Canon Projector WUX450 User Manual
Have a look at the manual Canon Projector WUX450 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 186
Completing Computer Settings
186
Specifying Networked Multi-Projection Settings: [NMPJ Password]
From [NMPJ Password] in the settings screen, you can specify the items needed
for NMPJ authentication. For the setting procedure, refer to “Displaying the
Network Configuration Screen” (P181).
Setting Up Email [Mail]
From [Mail] in the settings screen, you can set the items necessary to send error
mails and test mails. For the setting procedure, refer to “Displaying the Network
Configuration Screen”...](http://img.usermanuals.tech/thumb/14/99365/w64_projector_manual_7685_d-185.png "Page 186
Completing Computer Settings
186
Specifying Networked Multi-Projection Settings: [NMPJ Password]
From [NMPJ Password] in the settings screen, you can specify the items needed
for NMPJ authentication. For the setting procedure, refer to “Displaying the
Network Configuration Screen” (P181).
Setting Up Email [Mail]
From [Mail] in the settings screen, you can set the items necessary to send error
mails and test mails. For the setting procedure, refer to “Displaying the Network
Configuration Screen”...")
![Page 188
Completing Computer Settings
188
Mail Authentication Settings [Mail auth]
From [Mail auth] in the settings screen, you can configure the settings for
authentication of mail that is sent when an error occurs. For the setting procedure,
refer to “Displaying the Network Configuration Screen” (P181).
ItemExplanationFactory default setting
Mail authentication Select the mail authentication
method. If OFF is selected,
the other mail authentication
settings cannot be changed.OFF
User name
Enter the user...](http://img.usermanuals.tech/thumb/14/99365/w64_projector_manual_7685_d-187.png "Page 188
Completing Computer Settings
188
Mail Authentication Settings [Mail auth]
From [Mail auth] in the settings screen, you can configure the settings for
authentication of mail that is sent when an error occurs. For the setting procedure,
refer to “Displaying the Network Configuration Screen” (P181).
ItemExplanationFactory default setting
Mail authentication Select the mail authentication
method. If OFF is selected,
the other mail authentication
settings cannot be changed.OFF
User name
Enter the user...")
![Page 189
189
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
Sending a Test Mail [Send test mail]
From [Send test mail] in the settings screen, you can send a test mail to the mail
address that was set in [Mail]. The settings cannot be changed from this screen.
SNMP Settings [SNMP]
From [SNMP] in the settings screen, you can configure the settings related to
control of projectors which use SNMP (Simple Network Management Protocol). For
the setting procedure, refer to...](http://img.usermanuals.tech/thumb/14/99365/w64_projector_manual_7685_d-188.png "Page 189
189
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
Sending a Test Mail [Send test mail]
From [Send test mail] in the settings screen, you can send a test mail to the mail
address that was set in [Mail]. The settings cannot be changed from this screen.
SNMP Settings [SNMP]
From [SNMP] in the settings screen, you can configure the settings related to
control of projectors which use SNMP (Simple Network Management Protocol). For
the setting procedure, refer to...")
![Page 190
Completing Computer Settings
190
Setting Projector Information [Projector info.]
From [Projector info.] in the settings screen, you can set the names and location
names which are used to identify projectors when multiple projectors are installed
on the network. For the setting procedure, refer to “Displaying the Network
Configuration Screen” (P181).
ItemExplanationFactory default setting
SNMP Select the SNMP function version. If
OFF is selected, the SNMP function
will be turned off and the other...](http://img.usermanuals.tech/thumb/14/99365/w64_projector_manual_7685_d-189.png "Page 190
Completing Computer Settings
190
Setting Projector Information [Projector info.]
From [Projector info.] in the settings screen, you can set the names and location
names which are used to identify projectors when multiple projectors are installed
on the network. For the setting procedure, refer to “Displaying the Network
Configuration Screen” (P181).
ItemExplanationFactory default setting
SNMP Select the SNMP function version. If
OFF is selected, the SNMP function
will be turned off and the other...")
![Page 191
191
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
Setting PJLink [PJLink]
From [PJLink] in the settings screen, you can set the PJLink functions which are the
standard for projector management on a network. For the setting procedure, refer
to “Displaying the Network Configuration Screen” (P181). For information about
PJLink, refer to “What is PJLink?” (P176).
Setting Up a Controller Manufactured by Crestron Electronics
[Crestron Controller]
From [Crestron...](http://img.usermanuals.tech/thumb/14/99365/w64_projector_manual_7685_d-190.png "Page 191
191
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
Setting PJLink [PJLink]
From [PJLink] in the settings screen, you can set the PJLink functions which are the
standard for projector management on a network. For the setting procedure, refer
to “Displaying the Network Configuration Screen” (P181). For information about
PJLink, refer to “What is PJLink?” (P176).
Setting Up a Controller Manufactured by Crestron Electronics
[Crestron Controller]
From [Crestron...")
![Page 193
193
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
Resetting Network Settings to the Default Settings
1Perform steps 1 - 3 on “Displaying the Network Configuration Screen”
(P181) to display the settings screen.
2Click [Initialize].
