Canon printer imageCLASS D1170 User Manual

							xx
Legal Notices
Legal Notices
Users in the U.S.A.
Pre-Installation Requirements for Canon Facsimile Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine. See Chapter 14, “Appendix,” for specific 
dimensions and weight.
B.

  Order Information
1. A single telephone line (touch-tone or rotary) should be used.
2.  Order an RJ11-C telephone wall jack (USOC), which should be installed by the telephone company. If 
the RJ11-C wall jack is not present, telephone/facsimile operation is not possible.
3.

  Order a normal business line from your telephone company’s business r\
epresentative. The line 
should be a regular voice grade line or an equivalent one. Use one line per unit.
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if you communicate overseas
Canon recommends an individual line following industry standards, i.e., 2,500 (touch-tone) or 500 (rotary/pulse dial) telephones. A 
dedicated extension off a PBX (Private Branch eXchange) unit without “Call Waiting” can be used with your facsimile unit. Key telephone 
systems are not recommended because they send nonstandard signals to individual telephones for ringing and special codes, which 
may cause a facsimile error.
C.  Power Requirements
The machine should be connected to a standard 120 volt AC, three-wire grounded outlet only.
Do not connect this machine to an outlet or power line shared with other appliances that cause 
“electrical noise.” Air conditioners, electric typewriters, copier\
s, and machines of this sort generate 
electrical noise that often interferes with communications equipment and\
 the sending and receiving of 
documents. 
						

							xx
Legal Notices
Legal Notices
Connection of the Equipment
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the 
rear panel of this equipment is a label that contains, among other information, a product identifier in the 
format of US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
The REN (Ringer Equivalence Number) is used to determine the number of devices that may be connected to 
a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an 
incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the 
number of devices that may be connected to a line, as determined by the total RENs, contact the local 
telephone company. The REN for this product is part of the product identifier that has the format US:
AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 10 is a REN of 1.0).
An FCC compliant telephone line cable and modular plug is provided with this equipment. This equipment is 
designed to be connected to the telephone network or premise wiring using a compatible modular jack that 
is Part 68 compliant.
This equipment may not be used on coin service provided by the telephone company. Connection to party 
lines is subjected to state tariffs.
In Case of Equipment Malfunction
Should any malfunction occur which cannot be corrected by the procedures described in this guide or the e-
Manual, disconnect the equipment from the telephone line cable and disconnect the power cord.
The telephone line cable should not be reconnected or the main power switch turned ON until the problem is 
completely resolved. Users should contact Canon Authorized Service Facilities for servicing of equipment, 
Information regarding Authorized Service Facility locations can be obtained by calling Canon Customer Care 
Center (1-800-OK-CANON). 
						

							xx
Legal Notices
Legal Notices
Rights of the Telephone Company
If this equipment (imageCLASS D1180/D1170/D1150/D1120) causes harm to the telephone network, the 
telephone company may temporarily disconnect service. The telephone company also retains the right to 
make changes in facilities and services that may affect the operation of this equipment. When such changes 
are necessary, the telephone company is required to give adequate prior notice to the user.
However, if advance notice is not possible, the telephone company will notify the customer as soon as 
possible. Also, the customer will be advised of his/her right to file a complaint with the FCC if he/she believes 
it is necessary.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, 
including FAX machines, to send any message unless such message clearly contains in a margin at the top or bottom of each 
transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other ent\
ity, 
or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. 
( The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance 
transmission charges.)
In order to program this information into your machine, you should complete the procedure for registering your name, unit’s telephone 
number, time, and date in the Starter Guide.
Users in Canada
Pre-Installation Requirements for Canon Facsimile Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine. See Chapter 14, “Appendix,” for specific 
dimensions and weight.
B.

  Order Information
1. A single telephone line (touch-tone or rotary) should be used.
2.  Order a CA11A modular jack, which should be installed by the telephone company. If the CA11A jack 
is not present, installation cannot occur.
3.

