Canon Projector WUX450 User Manual

							Installation-Related Menu Settings
151
Installation and Maintenance
Installation
Specifying Micro 
Digital Image Shift
> [Install settings] > [Professional 
settings] > 
[Micro-digital image 
shift]
Use this setting to fine-tune digital 
image shift.
When you have completed the 
adjustment, press the OK button to 
accept your setting and then press the 
MENU button or EXIT button.
• [Off] is the factory default.
• Select [Adjust] to fine-tune the image 
position.
Adjusting Image 
Registration
> [Install settings] > [Professional 
settings] > 
[Registration]
Adjusts colors that are out of 
alignment. You can adjust red and 
blue registration independently, 
relative to green.
When the setting is completed, press 
the OK button to accept your setting 
and then press the MENU button or 
EXIT button.
• [Off] is the factory default.
• You can adjust image registration by 
selecting [Red] or [Blue].
HDMIComponentLAN
Digital PCAnalog PCUSB
OffDoes not perform micro digital image 
shift.
AdjustPerforms micro digital image shift.
Use the [ ] / [ ] buttons for vertical 
shift.
Use the [ ] / [ ] buttons for horizontal 
shift. When you have finished 
correcting, press the OK button.
HDMIComponentLAN
Digital PCAnalog PCUSB
OffDoes not perform image registration.
AdjustPerforms image registration.
When the setting is completed, press 
the OK button. 
						

							Installation-Related Menu Settings
152
Specifying the Fan 
Mode
> [Install settings] > [Professional 
settings] > 
[Fan mode]
Enable suitable cooling by switching 
the fan mode to the setting for low- 
or high-altitude (above 2,300 m 
(7,545.8)) operation.
When the setting is completed, press 
the OK button to accept your setting 
and then press the MENU button or 
EXIT button.
• [Normal] is the factory default.
Specifying Vertical 
Projection
> [Install settings] > [Professional 
settings] > 
[Vertical projection]
You can ensure adequate cooling by 
switching the fan mode to suit 
upward- or downward-facing 
installations.
When the setting is completed, press 
the OK button to accept your setting 
and then press the MENU button or 
EXIT button.
• [Off] is the factory default.
HDMIComponentLAN
Digital PCAnalog PCUSB
NormalSetting for use in altitudes 
lower than 2,300 m (7,545.8).
High 
altitudeSetting for use in altitudes of 
2,300 m (7,545.8) or higher.
Incorrect settings may shorten the 
useful life of the lamp or other parts.
HDMIComponentLAN
Digital PCAnalog PCUSB
OffDoes not alter the fan mode.
UpwardSetting for use when the 
projector faces upward
DownwardSetting for use when the 
projector faces downward
Even if you complete this setting, 
vertical projection will result in a 
shorter useful life of the lamp and other 
parts than horizontal projection. 
						

							Installation-Related Menu Settings
153
Installation and Maintenance
Installation
Selecting the Audio In 
Terminal
> [Install settings] > [Audio in 
terminal select]
You can select the audio in terminal 
that is used for each input signal 
(HDMI, Digital PC, Analog PC-1, 
Analog PC-2, Component).
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• The factory default is as follows.
HDMI [HDMI]
Digital PC [Audio in 1]
Analog PC-1 [Audio in 1]
Analog PC-2 [Audio in 2]
Component [Audio in 2]
Adjusting Colors to 
Suit the Screen Color
> [Install settings] > [Screen color]
You can adjust the color quality of 
the images projected according to 
the color of the projection screen.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• [Normal] is the factory default.
HDMIComponentLAN
Digital PCAnalog PCUSB
OffNo audio is output.
Audio in 
1Outputs the audio signal that is 
inputted in Audio in terminal 1.
Audio in 
2Outputs the audio signal that is 
inputted in Audio in terminal 2.
HDMIOutputs the HDMI audio signal. 
(Only for HDMI)
HDMIComponentLAN
Digital PCAnalog PCUSB
NormalSelect this if a standard type of 
projection screen is used. The 
images are projected in a light 
quality similar to that of natural 
light.
GreenboardSelect this if a greenboard (dark 
green color) is used for the 
projection screen. The color quality 
similar to [Normal] is obtained on 
the greenboard.
AdjustSelect this to make detailed 
adjustment.
The following popup screen will 
appear.
Press the [ ] / [ ] buttons to 
select a color.
[ ] makes the color selected 
darker.
[ ] makes the color selected 
lighter. 
						