3A confirmation window appears. Click [OK].](http://img.usermanuals.tech/thumb/14/99365/w64_projector_manual_7685_d-192.png "Page 193
193
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
Resetting Network Settings to the Default Settings
1Perform steps 1 - 3 on “Displaying the Network Configuration Screen”
(P181) to display the settings screen.
2Click [Initialize].
3A confirmation window appears. Click [OK].")
![Page 195
195
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
Control via the Web Screen
When the projector is connected to a network, it is possible to control the projector
from a computer via the network.
1Turn on the computer and projector.
2Launch a web browser, enter “http://(projector IP address)” in the
address bar, and press the Enter key.
The projector web screen appears.
3Click [Projector control] on the web screen.
The password input window appears.
4Enter the user...](http://img.usermanuals.tech/thumb/14/99365/w64_projector_manual_7685_d-194.png "Page 195
195
Completing Computer Settings
Installation and Maintenance
Connecting to a Network
Control via the Web Screen
When the projector is connected to a network, it is possible to control the projector
from a computer via the network.
1Turn on the computer and projector.
2Launch a web browser, enter “http://(projector IP address)” in the
address bar, and press the Enter key.
The projector web screen appears.
3Click [Projector control] on the web screen.
The password input window appears.
4Enter the user...")
![Page 196
Completing Computer Settings
196
5When the operations are finished, click [Back to top] to return the initial
web screen.
ItemExplanation
Projector name The name of the connected projector is displayed. (P190)
IP address The IP address of the connected projector is displayed. (P195)
Refresh Refreshes the displayed contents with the most recent information.
Power Turns projector power on or off.
Input Select an input signal and click [Apply] to change to that input
signal. (P53)
Aspect Select an aspect...](http://img.usermanuals.tech/thumb/14/99365/w64_projector_manual_7685_d-195.png "Page 196
Completing Computer Settings
196
5When the operations are finished, click [Back to top] to return the initial
web screen.
ItemExplanation
Projector name The name of the connected projector is displayed. (P190)
IP address The IP address of the connected projector is displayed. (P195)
Refresh Refreshes the displayed contents with the most recent information.
Power Turns projector power on or off.
Input Select an input signal and click [Apply] to change to that input
signal. (P53)
Aspect Select an aspect...")
191 Completing Computer Settings Installation and Maintenance Connecting to a Network Setting PJLink [PJLink] From [PJLink] in the settings screen, you can set the PJLink functions which are the standard for projector management on a network. For the setting procedure, refer to “Displaying the Network Configuration Screen” (P181). For information about PJLink, refer to “What is PJLink?” (P176). Setting Up a Controller Manufactured by Crestron Electronics [Crestron Controller] From [Crestron Controller] in the settings screen, you can set parameters for communication via controllers manufactured by Crestron Electronics. ItemExplanationFactory default setting PJLink Turn the PJLink function on or off. If OFF is selected, the PJLink function will be turned off and the other settings in this screen cannot be changed.ON PJLink authentication Select whether to turn the PJLink authentication function on or off. If OFF is selected, [Password] and [Confirm password] cannot be changed.ON Password Enter the PJLink authentication password in 1-byte alphanumeric characters (1 - 32 characters).system Confirm password For confirmation, enter the same password that you entered in [Password].system
Completing Computer Settings 192 Setting Errors When a setting-related error occurs, the error name is displayed on the screen, and a “!” mark is displayed next to the input field which caused the error. The error meanings are as shown below. ItemExplanationFactory default setting IP ID Specify the controller’s IP ID. 3 IP address Specify the controller’s IP address. 127.0.0.1 Port number Specify the controller’s port number. 41794 ErrorMeaning Input error A setting outside the valid range was set on the settings screen. Password setting error The set password and confirmation password did not match. Invalid SMTP The SMTP server IP address has not been set. System failed to connect SMTP server. Failed to connect to the SMTP server when sending a test mail. System failed to connect POP3 server. Failed to connect to the POP3 server attempting to send a test mail. System doesn’t support this auth type. An authentication type was set which is not supported by the server. System failed to authenticate. Authentication failed attempting to send a test mail. The system failed to send the test mail. Sending of test mail failed due to a connection failure with the SMTP server or an error which does not ordinarily occur. Unknown error Unknown error
193 Completing Computer Settings Installation and Maintenance Connecting to a Network Resetting Network Settings to the Default Settings 1Perform steps 1 - 3 on “Displaying the Network Configuration Screen” (P181) to display the settings screen. 2Click [Initialize]. 3A confirmation window appears. Click [OK].
Completing Computer Settings 194 ■Error Notification Mails The messages shown in the following error list are sent when an error occurs in the projector. Error list Errors related to temperatureError name Temperature abnormality Text The temperature inside the projector is too high for some reason or the outside air temperature is higher than the specified one. If the problem is inside the projector, check whether the projector is installed and operated normally, turn off the projector to cool its inside, and retry projection. If the same warning occurs again, the projector may be defective. Contact your dealer. Errors related to the lampError name Faulty lamp Text The lamp has burnt out. Replace the lamp with a new one. If the same warning occurs again, the lamp drive circuit may be defective. Contact your dealer. Errors related to the fanError name Faulty cooling fan Text The cooling fan or another component may be defective. Contact your dealer. Errors related to the air filterError name Faulty air filter unit Text The air filter unit is not installed properly. Check whether the air filter unit is installed properly. If it is installed properly, the air filter unit detection switch may be defective. Contact your dealer. Errors related to the powerError name Faulty power supply Text The voltage of part of the power supply is abnormally high or any other problem has occurred in the power supply. Contact your dealer.
