Canon Projector WUX450 User Manual

							181
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
4Create a new network environment and set the IP address and subnet 
mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP 
address which is different from this.
Example
IP address: 192.168.254.1
Subnet mask: 255.255.255.0
5Click [Apply] to close the network preference window.
■Resetting the IP Address Setting of the Computer
Follow the same procedure as for changing the IP address and reset the values to 
the original values based on the notes taken before the change.
Setting Up the Network
■Displaying the Network Configuration Screen
1Turn on the computer and projector.
2Launch a web browser, enter “http://(projector IP address)” in the 
address bar, and press the Enter key.
The projector web screen appears.
Network functions are not available for the first 40 seconds after projector startup. 
						

							Completing Computer Settings
182
The following information is displayed.
3Click [Settings] on the web screen.
The password input window appears.
4Enter the user name and password on the password input window, then 
click [OK].
The factory default user name is “root” and the password is “system”.
Network Multiple Projection 
DownloadFor downloading the Networked Multi-Projection 
(NMPJ) program. (P211)
Projector control Displays the projector control screen.
Settings Shows the settings screen.
Projector name The name of the projector on the network
Location The location of projector installation
MAC address The MAC address of the projector
IP address The IP address of the projector
PowerStatus The power status of the projector
LampModeFullPower Lamp operating time in [Full power] lamp mode
LampModePowerSaver Lamp operating time in [Power saver] lamp mode
LampTimeConverted Lamp operating time (converted value)
FilterTime Air filter operating time
AlertError message (if an error has occurred)
Temperature abnormality
Faulty lamp
Faulty cooling fan
Faulty air filter unit
Faulty power supply
The factory default IP address is “192.168.254.254”. If DHCP settings are used, ask the 
network administrator for the projector IP address. It is possible to check the IP address 
from the projector menu. 
						

							183
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
The projector settings screen is displayed in the web browser.
■Network Setting
1To access the settings screen, click [Settings] on the web screen in step 3 
of “Displaying the Network Configuration Screen” (P181).
2Select the function to set from the menu (1), then enter the setting in the 
displayed field (2) and click [OK] (3).
To operate the projector from the computer, click [Projector control] (P195).
(2) (1)
(3) 
						

							Completing Computer Settings
184
3A confirmation window appears. Check the contents and if they are 
correct, click [Apply].
The settings are applied to the projector.
When you select [Network] in the menu, this message is displayed: “Save 
completed. Please change setting and reconnect.”
If you select functions other than [Network], “Save completed” is displayed. 
Click [Back to top] to return to the top page of the web screen.
Setting Basic Information [Network]
From [Network] in the settings screen, you can log into the web screen and set 
basic network information. For the setting procedure, refer to “Displaying the 
Network Configuration Screen” (P181). 
						

							185
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
ItemExplanationFactory default setting
Password
User name When logging into the web 
screen, enter the user name 
in 1-byte alphanumeric 
characters and symbols (4 -
15 characters).root
New password When logging into the web 
screen, enter the password in 
1-byte alphanumeric 
characters and symbols (4 -
15 characters).system
Confirm new password
For confirmation, enter the 
same password that you 
entered in [New password].system
TCP/IP
DHCP Select whether to turn the 
DHCP function on or off. If the 
function is on, because the IP 
address is acquired from the 
server, it is not possible to 
enter the [IP address], 
[Subnet mask], and [Default 
gateway].OFF
IP address Enter the IP address of the 
projector in 1-byte numbers.192.168.254.254
Subnet mask Enter the subnet mask in 1-
byte numbers.255.255.255.0
Default gateway Enter the default gateway IP 
address in 1-byte numbers.0.0.0.0
If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to 
the network.
If the network subnet mask was changed, select [Subnet mask] in the above screen and 
set the new subnet mask. 
						

							Completing Computer Settings
186
Specifying Networked Multi-Projection Settings: [NMPJ Password]
From [NMPJ Password] in the settings screen, you can specify the items needed 
for NMPJ authentication. For the setting procedure, refer to “Displaying the 
Network Configuration Screen” (P181).
Setting Up Email [Mail]
From [Mail] in the settings screen, you can set the items necessary to send error 
mails and test mails. For the setting procedure, refer to “Displaying the Network 
Configuration Screen” (P181).
ItemExplanationFactory default setting
Password Enter the password for 
networked multi-projection 
authentication in single-byte 
alphanumeric characters (0-
15 characters).
Confirm password For confirmation, enter the 
same password as you 
entered in [Password]. 
						