							Installation-Related Menu Settings
154
Specifying a Menu 
Position
> [Install settings] > [On screen] > 
[Menu position]
You can change the position of 
menus displayed.
Use the [ ] / [ ] / [ ] / [ ] buttons to 
move the menu to the desired position.
After you have moved the menu to the 
desired position, press the OK button to 
accept your setting, and then press the 
MENU or EXIT button.
Showing/Hiding the 
Guide Screen
> [Install settings] > [On screen] > 
[Guide]
You can select whether to show or 
hide the guide screen which explains 
operations.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• The factory default is [On].
• The guide screen is shown at the following 
times.
-When no input signal can be detected. 
(P145)
-When an invalid button is pressed in the 
[BLANK], [FREEZE] or [D.ZOOM] mode. 
(P76, P78)
-When the positional lock is set to [On]. 
(P146)
-When the projector is already on and the 
POWER button is pressed again.
HDMIComponentLAN
Digital PCAnalog PCUSB
HDMIComponentLAN
Digital PCAnalog PCUSB
OffHides the guide screen.
OnShows the guide screen. 
						

							Installation-Related Menu Settings
155
Installation and Maintenance
Installation
Showing/Hiding Input 
Status
> [Install settings] > [On screen] > 
[Show input status]
You can select whether the signal 
status is displayed on the screen 
when there is no signal or when 
making signal settings.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• The factory default is [On].
Showing/Hiding 
Overheat Warnings
> [Install settings] > [On screen] >
 [Overheat warning display]
You can select whether or not to 
display the [High temperature 
warning] icon when the temperature 
inside the projector has increased 
and is approaching the overheat 
temperature.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
When [On] is set, the [High temperature 
warning] icon shown below will be 
displayed when the temperature inside 
the projector is abnormally high.
• [Off] is the factory default.
HDMIComponentLAN
Digital PCAnalog PCUSB
OffThe input status is not displayed.
OnThe input status is displayed.
HDMIComponentLAN
Digital PCAnalog PCUSB
OffThe [High temperature warning] icon is 
not displayed.
OnThe [High temperature warning] icon is 
displayed.
Screen 
						

							Installation-Related Menu Settings
156
Specifying the Menu 
Display Time
> [Install settings] > [On screen] > 
[Menu display time]
The setting for the menu display 
time can be extended from the 
normal 10 or 30 seconds to 3 
minutes.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• [Normal] is the factory default.
• The following display and operation are also 
changed.
Showing/Hiding Lamp 
Replacement 
Warnings
> [Install settings] > [On screen] >
[Lamp warning display]
A message that advises you to 
change the lamp can be set to 
display when the lamp has been 
used for the specified period of time.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• The factory default is [On].
HDMIComponentLAN
Digital PCAnalog PCUSB
NormalThe menu is displayed for 10 
or 30 seconds.
ExtendedThe menu is displayed for 3 
minutes.
Item [Normal]
[Extended]
The display time of the 
following screens
- MENU screen30 
seconds3 
minutes
- Input (P54)
- Keystone adjustment 
(P68)
- Keystone reset (P70)
- D.image shift 
adjustment (P63, P64)
- D.image shift reset 
(P65)
- Aspect (P67)
- Image Mode (P71)
- Volume adjustment 
(P77)
- Gamma correction 
(P100)10 
seconds3 
minutes
HDMIComponentLAN
Digital PCAnalog PCUSB
OnThe prepare lamp message and the 
lamp warning are displayed.
OffThe prepare lamp message and the 
lamp warning are not displayed.
When it is time to replace the lamp, 
the LAMP indicator on the projector 
will flash, and lamp replacement 
(P202) is recommended at this time. 
						

