Canon Imageprograf Ipf825 User Guide

6.
Open the Top Cover, and if there is a paper jam at the position shown, push it inside with your fingers. The paper will drop to the floor or to the lower part of the printer.
Note
• If paper remains in the lower part of the printer, push it to the floor with your fingers.
• If 
the paper does not drop to the floor or to the lower part of the printer, fold an A4 sheet three times,
insert it through the gap of the Platen (a) and the Paper Retainer (b), and push the jammed paper out. Troubleshooting 
>...

7.
Lower the Release Lever and close the Top Cover. 8.
In a crouching position, push the Roll Unit in. 9.
Position the Wheeled Output Stacker by the printer.   (See "Using the Wheeled Output Stacker.") →P.671
10. Turn the printer on.   (See "Turning the Printer On and Off.") →P.702
Roll Paper Cannot be Inserted into the Paper Feed Slot
Cause
Corrective Action
The roll paper is warped. Straighten out curls and reload the roll.
If paper cannot be advanced from Roll 2 (Lower),
the Roll Unit...

Cannot Load Sheets
Cause
Corrective Action
The paper source selection is incorrect. Press the Feeder Selection  button to activate the Cut Sheet lamp.Paper is not cut straight
Cause
Corrective Action
The paper is bent or curled at the cut position. Straighten out any curling by the edges of the paper.
Paper rises by the ends of the cut position before it is cut. Reload the paper correctly. Paper is not cut
Cause
Corrective Action
In the printer driver,  No or Print Cut Guideline is specified
in Auto Cut....

Printing does not start
The Data lamp on the Control Panel does not light up .................................................................................... 858
The printer does not respond even if print jobs are sent .................................................................................858
 
Ink Filling.. is displayed ................................................................................................................................... 858
The display screen indicates...

The display screen indicates Agitating
Cause
Corrective Action
Ink agitation is in
progress. The time for agitation varies depending on how long the printer has been turned off. (Between
about a minute and a half to twenty minutes.) During agitation, you can print or do other opera-
tions after the printer goes  Online. Troubleshooting > Printing does not start >
iPF825
The display screen indicates Agitating 12
859
 

The printer stops during a print job
An error message is shown on the Display Screen ......................................................................................... 860
The printer ejects blank, unprinted paper ........................................................................................................ 860
  An error message is shown on the Display Screen
Status
Corrective Action
An error message is displayed during printing. Check the error message and take action as necessary....

Problems with the printing quality
Printing is faint ................................................................................................................................................. 861
Paper rubs against the printhead .................................................................................................................... 862
The edges of the paper are dirty ........................................................................................................................

Cause
Corrective Action
Printing may be faint if  Print Qual-
ity in Advanced Settings in the
printer driver is set to  Standard or
Draft.  (See "Giving Priority to Particular Graphic Elements and Colors for Print-
ing .") →P.56
Paper rubs against the printhead
Cause
Corrective ActionThe type of paper specified in the
printer driver does not match the
type loaded in the printer.
Load paper of the same type as you have specified in the printer driver.
 (See "Loading Rolls in the Printer...

The edges of the paper are dirty
Cause
Corrective Action
The Platen has become dirty after
borderless printing or printing on
small paper. Open the Top Cover and clean the Platen.
 (See "Cleaning Inside the Top Cover .") →P.833
The paper type as specified on the
printer does not match the type
specified in the printer driver.
Make sure the same paper type is specified on the printer as in the printer driver.
 (See "Selecting the Paper Type (Roll) .") →P.642
 (See "Selecting the Paper...

Cause
Corrective ActionYou are using a paper that
does not dry easily.
In this case, in the Control Panel menu, complete the settings for 
Dry time and Area
in Scan Wait Time .
However, note that printing will now take longer.  (See "Main Menu Settings.") →P.730
The back side of the paper is dirty
Cause
Corrective ActionThe Platen has become dirty after borderless print-
ing or printing on small paper.
Open the Top Cover and clean the Platen.
 (See "Cleaning Inside the Top Cover .")...