Canon Wux450, Wx520 Multimedia Projector Users Manual

121
MULTIMEDIA PROJECTOR
Installation and Maintenance
Request projector installa tion from a qualified 
technician, if possible,  or contact the Canon 
Customer Support Center. Fo r ceiling installation in 
particular, always request in stallation from a qualified 
technician or contact th e Canon Customer Support 
Center. 

122 

123
Table of Contents
Safety Instructions
Before Use
Operation
Projecting an Image
Useful Functions Available 
During a Presentation
Setting Functions from 
Menus
Installation and Maintenance
Installation
Connecting to a Network
Maintenance
Networked Multi-Projection
Networked Multi-Projection 
Overview
Operation in Each Mode
Functions in All Modes
AppendixOther Information
Index
Installation 

124
Before Installation
Precautions When Carrying/Shipping the 
Projector
Precautions for Installation
Be sure to read “Safety Instructions” and “For Safe Use” (P16 – P29 ). Also 
take the following precautions during installation.
Prepare the projector as described below before carrying it.
• Disconnect the cables connected to the projector. Carrying the projector with the cables attached may cause an accident.
• Retract the adjustable feet.
• Do not reuse any packaging or shock-absorbent materials...

Before Installation
125
Installation and Maintenance
Installation
■Do Not Use in the Following Environments
•Do not install the projector in a location that is damp, or where there is a lot of 
dust, oily smoke or tobacco smoke. Opti cal parts such as the lens and mirror may 
be stained, resulting in poor picture quality.
• Do not install the projector near high-voltage  electrical power lines or an electrical 
power source. The projector may not operate correctly.
• Do not use the projector on a soft...

Before Installation
126
■Be Careful of Condensation
If the temperature of the room rises suddenly, moisture in the air may condense on 
the projector lens and mirror, causing the image to become blurred. Wait until the 
condensation has evaporated for the image projected to return to normal.
■At Altitudes above 2,300 m (7,545.8), Adjust the Settings
Projector settings must be adjusted when us ing the projector at altitudes of 2,300 m 
(
7,545.8) or higher. Specifically, refer to instructions for [Fan...

Before Installation
127
Installation and Maintenance
Installation
■Install facing in th e correct direction
When installing the projector facing upward or downward, specify which way the projector 
is facing in [Install settings] > [Professional settings] > [Vertical projection]. ( P148)
10°  10°
10°  10°
10°
10°
The projector can be installed facing any direction*1, as shown 
below. However, projection upward ( ) or downward ( ) may 
shorten the useful life of the lamp. Installation in these...

128
Installation Procedure
Setting Up the Projector
■Positioning the Projector  in Front of the Screen
Place the projector in front of the screen.
■Floor Installation
To adjust the projection position when the projector is installed on the floor, use the 
lens shift function ( P56 and  P131 ) to adjust up / down / left / right. You can also use 
the adjustable feet to incline the projector upward by up to 6°.
For information about the relationship between screen size and projection distance, 
refer to...

Installation Procedure
129
Installation and Maintenance
Installation
■Projection from  High Surfaces
For projection from a shelf or other high  surface, the projector can be installed 
upside-down and the projected image inverted. In this case, attach the option feet 
on top of the projector.
Attaching Option Feet (RS- FT01, Sold Separately)
Remove the hole caps and screw the option feet into the holes.
The caps are located at four positions on top of the projector. They are removed 
differently...

Installation Procedure
130
Removing hole caps labeled (2) 
Open the lamp cover and use a screwdriver or similar tool to 
push off the caps from below.
■Ceiling Mounting or Rear Projection
You can mount the projector on the ceiling  (ceiling mounting) with it turned upside 
down or place it behind the screen (rear  projection) if you use a translucent screen.
Make sure to use the optional ceiling attachment. For the ceiling attachment, refer 
to “Option” ( P299). For details, refer to the assembly and...