  Order a normal business line from your telephone company’s business r\
epresentative. The line 
should be a regular voice grade line or an equivalent one. Use one line per unit.
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if you communicate overseas
Canon recommends an individual line following industry standards, i.e., 2,500 (touch-tone) or 500 (rotary/pulse dial) telephones. A 
dedicated extension off a PBX (Private Branch eXchange) unit without “Call Waiting” can be used with your facsimile unit. Key telephone 
systems are not recommended because they send nonstandard signals to individual telephones for ringing and special codes, which 
may cause a facsimile error. 
						

							xx
Legal Notices
Legal Notices
C. Power Requirements
The power outlet should be a three-prong grounded receptacle (Single or Duplex). It should be 
independent from copiers, heaters, air conditioners, or any electric equipment that is thermostatically 
controlled. The rated value is 115 volts and 15 amperes. The CA11A modular jack should be relatively 
close to the power outlet to facilitate installation.
Notice This product meets the applicable Industry Canada technical specifications.
The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be 
connected to a telephone interface. The termination of an interface may consist of any combination of 
devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.
The REN of this product is 1.0.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities 
of the local telecommunications company. The equipment must also be installed using an acceptable 
method of connection. In some cases, the company’s inside wiring associated with a single line individual 
service may be extended by means of a certified connector assembly (telephone extension cord). The 
customer should be aware that compliance with the above conditions may not prevent deterioration of 
service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated 
by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, 
may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, 
telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution 
may be particularly important in rural areas.
Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or 
electrician, as appropriate.
This equipment complies with the Canadian ICES-003 Class B limits.
–
–
–
–
–
– 
						

							xxv
Legal Notices
Legal Notices
Utilisation au Canada
Conditions à Remplir Préalablement à L’installation d’un Télécopieur Canon
A. Emplacement
Prévoir une table, un meuble, ou un bureau suffisamment solide et de taille appropriée (voir le chapitre 
15, Annexe (Appendix), pour les indications de poids et dimensions).
B.

  Installation téléphonique
1. Une seule ligne téléphonique (tonalités ou impulsions) doit ê\
tre utilisée.
2.  Il faut commander un jack modulaire CA11A qui sera installé par la co\
mpagnie téléphonique. Sans 
ce jack, la mise en place serait impossible.
3.

  Si vous vous abonnez à une nouvelle ligne, demandez une ligne d’affaires normale de qualité 
téléphonique courante ou équivalente. Prenez un abonnement d’une ligne par appareil.
Ligne automatique interurbaine
ou
Ligne automatique internationale (si vous communiquez avec les pays é\
trangers)
Canon vous conseille d’utiliser une ligne individuelle conforme aux normes industrielles, à savoir:
ligne téléphonique 2,500 (pour appareil à clavier) ou 500 (pour appareil à cadran/impulsions). Il est également possible de raccorder ce 
télécopieur à un système téléphonique à poussoirs car la plupart de ces systèmes émettent des signaux d’appel non normalisés ou des 
codes spéciaux qui risquent de perturber le fonctionnement du télécopieur.
C.  Condition d’alimentation
Raccordez le télécopieur à une prise de courant plus terre à\
 trois branches, du type simple ou double, et 
qui ne sert pas à alimenter un copieur, un appareil de chauffage, un climatiseur ou tout autre appareil 
électrique à thermostat.
L’alimentation doit être de 115 volts et 15 ampères. Pour facil\
iter l’installation, le jack CA11A doit être 
assez proche de la prise de courant. 
						

							xxv
Legal Notices
Legal Notices
RemarquesLe présent matériel est conforme aux spécifications techniques applicables d’Industrie Canada.
Avant d’installer cet appareil, l’utilisateur doit s’assurer qu’il est permis de le connecter à l’équipement de la 
compagnie de télécommunication locale et doit installer cet appareil en utilisant une méthode de 
connexion autorisée. Il se peut qu’il faille étendre la circuiterie intérieure de la ligne individuelle d’abonné, 
qui a été installée par la compagnie, au moyen d’un jeu de connecteurs homologués (rallonge 
téléphonique).
L’attention de l’utilisateur est attirée sur le fait que le respect des conditions mentionnées ci-dessus ne 
constitue pas une garantie contre les dégradations de qualité du service dans certaines circonstances.
L’indice d’équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de terminaux qui peuvent être 
raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison 
quelconque de dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous 
les dispositifs n’excède pas 5.
Le nombre d’équivalents sonnerie (REN) de ce produit est 1,0.
Les réparations sur un appareil certifié doivent être faites par une société d’entretien canadienne autorisée 
par le Gouvernement canadien et désignée par le fournisseur. Toute réparation ou modification que 
pourrait faire I’utilisateur de cet appareil, ou tout mauvais fonctionnement, donne à la compagnie de 
télécommunication le droit de débrancher I’appareil.
Pour sa propre protection, I’utilisateur doit s’assurer que les prises de terre de I’appareil d’alimentation, les 
lignes téléphoniques et les tuyaux métalliques internes, s’il y en a, sont bien connectés entre eux. Cette 
précaution est particulièrement importante dans les zones rurales.
Au lieu d’essayer de faire ces branchements eux-mêmes, les utilisateurs sont invités à faire appel à un service d’inspection faisant autorité
en matière d’électricité ou à un électricien, selon le cas.
Respecte les limites de la classe B de la NMB-003 du Canada.
–
–
–
–
–
–
– 
						

