Digital Projection Titan Sx+ 3d, Dual 3d, Titan Sx+ 3d, Dual 3d Ultra Contrast User Manual

							Rev C  April 2011 Page 4.41
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Black Level Uplift
As it is not possible for any projector to produce an absolute black, an\
y ‘black’ areas 
in the overlapped edges may appear slightly less dark than those in the \
rest of the 
image.
Black Level Uplift can be used to counteract this effect, by raising the\
 black level 
of the rest of the image. The amount of uplift required will be either x\
2 or x4, 
depending on how many images are overlapped, as shown in the examples be\
low.
Examples
 From the Edge Blend menu, press  and   to select Black Level Uplift.
Press  to open the Black Level Uplift Setup submenu.
Uplift Adjustment
Used to determine the amount of uplift.
 Press 
 and   to select x2 Region Uplift or x4 Region Uplift.
For each region, press  and   to adjust the slider (0 to 340).
•
•
•
Setup menu, projector Setup, Edge Blend continuedNotes
 
Setup Menu  
 Projector Setup 
    Edge Blend 
      Black Level Uplift Setup
 This adjustment affects the 
amount of Black Level Uplift, 
not the size of the region.
Four projectors, with four x2 uplift 
regions and four x4 uplift regionsTwo projectors, with two x2 uplift  regions
x2 x2 x4
x4
x4 x4
x2
x2
x2
x2
no uplift
no uplift 
						

							Page 4.42 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 To adjust Manually:
  Working on one projector at a 
time, display a test pattern of 
0% Field (black), set all four 
border adjustments to zero, 
then increase the size of each, 
until the border disappears.
Non-Addressable Border
Around the edge of the DMD is a border of non-addressable ‘always off\
’ pixels. 
Although ‘always off’, a small amount of stray light from these pixels can cause a 
faint border around the projector image.
A small black level adjustment can be applied to remove this border.
Press 
 and   to select Non-Addressable Border.
 Press  and   to select from:
Automatic  (recommended)
Manual
Border Adjustment
Press  and   to select the edge that is to be adjusted.
 For each edge, press  and   to adjust the slider (0 to 255).
•
•
Setup menu, projector Setup, Edge Blend continued 
						

							Rev C  April 2011 Page 4.43
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 
Setup Menu 
 Global Colourimetry
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Read these notes on Colour 
and Global Colourimetry 
before making any settings in 
the Colour menus.
  Note that any changes made in 
the Global Colourimetry menu  
will affect ALL inputs, modes 
and presets for which  Global 
Mode has been selected in 
the Colour menu  (see Colour 
Menu, earlier in this section).
Global Colourimetry
Press  and   to select Global Colourimetry.
Press  to open the Global Colourimetry submenu.
•
•
Setup menu continued
  Notes on Colour and Global Colourimetry
Global Colourimetry  menu (see this section)
After a calibration check on the projector or venue, a set of Global col\
our settings 
can be made in the  Global Colourimetry  menu. These settings are then available 
to be copied at any time using the  Colour Mode setting in the Colour menu, or 
used as a starting point using the  Trim feature in the Colour menu.
Colour  menu (see earlier in this section) .
The settings made in the Colour  menu will be automatically saved in the  Mode 
History, or can be manually saved to one of the  Input Presets (see Input modes 
and settings earlier in this section).
The selections available in  Colour Mode in the Colour menu are:
Global
  Copies the settings made in the Global Colourimetry menu
Temperature Set the colour temperature using the slider
User  Set the Red, Green and Blue Lift and Gain using the sliders
Peak Preset high brightness setting
Video, Film,
Graphic
 Applies the factory set P7 settings
ColorMAX User Applies the User gamma settings made externally using the 
DP Userware on a personal computer 
						

							Page 4.44 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Read the notes on Colour and 
Global Colourimetry earlier 
in this section before making 
any settings in the Colour 
menus.
  Note that any changes made in 
the Global Colourimetry menu  
will affect ALL inputs, modes 
and presets for which  Global 
Mode has been selected in 
the Colour menu  (see Colour 
Menu, earlier in this section).
  The Colour Temperature 
slider is available  only if 
Temperature Mode is selected.
  The RGB Lift and Gain  sliders 
are available  only if  User Mode 
is selected.
Colour Mode
Press  and   to select Colour Mode.
  Press  and   to select from:
Temperature
User
Peak
Video
Film
Graphic
ColorMAX User 1
ColorMAX User 2
Colour Temperature
Press  and   to select Temperature.
 Press  and   to adjust the slider (3,000K to 10,000K. in 100 steps).
rGB Lift
Press  and   to select the parameter to be adjusted.
 Press  and   to adjust the slider.
rGB Gain
Press  and   to select the parameter to be adjusted.
 Press  and   to adjust the slider.
•
•
•
•
Setup menu, Global Colourimetry continued 
						

							Rev C  April 2011 Page 4.45
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Lamp Setup
Press  and   to select Lamp.
 Press  to open the Lamp submenu.
The middle row shows the current lamp setting.
Change Lamp Setting
Press  and   to select Change Lamp Setting.
Press  to open the Lamp Setting control box.
single lamp models
dual lamp models
•
•
Setup menu, continuedNotes
 
Setup Menu
 
 Lamp
 Lightning projectors have only 
one lamp.  
 
