Canon Wux450, Wx520 Multimedia Projector Users Manual

71
Operation
Projecting an Image
Step 8 Turn the Projector Off
1Press the POWER button to display the window shown below.
2When this window is displayed, press the POWER button again to turn off 
the power.After you turn the power off, the projector will enter standby mode once it cools 
down.
If you want to continue projecting without turning off the power, press a button other than 
POWER , or else wait until the confirmation message disappears.
• After turning off the projector, wait at least 5...

72 

73
Table of Contents
Safety Instructions
Before Use
Operation
Projecting an Image
Useful Functions Available 
During a Presentation
Setting Functions from 
Menus
Installation and Maintenance
Installation
Connecting to a Network
Maintenance
Networked Multi-Projection
Networked Multi-Projection 
Overview
Operation in Each Mode
Functions in All Modes
AppendixOther Information
Index
Useful Functions 
Available During a 
Presentation 

74
Useful Presentation Functions
Temporarily Blacking 
Out an Image
Press the BLANK button to black out 
the image.
Press the  BLANK button again to show 
the image.
• You can set the screen state while blacking 
out the image in the menu. ( P107)
• The lamp remains illuminated while the  image is blacked out.
Freezing the Picture
Press the  FREEZE button to freeze the 
moving image. The projector shows the 
following icon.
Press the  FREEZE button again to 
return to the original display.
• It is also...

75
Useful Presentation Functions
Operation
Useful Functions Available During a Presentation
Adjusting the Volume
Press the VOL button. The following 
screen appears.
• You can also adjust the volume level with 
the [ ] / [ ] buttons of the projector.
• Adjust the volume or mute setting on the  computer if the volume level is too low.
• You can also adjust the volume level of the 
speakers connected via the audio output 
terminal.
Muting the Sound
Press the  MUTE button to mute the 
sound. The projector...

76
Useful Presentation Functions
Zooming an Image
Press the +D.ZOOM  button to enlarge 
a part of the image. Press the 
–D.ZOOM  button to reduce the image 
size.
• The magnification appears on the screen.
You can move the enlarged area by 
using the [ ] / [ ] / [ ] / [ ] buttons.
You can restore the original size of the 
image by pressing the  OK button.
Useful when:
• Zooming in on an object such as a 
small graph during a presentation (up 
to 12x).
• Focusing on the current subject.
Screen
Remote...

77
Operation
Useful Functions Available During a Presentation
Projecting Images on a USB Flash Drive
Images stored on a USB flash drive in the projector can be projected as follows. 
You can select the images to project, or you can project images automatically, one 
after another. JPEG images up to 7000x7000 can be projected.
1Insert the USB flash drive in the USB port.
Insert the USB flash drive directly into the projector’s USB port. The USB flash 
drive will not be recognized if you connect it via a...

78
Projecting Images on a USB Flash Drive
4Use the pointer buttons to select a file, and then press the OK button to 
project the image.
Press the [ ] / [ ] buttons to select a file.
To view another page, press the [ ] / [ ] buttons (if other pages are available).
To navigate to a higher or lower folder, select a folder and press the OK button.
5Switch to other images as needed.
To switch to the previous image, press the [ ] button.
To switch to the next image, press the [ ] button.
To rotate images...

79
Operation
Useful Functions Available During a Presentation
Split-Screen Display
Two input images can be projected side by side. This is split-screen display. When 
you activate split-screen display, the curre nt image is shown on the left side, and 
the new image is shown at right. You can change the source of images shown on 
each side by pressing the  INPUT button. However, you cannot specify the same 
input signal (terminal) as the source for both sides.
1Supply two signals to the projector....

80
Split-Screen Display
4Press the INPUT button to select the input signal for the side with control 
rights.
The [Input] menu is displayed. To determine which side is currently under 
control, check the screen ID in orange in the upper right of the menu. The side 
without control rights is labeled with a white circle.
For details on selecting input signals, refer to “Selecting an Input Signal” (P52).
To exit split-screen display, press the  EXIT button on the remote control.
Current input signal of...