Canon Imageprograf Ipf815 Mfp M40 User Guide
Have a look at the manual Canon Imageprograf Ipf815 Mfp M40 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Information Setting Item Description, InstructionsSystem Info FirmwareDisplays the version of the printer and firmware. Boot Displays the version of the boot ROM. MIT Displays the version of the MIT database format. s/n Displays the printer's serial number. MAC Displays the MAC address. IP Displays the IP address. HDDSpace Displays the space available on the printer's hard disk.Error Log 1: xxxxxxxx-xxxx Displays the two most recent error message numbers, most recent first. 2: xxxxxxxx-xxxx Submenu Display Press the Information button to display this information, one after another: the Maintenance Cartridge capacity and remain- ing ink levels, paper information, printer information, and HP-GL/2 settings information. Each time you press the Information button, the following submenus are displayed. Note • Press any button other than the Information button to restore the previous mode. • After you display a submenu, the printer will revert to the previous mode in about ten seconds if no print job is received or if you do not operate the printer. Remaining Maintenance Cartridge capacity and ink levels The remaining Maintenance Cartridge capacity is shown on the top level of the Display Screen. The remaining level of each ink is shown on the bottom level of the Display Screen. Ink levels shown on the Display Screen correspond to the inks identified by the color labels on the bottom of the Display Screen. These symbols may be displayed above the ink level: ! if ink is low, × if no ink is left, and ? if ink level detection is not on. Remaining ink is indicated as follows. Printer Parts > Control Panel > iPF815 Submenu Display 9 735
Information on the loaded paper Here, the paper size, type, and related printer settings are displayed. Printer information Displays the firmware version, serial number, free hard disk space, IP address, and interface information. HP-GL/2 setting information HP-GL/2 settings information is displayed on three screens. Status Print You can print a Status Print report indicating the current status of the printer. With Status Print, information is printed regarding the printer firmware version, various settings, and the utilization level of consumables. Printing Status Print Reports 1. Load paper. If using sheets, load paper A4/Letter-sized. You will need at least four sheets. Printer Parts > Control Panel > Status Print iPF8159 736
2. Press the Menu button to display MAIN MENU.3. Press ▲ or ▼ to select Test Print , and then press the ▶ button. 4. Press ▲ or ▼ to select Status Print, and then press the ▶ button. 5. Press ▲ or ▼ to select Yes, and then press the OK button.Checking the information in the Status Print report The following information is included in the Status Print report.Canon imagePROGRAF iPFxxxx Status Print Printer modelFirm Firmware version Boot Boot ROM version MIT(DBF) MIT database format version MIT(DB) MIT database version S/N Printer serial number MAC Printer MAC address IP Printer IP addressInk Info MCMaintenance Cartridge capacity (%) C, M, Y, MBK, BK Ink levels. The remaining ink is displayed in a five-level scale.Takeup-Reel Status of the Media Take-up UnitMedia Menu Information on the loaded paper. Cut Sheet Type Roll Media Type ManageRemainRoll Job Management Job-related information.HDD Information The free space on the printer's hard disk drive. HDD Space Printer Parts > Control Panel > iPF815 Status Print 9 737
Adjust Printer Current printer settings.Auto Head Adj. Printhead adjustment value. Auto Print Interface Setup Current network settings.EOP Timer Sets the elapsed time between receiving last data and cancel- ing printing. TCP/IP Settings related to TCP/IP. IP Mode Protocol DHCP BOOTP RARP IP Setting IP Setting values. IP Address Subnet Mask Default G/ W NetWare NetWare settings. NetWare Frame Type(*1 →P.738 ) Print Serv- ice(*1 →P.738 ) AppleTalk Values that specify whether AppleTalk is active or not. Ethernet Driver Ethernet Driver settings. Auto Detect Comm.Mode(*2 →P.738 ) Ethernet Type(*2 →P.738 ) Spanning Tree MAC Address *1: Display when NetWare is set to On. *2: Display when Auto Detect is set to On. System Setup System settings.Warning Current warning and error settings. Buzzer Detect MismatchPrinter Parts > Control Panel > Status Print iPF8159 738
Skip Take-Up Err Current warning and error settings. Keep Media Size Current paper-related settings. Paper Size Basis Sheet Selection 1 Sheet Selection 2 TrimEdge Reload Noz. Check Freq. Nozzle-check settings. CarriageScanWdth Carriage scan width setting. Sleep Timer Printer system settings. Length Unit Time Zone Date Format Language Contrast Adj. Output Method Current output method setting. Save and Print Save:Shared Box Information System Info Error Log The past five error codes.GL2 Settings HP-GL/2 setting values. Quality Manager Color Mode Print Quality Input Resolution Print (Economy) Paper Manager Paper Source Margin Conserve Paper Auto Rotate Nesting Use Nesting Nesting Wait- Time Cut Lines ProcessingOption Warning Printer Parts > Control Panel > iPF815 Status Print 9 739
ProcessingOption On-the-Fly HP-GL/2 setting values. PageSizePro- cess1 PageSizePro- cess2 GL2 Settings HP-GL/2 setting values. Line&Pen Manager Enable merge Pen Setup Select Palette Define Palette (Factory) Pen 0 -- Width Pen 1 -- