Comdial LCD Speakerphone System Reference Manual

6. PressTA Pbutton to rejoin the transferred call.
7. After rejoining the conference, press#to place the call on hold
again (creating another unattended conference) or hang up to
terminate the call.
* You can eliminate this step if the installer has configured your
system for quick transfer and you are accessing the E & M line
with a group access code.
If one of the parties does not hang up or you have not terminated the call,
the call will return to you when the line-to-line connection timer expires....

·To drop out of a conference call between you and two outside
lines (creating an unsupervised conference),
1. Hand up (lines remain lighted and in use until one or both outside
parties disconnect).
·To rejoin an unsupervised conference between two outside lines,
1. PressTA P.
NOTE: Conference volume levels depend upon the quality of the
external lines.
7.23 Call Forward Outside System
The Call Forward Outside System (CFOS) feature allows you to forward
incoming or transferred line calls to telephone...

·To deactivate CFOS,
1. PressCFOSinteractive button,
—OR—
pressCFOSpreprogrammed button or pressINTERCOMand
dialS56.
·To join an active CFOS call from the CFOS-enabled station,
1. Note flashing HOLD light indicating active CFOS call, and press
TA P. Join CFOS-forwarded party and CFOS destination in a
conference call.
Comdial has taken reasonable step in the design of all product features,
including CFOS , which protect against unauthorized or fraudulent
access to, or use of, a system, or which protect...

7.24 Mark Problem Line
Your programmer can arrange the system so that you can mark a line that
is not functioning properly. You do this by pressing a pre-programmed
MARKbutton or by dialing a feature code of your choice. After you
have marked a particular line a programmed number of times, the system
takes the line out of service (unless programmed to prevent this from
happening). When the system takes the line out of service, it logs the
condition and triggers an alarm. The printed error log will then...

7.25 Automatic Set Relocation
If your installer has equipped your system with automatic set relocation,
when you move your telephone to a new location, the system will give
you a choice (through a display prompt) as to whether you want to keep
your previous programming or use the programming in the new location.
·To maintain the extension number and programming features
from the old location,
1. Connect the telephone line cord to the new jack.
2. Note the flashing HOLD light and press theHOLDbutton...

7.26 Using The IMIST Module
Impact SCS8324F-**, 8324S-**, and 8312S-** speakerphones equipped
with the optional IMIST module can support an IST device (modem,
FAX machine, industry-standard telephone, etc.) in addition to the LCD
speakerphone. Depending on system programming, the IST device may
be used to make outgoing calls and receive incoming calls.
The functionality of the IMIST module depends on the type of system
you are using.
•The IMIST module will function on a DXP system with the
appropriate...

7.27 Using The Caller ID Feature
The Caller ID feature allows you to view incoming call numbers before
you answer them. Incoming call numbers flash in the lower half of the
LCD. If you answer the call, the number appears in the upper half of the
LCD.
The system also stores numbers that ring on your line but receive no
answer. The system indicates that it has stored ring-no answer numbers
by causing the CID light on your telephone to flash. Pressing theCID
button allows you to view the stored numbers one...

This page remains blank intentionally. 

Sending And Receiving
Non-Verbal Messages
8.1 Message Waiting Light and Messaging
If the system installer designates your LCD speakerphone as acentral
message deskor programs it to have message-wait originate ability, you
can turn on the message-waiting light of any other telephone. This light
lets that telephone user know that you have a message for him or her. In
addition to the message waiting light, leaving a message indication at a
station that is a prime intercom, also causes the dial tone at that...

·To turn off the message waiting light at a busy or idle station,
1. PressINTERCOM.
2.
Dial
#3.
3. Dial extension number of station that was alerted. The
message-waiting light of called station will turn off.
·To turn off the message-waiting light during message-delivering
conversation,
1. PressINTERCOMonce if off-hook, twice if on-hook.
NOTE: Only the person who sent the message and the person
receiving the message can turn the indicator off.
·To receive a message at an alerted station,
1. Observe...