Digital Projection Titan Sx+ 3d, Dual 3d, Titan Sx+ 3d, Dual 3d Ultra Contrast User Manual

Rev C  April 2011 Page 5.9
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Each time a new lens is 
fitted to the projector, 
the calibration procedure 
must be carried out. See 
Setup menu, in Section 4. 
Controlling the projector.
Lens page
To see the Lens page, click on Lens.
Lens controls
Click on the buttons to Move, Focus and Zoom the lens....

Page 5.10 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 For more information about 
Edge Blend, see  Setup menu, 
in Section 4. Controlling the 
projector.
Edge Blend page
To see the Edge Blend page , click on Blend.
Markers On / Off
Click on Markers On to display the overlap markers.
Click on Markers Off to remove the overlap...

Rev C  April 2011 Page 5.11
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 For more information about 
Black Level Uplift, see 
Setup menu,  in Section 4. 
Controlling the projector.
 Non-Addressable Border 
should always be set to 
Manual.
Black Level Uplift page
To see this page, click on  Black Level Uplift on the Edge Blend page .
x2, x4 Region...

Page 5.12 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Changing the Colour Space 
on this page manually 
overrides the colour space 
for analogue component 
inputs, which may result in an 
incorrectly displayed image.
  The Component selection is 
available for the Component 
input only.
  For more information about 
phase, see...

Rev C  April 2011 Page 5.13
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 The Convergence controls 
open in a new window, to allow 
you to visit the Show page , in 
order to display a  Test Pattern.
Convergence controls
To see these controls, click on  Convergence on the Image page.
The Convergence controls open in a new window.
Horizontal...

Page 5.14 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 The blanking curtains will not 
applied until  Blanking is turned 
On.
  For more information about 
blanking, see  Geometry menu, 
in section 
4. Controlling the 
Projector.
  For more information about 
keystone adjustment, see 
Geometry menu, in section 
4. Controlling...

Rev C  April 2011 Page 5.15
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 Read the notes on MCGD, 
TCGD and ColorMAX below, 
before making any MCGD 
settings.
MCGD page
MCGD - Measured Colour Gamut Data - can be used to correct for a number \
of 
environmental variables, for example:
two or more different projectors
lamp age
different lenses...

Page 5.16 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
To see the MCGD page, click on MCGD .
On first entering the MCGD screen, the MCGD values will show those currently 
loaded into the projector.
MCGD edit boxes
Click on each box in turn, and enter the measured  x and y values for each 
colour.
Write to Projector
Click on Write to...

Rev C  April 2011 Page 5.17
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
TCGD page
TCGD - Target Colour Gamut Data - can be used to match the display to a pre-
defined colour gamut, for example:
to match the MCGD values from another projector
to match a specification from the film maker
To see the TCGD page, click on TCGD.
TCGD values
To enter TCGD...

Page 5.18 Rev C  April 2011
5. Userware Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Update Graph
Click on Update Graph to show the effects of the new color gamut graphically.
Save File
Click on Save to save the values on screen to a TCGD file on the computer.
 When prompted, enter a filename or browse to an existing file that is to be 
overwritten.
Open File
To...