Canon Projector WUX450 User Manual

							31
Table of Contents
Safety Instructions
Before Use
Operation
Projecting an Image
Useful Functions Available 
During a Presentation
Setting Functions from 
Menus
Installation and Maintenance
Installation
Connecting to a Network
Maintenance
Networked Multi-Projection
Networked Multi-Projection 
Overview
Operation in Each Mode
Functions in All Modes
AppendixOther Information
Index
Before Use 
						

							
32
Supplied Accessories
Check that the following accessories have been supplied with the projector.
• Remote control • Batteries for the remote control
(AAA size x2)
(part No.: RS-RC06)
Optional remote controls are 
also available (RS-RC04, RS-
RC05). However, some buttons 
are not supported with this 
projector. The RS-RC05 can 
also be used as a wired remote. 
( P36 )
• Computer cable (1.8 m / 5.9)
(mini D-sub 15-pin / mini D-sub 15-pin) • 
Power cord (1.8 m / 5.9)
For Continental 
Europe
•  User’s Manual (CD-ROM) For the U.S.A. and 
Canada
• 
Lens cap
• Warranty Card
•  Important Information
WUX450/WX520 WU X400ST/WX450ST 
						

							
33
Supplied Accessories
Before Use
■Attaching the Lens Cap
When using the WUX450/WX520, align the l ens cap notch with the optical zoom 
adjustment lever as shown and attach the cap.
There is no need to align the lens  cap when using the WUX400ST/WX450ST.
Always remove the cap before 
projection. Accidentally leaving the 
cap on during projection may distort 
the cap and damage the projector. 
						

							34
Preparing the Remote Control
■Installing Remote Control Batteries
• If buttons on the remote control are inoperative when you attempt to operate the 
projector, replace the batteries with new ones.
• Do not drop the remote control or subject it to impact.
• Do not spill any liquids on the remote control. Doing so could damage it.
Pay attention to the following points when handling the batteries. 
Failing to do so could result in a fire or personal injury.
• Do not heat, short circuit or disassemble the batteries, or place 
them in a fire.
• Do not attempt to recharge the batteries that are included with the 
remote control.
• Remove the batteries when they are flat or when the remote control 
will not be used for a long period of time.
• When replacing the batteries, replace both at the same time. Also, 
do not use two batteries of a different type at the same time.
• Insert the batteries with the + and - terminals in the correct 
directions.
• If any liquid from inside the batteries leaks out and contacts your 
skin, be sure to wash the liquid off thoroughly.
3Close the 
compartment lid.
Slide the lid until you 
hear a click to 
securely close it.2Insert batteries.
Insert 2 new AAA 
batteries in the 
compartment with the 
+  and – poles 
positioned correctly.1Open the battery 
compartment lid.
Slide the lid while 
pressing it down. 
						

							35
Preparing the Remote Control
Before Use
■Remote Control Operating Range
The remote control is an infrared type. Point it at the infrared remote receiver on the 
front or rear of the projector to operate it.
• Use the remote control within an angle of 25° in any direction from directly in front of the 
infrared remote receiver.
• The remote control may be inoperative if there is an obstacle between the remote 
control and the projector or the infrared remote receiver on the projector is exposed to 
direct sunlight or strong light of lighting equipment.
• When you use 2 or more projectors at the same time, you can change the channel 
settings to prevent the 2 remote controls from interfering with each other. (P113)
WUX450/WX520 WUX400ST/WX450ST
25°
25°8 m (26.3)
8 m (26.3)
25°25°25°
25°4 m (13.1)
8 m (26.3)
25°25° 
						

							Preparing the Remote Control
36
■Using an Optional Wired Remote (RS-RC05)
To use a wired remote control with the projector, use the RS-RC05, sold separately.
Use a cable with a ø3.5 mm stereo mini jack (not included).
• Infrared operations cannot be performed if a cable is connected to the projector or the 
remote control.
• Use a cable with a ø3.5 mm stereo mini jack (not included) with a length of 30 m (98.4) 
or less.
ø3.5 mm stereo mini jack 
cable (not included)Terminal for wired 
remote control Remote control 
(RS-RC05) 
						

