD can 
be used only by WUXGA and 
UXGA images.
  For more information, see 
Screen requirements  in 
section 2. Installation.
 
Geometry Menu 
 Blanking
 The blanking curtains will not 
applied until  Blanking is turned 
On.
  The On Screen Display will 
move to the centre of the DMD 
when Blanking is turned On.
  Set to zero for no blanking, eg 
the top edge in this example.
Geometry menu continued