							
xxvi
Laser Safety
  Laser  Safety  
      La se r S afe ty  Laser Safety 
 This machine complies with 21 CFR Chapter 1 Subchapter J as a Class 1 laser product under the U.S. 
Department of Health and Human Services (DHHS) Radiation Performance Standard according to the 
Radiation Control for Health and Safety Act of 1968. This means that the machine does not produce hazardous 
radiation. 
 Since radiation emitted inside the machine is completely confined within protective housings and external 
covers, the laser beam cannot escape from the machine during any phase of user operation. 
 C D RH  R eg ula tio n s  CDRH  Regulations 
 The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration 
implemented regulations for laser products on August 2, 1976. These regulations apply to laser products 
manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States. 
   Use of controls, adjustments, or performance of procedures other than those specified in this manual may result in hazardous r adiation 
exposure. 
  
 The label is attached to the laser scanner machine inside the machine and is not in a user access area. 
  



This machine is confirmed as the class 1 laser product in IEC60825-1:2007. 
						

							Before Using the Machine
1
Before Using the 
Machine
This chapter describes what you should know before using this machine, such as the names of the parts and their 
functions, and basic settings to use various functions.
Machine Components ................................................. 1-2
External View (Front)  ..........................................................1-2
External View (Back)  ............................................................1-4
Internal View   ........................................................................\
.1-5
Operation Panel  ........................................................... 1-6
Main Operation Panel  ........................................................1-6
Send Operation Panel  ..................................................... 1-10
Display (Standby Mode)  ............................................1-12
Copy Mode  ........................................................................\
.. 1-12
Send Mode/Fax Mode  ..................................................... 1-12
Scan Mode  ........................................................................\
... 1-12
Log In Mode  ........................................................................\
 1-13
Toner Cartridge  ..........................................................1-14
Maintaining the Toner Cartridge  ................................. 1-15
Entering Characters  ...................................................1-16
Telephone Line Settings (D1180/D1170/D1150)  ....1-17
Timer Settings  ............................................................1-18
Setting the Sleep Mode  .................................................. 1-18
Setting the Auto Clear Time  .......................................... 1-19
Setting the Daylight Saving Time  ............................... 1-19   
						

							Before Using the Machine
1-2
Machine Components
Machine Components
This section describes the parts names of the machine and their functions.
External View (Front) 
						

							Before Using the Machine
1-3
Machine Components
①ADF (Automatic Document Feeder)Holds documents and feeds them automatically 
into the scanning area.
②Slide guides Adjust to the width of the document.
③Document feeder tray Holds documents.
④Document delivery tray Receives documents.
⑤Operation panel Controls the machine.
⑥Multi-purpose tray Feeds non-standard size or thick/thin type paper 
stacks.
⑦Multi-purpose tray extension  Pull out to load paper stack.
⑧Slide guides for multi-purpose tray Adjusts to the width of the paper.
⑨Paper stopper Lift the paper stopper to prevent the paper from 
falling off the output tray.  ⑩Output tray
Receives copies, prints and faxes. Outputs paper 
with the printed side facing down.
⑪Scanning platform Open this platform to clear paper jams.
⑫Open button Push to open the front cover.
⑬Front cover Open this cover to replace the toner cartridge or 
to clear paper jams.
⑭ Main power switch Turns the power ON or OFF.
⑮Paper cassette Holds up t
 o 500 sheets of paper (21 lb (80 g/m
2)).
⑯Cassette Feeding Module-U1 (Optional) Holds the additional paper supply. Up to 500 
sheets of paper (21 lb (80 g/m
2)) can be held.