							Installation-Related Menu Settings
157
Installation and Maintenance
Installation
Showing/Hiding Filter 
Cleaning Warnings
> [Install settings] > [On screen] > 
[Air filter warning display]
A message advising you to perform 
cleaning can be set to display when 
the filter needs cleaning.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• The factory default is [On].
Showing/Hiding Split-
Screen ID
> [Install settings] > [On screen] >
[Split screen ID display]
Specify whether to show or hide the 
digit (1 or 2) that identifies screens in 
split-screen mode. Note that even if 
you select [Off], a marker will be 
displayed in the corner of the screen 
to identify the screen that has 
control rights.
When you have completed the 
adjustment, press the OK button to 
accept your setting and then press the 
MENU button or EXIT button.
• The factory default is [On].
HDMIComponentLAN
Digital PCAnalog PCUSB
Off
The air filter warning is not displayed.
OnThe air filter warning is displayed.
HDMIComponentLAN
Digital PCAnalog PCUSB
OffHides the screen ID.
OnShows the screen ID. 
						

							Installation-Related Menu Settings
158
Showing/Hiding the 
Test Pattern
> [Install settings] > [Test pattern]
You can project a test pattern (P291) 
to check resolution, color, and other 
details even without supplying an 
input signal.
Press the OK button to accept your 
setting and then press the MENU 
button or EXIT button.
• [Off] is the factory default.
• During test pattern display, you can use the 
[ ] / [ ] buttons to switch test patterns. 
Additionally, if a test pattern has option 
settings, you can change the settings using 
the [ ] / [ ] buttons. (P291)
• The test pattern can also be displayed or 
turned off by pressing the TEST PATTERN 
button on the remote control.
HDMIComponentLAN
Digital PCAnalog PCUSB
OffThe test pattern is not displayed.
OnDisplays the test pattern. 
						

							Installation-Related Menu Settings
159
Installation and Maintenance
Installation
Projecting from Multiple Projectors at Once 
(Edge Blending)
> [Install settings] > [Professional 
settings] > 
[Edge blending]
Overlapping edges of images from 
multiple projectors used together 
can be blended to make the overall 
image more seamless.
■Basic Instructions
Follow these steps when using two projectors side by side.
1In the [Install settings] menu, select [Professional settings] > [Edge 
blending].
2Select [Adjust].
The edge blending window is displayed.
HDMIComponentLAN
Digital PCAnalog PCUSB 
						

							Installation-Related Menu Settings
160
Here, you can use the following settings in the edge blending menu.
3Select the position where the images overlap.
When you are adjusting the left image, this area is along the right edge of the 
image. In the edge blending window, select [Right] > [Adjust].
4Set [Marker] to [On].
Marker lines are projected on the images. The red marker indicates the start 
position for adjustment, and the green marker, the end position.
OffDoes not blend overlapping areas.
AdjustDisplays the menu for blending overlapping 
areas.
Left, Right, Top, Bottom
Off Projects an image with no correction.
Adjust Marker Off Hides the markers.
On Displays markers showing the adjustable 
blending area, with one line indicating the start 
position (in red) and another, the end position (in 
green).
Start position Moves the marker for the start position.
Width Specifies the width between the start and end 
markers.
Reset Resets the marker settings.
Black level adjustmentAdjusts the black level of non-overlapping image 
areas. (P162)
ResetResets any adjustments you have made.
• If you have already completed edge blending settings, selecting [Adjust] will apply 
them.
• To restore the default settings before adjustment, select [Reset].
By default, the green and red markers are displayed in the same position, so only the red 
marker is visible.
Overlapping area Left image Right image