Titan projectors may have one 
or two lamps.
continued 
						

							Page 4.46 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Lamp power
Press  and   to select the Lamp Power setting.
 Press  and   to adjust the Lamp Power from:
  80 to 100%  in 1% steps
Lamp Mode
Press  and   to select Lamp Mode.
 Press  and   to select from:
single lamp modes
Lamp 1
  lamp 1 only
Lamp 2 lamp 2 only
Alternate on power up, selects the lamp with the least hours used
dual lamp mode
Lamps 1 and 2
  both lamps
After setting the Power and Mode, press  and   to select from
OK
 Press   to apply the new settings.
or Cancel
 Press   or   to exit without applying the new settings.
The indicators on the control panel will show as follows:
Lamp 1
 off =  OFF
  flashing red = LAMP ERROR green = ON (100%) amber = (80 - 99%)
 flashing green   = LAMP WARM-UP     flashing amber  = COOL-DOWN
Lamp 2
 off =  OFF
 flashing red = LAMP ERROR green = ON (100%) amber = (80 - 99%)
 flashing green   = LAMP WARM-UP     flashing amber  = COOL-DOWN
•
•
•
Setup menu, Lamp Setup continued
Notes
 Lamp Mode applies to Titan 
projectors only:
 For Dual lamp models in single 
lamp mode:
  - if the running lamp fails, the 
other lamp will automatically be 
switched on.
 The Lamp 2 and Alternate 
settings apply to Dual lamp 
models only.
  The selected lamp mode:
  - will not be applied until OK is 
selected
  - will be applied gradually over a 
period of 30 seconds
 - will not be applied until the end 
of any warm-up or cool-down 
period that has already started.
 The Lamp 2 indicator applies 
only to Titan Dual models.  
 
Lightning projectors have only 
one lamp. 
						

							Rev C  April 2011 Page 4.47
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 
Setup Menu 
 On Screen Display
 The On Screen Display will 
move to the centre of the DMD 
when Blanking is turned On.
  (see Geometry menu, earlier in 
this section).
  If a menu is opened, and no 
other key is pressed within the 
period set in the  OSD Timeout 
menu, then the menus will 
disappear. When the  
 key 
is pressed again, the menus will 
reopen at the same point they 
were last viewed.
On Screen Display
Press  and   to select On Screen Display.
  Press  to open the On Screen Display submenu.
OSD position
Press  and   to select OSD Position
 Press  and   to select from:
Upper Left
Upper Centre
Upper Right
Middle Left
Middle Centre
Middle Right
Lower Left
Lower Centre
Lower Right
OSD Size
Press  and   to select OSD Size.
 Press  and   to select from:
Large
Small
OSD Timeout
Press  and   to select the length of the On Screen Display Timeout.
 Press  and   to select from:
  0 to 255 in 1 second steps (when set to zero, the OSD never times out)
•
•
•
•
Setup menu continued 
						

							Page 4.48 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Password
Entry to the password protected area is available to authorised service \
personel 
only.
Press 
 and   to select Password.
 Press  to open the Password control box.
Press  and   to select each digit in turn.
 Press  and   to adjust the digit from:
0 to 9
 then move to the next digit.
 Use  and   to select from
OK
 Press   to enter the password controlled area.
or  Cancel
Press   or   to exit without applying the password.
•
•
NotesSetup menu continued 
						

							Rev C  April 2011 Page 4.49
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 
Setup Menu 
 Comunication
 When fresh batteries are 
inserted in the remote control, 
it will default to address  00. 
Remote control  00 is a master 
control,  able to control all 
projectors.
  If two or more projectors are set 
to the same address, they can 
be controlled from one remote 
control, provided they are 
connected by cable or in range 
of the infra red.
Communication Setup
Press  and   to select Comunication.
 Press  to open the Comunication submenu.
Serial port Baud rate
Press  and   to select Serial Port Baud Rate
 Press  and   to select from:
19200
9600
projector Address
The projector and the remote control need to be set to matching addresse\
s. Read 
the note to the right on this page, and follow the instructions in the o\
rder shown 
below:
1
  Set the projector address:
Press  to open the Projector Address control box.
Press  and   to select the address setting.
 Press   and    to adjust the address from:
00 to 99
 Use  and   to select from
Apply
 Press   to apply the new Projector Address.
or  Cancel
Press   or   to exit without making the change.
2 Set the remote control address as shown in Using the control keys, earlier in 
this section.
•
•
Setup menu continued 
						

							Page 4.50 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 
Setup Menu 
 Network
 Some items may be greyed out 
or not editable, due to the effect 
of other settings made in the 
Network submenu.
  For example, if a Wired 
Connection  is selected:
 Wifi, Channel and SSID will be 
unavailable.
Setup menu continued
Network Setup
Press  and   to select Network.
 Press  to open the Network submenu.
LAN MAC Address
Projector’s unique ID  - for information only - cannot be changed.
Connection
Press  and   to select Connection
 Press  to open the Connection control box.
 Press  and   to select from:
Wired
Wireless
 Press   to apply the new Connection setting.
or  Cancel
Press   or   to exit without making the change.
•
•
•