							187
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
ItemExplanationFactory default setting
To :
Enter the recipient address for 
error mails in 1-byte 
alphanumeric characters and 
symbols (1 - 63 characters).MailUserAccount
Cc:
Enter the CC address for error 
mails in 1-byte alphanumeric 
characters and symbols (1 - 63 
characters).
From:
Enter the sender address for 
error mails in 1-byte 
alphanumeric characters and 
symbols (1 - 63 characters)[email protected]
SMTP server IP address Enter the SMTP server IP 
address in 1-byte numbers.0.0.0.0
SMTP server port number
Enter the SMTP server port 
number in 1-byte numbers (1 - 
65535).25
SNTP server IP address Enter the SNTP server IP 
address in 1-byte numbers.0.0.0.0
Time zone Select the time zone where 
the projector is used.(GMT) Dublin, Lisbon, 
London
Mail resend interval Enter the interval for 
resending mail when an error 
occurred (units: seconds) 
within the range of 0 - 59 
seconds using 1-byte 
numbers.10
Mail resend times Enter the number of times to 
resend mail when an error 
occurred within the range of 0 
- 255 using 1-byte numbers.3
Error report Select whether to turn the 
error mail sending function on 
or off.OFF 
						

							Completing Computer Settings
188
Mail Authentication Settings [Mail auth]
From [Mail auth] in the settings screen, you can configure the settings for 
authentication of mail that is sent when an error occurs. For the setting procedure, 
refer to “Displaying the Network Configuration Screen” (P181).
ItemExplanationFactory default setting
Mail authentication Select the mail authentication 
method. If OFF is selected, 
the other mail authentication 
settings cannot be changed.OFF
User name
Enter the user name to use for 
mail authentication in 1-byte 
alphanumeric characters and 
symbols (1 - 63 characters).
Password
Enter the password for mail 
authentication in 1-byte 
alphanumeric characters and 
symbols (1 - 63 characters).
Confirm password  For confirmation, enter the 
same password as you 
entered in [Password].
POP3 server IP address Enter the POP3 server IP 
address in 1-byte numbers.0.0.0.0
POP3 server port number Enter the POP3 server port 
number in 1-byte numbers (1 - 
65535).11 0
POP before SMTP response 
time
Enter the SMTP authentication 
timeout period after POP3 
authentication (units: 
milliseconds) using 1-byte 
numbers (0 - 9999 
milliseconds).300 
						

							189
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
Sending a Test Mail [Send test mail]
From [Send test mail] in the settings screen, you can send a test mail to the mail 
address that was set in [Mail]. The settings cannot be changed from this screen.
SNMP Settings [SNMP]
From [SNMP] in the settings screen, you can configure the settings related to 
control of projectors which use SNMP (Simple Network Management Protocol). For 
the setting procedure, refer to “Displaying the Network Configuration Screen” 
(P181).
ItemExplanation
To: The recipient address which was set from [Mail] in the settings screen 
(P186) is displayed.
Cc: The CC address which was set from [Mail] in the settings screen (P186) is 
displayed.
From: The sender address which was set from [Mail] in the settings screen (P186) 
is displayed.
Subject: The predetermined mail title “Canon Projector test” is displayed. 
						

							Completing Computer Settings
190
Setting Projector Information [Projector info.]
From [Projector info.] in the settings screen, you can set the names and location 
names which are used to identify projectors when multiple projectors are installed 
on the network. For the setting procedure, refer to “Displaying the Network 
Configuration Screen” (P181).
ItemExplanationFactory default setting
SNMP Select the SNMP function version. If 
OFF is selected, the SNMP function 
will be turned off and the other 
settings in this screen cannot be 
changed.OFF
Receive community Enter the community name which will 
receive projector information in 1-byte 
alphanumeric characters and symbols 
(1 - 15 characters).
Password Enter the community settings 
password in 1-byte alphanumeric 
characters and symbols (8 - 15 
characters). It can be set only when 
the SNMP version is V3.
Confirm password For confirmation, enter the same 
password as you entered in 
[Password].
ItemExplanationFactory default setting
Projector name Enter the projector name in 1-byte 
alphanumeric characters and 
symbols (1 - 63 characters).
Canon Projector001
LocationEnter the projector installation location 
in 1-byte alphanumeric characters and 
symbols (0 - 63 characters).
Some characters such as # cannot be used for [Projector name] and [Location].