195 Completing Computer Settings Installation and Maintenance Connecting to a Network Control via the Web Screen When the projector is connected to a network, it is possible to control the projector from a computer via the network. 1Turn on the computer and projector. 2Launch a web browser, enter “http://(projector IP address)” in the address bar, and press the Enter key. The projector web screen appears. 3Click [Projector control] on the web screen. The password input window appears. 4Enter the user name and password on the password input window, then click [OK]. The factory default user name is “root” and the password is “system”. [Projector control] screen appears. The projector control screen appears. The projector can be controlled from this screen. The factory default IP address is “192.168.254.254”. If DHCP settings are used, ask the network administrator for the projector IP address. It is possible to check the IP address from the projector menu.
Completing Computer Settings 196 5When the operations are finished, click [Back to top] to return the initial web screen. ItemExplanation Projector name The name of the connected projector is displayed. (P190) IP address The IP address of the connected projector is displayed. (P195) Refresh Refreshes the displayed contents with the most recent information. Power Turns projector power on or off. Input Select an input signal and click [Apply] to change to that input signal. (P53) Aspect Select an aspect and click [Apply] to change to that aspect. (P66) Image mode Select an image mode and click [Apply] to change to that image mode. (P71) Blank Switches the blank setting on or off. (P76) Mute Switches the mute setting on or off. (P77) Auto PC Click [Apply] to perform Auto PC adjustment. (P57) Split screen Select the setting for split-screen mode and click [Apply] to switch to split-screen projection. Split screen control Select the control rights setting for split-screen mode and click [Apply] to switch the side currently under control. Information The control results and control error information are displayed at the top of the screen.
197 Table of Contents Safety Instructions Before Use Operation Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation and Maintenance Installation Connecting to a Network Maintenance Networked Multi-Projection Networked Multi-Projection Overview Operation in Each Mode Functions in All Modes AppendixOther Information Index Maintenance
198 Cleaning the Projector Clean the projector frequently to prevent dust from settling on the surface. A dirty lens may ruin the quality of the projected image. Wipe the projector’s main unit softly with a soft cloth. If the projector is heavily soiled, soak the cloth in water with a small amount of detergent in it, squeeze the cloth thoroughly, and then wipe the projector with it. After cleaning, wipe the projector with a dry cloth. When cleaning the projector, make sure to turn off the projector, wait until the cooling fan stops, disconnect the power plug from the electrical outlet, and let the projector stand for at least 1 hour. Otherwise, you may get burned because the main unit is very hot immediately after the projector is turned off. • Never use volatile cleaning liquid or benzine, as these may damage the finish of the projector. • When using a chemical dust cloth, make sure to read the instructions thoroughly. • When cleaning the projector’s lens, use a commonly available air blower or lens cleaning paper. The lens surface is easily damaged, so do not use a hard cloth or tissues.
199 Installation and Maintenance Maintenance Cleaning and Replacing the Air Filter Replacing the Air Filter Follow the procedure below when replacing the air filter. 1Turn off the projector power and remove the power plug. 2As you press the top and bottom of the air filter cover to release the lock, remove the cover. 3Open the filter cover and remove it. 4Remove the air filter.
Cleaning and Replacing the Air Filter 200 5Follow this procedure in reverse to install a new air filter. Cleaning the Air Filter The air filter protects the lens and mirror inside the projector from dust and dirt. Should the air filter become clogged with dust, the projector may be damaged since it will block the air flow into the projector and raise the internal temperature of the projector. The following screen is displayed when turning on the projector if the air filter needs to be cleaned (after approx. 300 hours). Clean the air filter if it is displayed. •Turn the power of the projector off and pull out the power plug. •Hook your finger around the air filter handle on the front of the projector and remove the air filter. Use a vacuum cleaner to clean off the dust. •If the air filter cleaning screen is displayed when turning on the projector after cleaning the air filter, select [Yes] and press the OK button. The air filter cleaning screen will disappear. •This screen is not displayed when [Air filter warning display] is set to [Off]. (P157) • Handle the air filter carefully. If damaged, the air filter will not work properly. • When the lamp is replaced, it is recommend that you also clean or replace the air filter. • Contact the Canon Customer Support Center for further information. • Replacement air filter part number: RS-FL02 • This can also be purchased from the Canon website. • Only the [ ], [ ], OK and POWER buttons are available while this screen is displayed. (When you press the POWER button, the “Push POWER button again to turn off power.” message appears.) • When this screen has disappeared after being displayed for 10 seconds, all buttons become operable. Do not rinse the air filter in water, which may damage the air filter and projector.