Comdial Scout II Users Guide

							Scout II User Guide
Jun ‘02 Comdial 31
To mount your Scout II charging unit directly to a wall, perform the 
following steps.
1.  Insert two mounting screws into the wall 1-9/10 inches apart.  
Allow about 3/16 of an inch between the wall and screw heads 
for mounting the phone.
2.  Using only the base unit AC adapter supplied with the Scout II, 
plug the AC adapter cord into the AC adapter input jack on the 
base unit.  Note:  Use only the supplied base unit AC adapter:  
EXP9704. 
						

							Installing Scout II
32 Comdial Jun ‘02
3.  Wrap the AC Adapter cord around the strain relief.
4.  Place the charging unit on the posts of the wall screws and push 
down until it is firmly seated. 
						

							Scout II User Guide
Jun ‘02 Comdial 33
5.  Plug the AC Adapter into a standard 120V AC wall outlet.
2.5  Installing the Battery Pack
If you see a low battery notice in the display while you are on a call, 
you can quickly change the battery pack without losing the call.  Your 
telephone holds the call for approximately 20 seconds after you 
remove the battery pack from the handset.  This is ample time during 
a conversation for you to exchange a discharged battery pack for a 
freshly charged one. 
						

							Installing Scout II
34 Comdial Jun ‘02
1.  Remove the battery cover by pressing the latch and sliding the 
cover down until it comes off the handset.
2.  Slide the battery pack down into the handset.  Note: Yo u  m a y  
have to remove the old battery at this time. 
						

							Scout II User Guide
Jun ‘02 Comdial 35
3.  Securely close the battery compartment cover by sliding it up 
until it snaps into place.
2.6  Charging the Handset’s Battery 
Pack
The rechargeable Nickel-Cadmium battery pack must be fully 
charged before using your Scout II for the first time.   Note: Charge 
the battery pack without interruption for 5 hours.
1.  Place the handset in the front slot of the charging unit. 
						

							Installing Scout II
36 Comdial Jun ‘02
2.  Make sure the CHARGE indicator lights.  If the CHARGE 
light doesn’t light, check to see that the AC Adapter is plugged 
in, and that the handset is making good contact with the charg
-
ing unit charging contacts. 
						

							Scout II User Guide
Jun ‘02 Comdial 37
2.7  Charging Spare Battery Packs
The charger unit of your Scout II is equipped to charge the spare 
battery pack with or without the handset in the front slot.
1.  Slide the spare battery pack into the second slot in the charging 
unit until the retaining clip snaps over the top of the pack.
2.  Make sure the BATT CHARGE indicator lights.  If the BATT 
CHARGE indicator doesn’t light, check to see that the AC 
adapter is plugged in, and that the battery pack is making good 
contact with the charging unit charging contacts.  
 
Note: Charge the battery pack without interruption for 12-15 
hours.
3.  When charging is complete, press out on the latch and remove 
the battery pack for use.  Or, if you don’t need the battery pack 
immediately, leave it in the charging compartment; it will not 
overcharge. 
						

							Installing Scout II
38 Comdial Jun ‘02
2.8  Cleaning the Battery and Charging 
Un it  Co n tac ts                                               
To maintain a good charge, it is important to clean all charging con-
tacts on the handset, spare battery pack and charging unit about once 
a month.  Use a pencil eraser or a soft dry cloth.  Do not use any 
liquids or solvents. 
						

							Scout II User Guide
Jun ‘02 Comdial 39
2.9  Attaching the Belt Clip to the 
Handset
You can use the belt clip to attach the handset to your belt or pocket 
for convenient portability.
1.  Slide the clip into the tab slot.
CAUTION
The belt clip is designed to fit snugly onto 
the handset. 
						

							Installing Scout II
40 Comdial Jun ‘02
2.  Press firmly until it snaps into place.
3.  To remove, simply press the retain clip in toward the belt clip 
blade and slide the clip up at the same time.