							37
Before Use
Part Names
Projector (WUX450/WX520)
■Front Side
■Rear Side
■Bottom Side
Terminals and 
connectors (P44)Projection lens (P45)
Power cord connector 
(P143) Side control
(P42)
Air intake vent
Air filter (P199)
• Do not block the air intake.
Doing so may cause a malfunction.
• Before projection, always remove the 
cap. Leaving the cap on may damage 
the projector.
Hole caps (P131)
Attach option feet (sold 
separately). For instructions 
on removing the hole caps, 
refer to “Attaching Option 
Feet (RS-FT01, Sold 
Separately)”.
Infrared remote receiver (P35)
Exhaust vent
Infrared remote receiver (P35) Lamp cover
Lens shift 
side control 
(P45)
Anti-theft lock hole
An anti-theft wire cable (not included) can be connected.
Do not block the air exhaust. 
Doing so may cause a 
malfunction.
Adjustable feet (P130) 
						

							Part Names
38
Projector (WUX400ST/WX450ST)
■Front Side
■Rear Side
■Bottom Side
Terminals and 
connectors (P44)Projection lens (P45)
Power cord connector 
(P143) Side control
(P42)
Air intake vent
Air filter (P199)
Hole caps (P131)
Attach option feet (sold 
separately). For 
instructions on removing 
the hole caps, refer to 
“Attaching Option Feet (RS-
FT01, Sold Separately)”.
Infrared remote receiver (P35)
Do not block the air intake.
Doing so may cause a malfunction.
Exhaust vent
Infrared remote receiver (P35) Lamp cover
Lens shift 
side control 
(P45)
Anti-theft lock hole
An anti-theft wire cable (not included) can be connected.
Do not block the air exhaust. 
Doing so may cause a 
malfunction.
Adjustable feet (P130) 
						

							39
Part Names
Before Use
Mounting the Projector on the 
Ceiling
You can mount the projector on the 
ceiling.
The ceiling attachment (part No.: RS-
CL12 (WUX450/WX520), RS-CL13 
(WUX400ST/WX450ST)) is required 
in order to mount the projector on the 
ceiling. Depending on the installation 
environment, an extension pipe (part 
No.: RS-CL08 or RS-CL09) may also 
be required. Contact the Canon 
Customer Support Center for more 
detailed information.
If you mount the projector on the 
ceiling, you have to invert the 
projected image by selecting [Image 
flip H/V] from the menu. (P146)
• Make sure to use the optional 
ceiling attachment.
• You should never install the 
ceiling attachment by yourself. 
						

							40
Part Names
Remote control
The projector can be operated using buttons on the remote control or the side 
control on the projector.
The remote control allows you to operate all functions of the projector.
POWER button (P52, P74)
Turns the projector on or off.
ASPECT button (P67)
Changes the aspect ratio mode.
KEYSTONE button (P68)
Corrects keystone distortion.
The [Keystone] setting enables both 
horizontal/vertical keystone correction 
(by adjusting top/bottom/left/right 
length) and corner correction. 
D.ZOOM button (P78)
Zooms the image in or out digitally.
[+] button: Zooms the image in (up to 
12x).
[–] button: Zooms the image out (1x 
minimum).
[ ] / [ ] / [ ] / [ ] buttons:
Move the zoom-in location.
BLANK button (P76)
Toggles between display / non-display 
of image.
GAMMA button (P100)
Adjusts the gamma of the image.
[ ] button: Corrects dark parts of the 
image so that they are 
easier to see.
[ ] button: Corrects bright parts of 
the image so that they are 
easier to see.
IMAGE button (P71)
Switches the image mode (image 
quality).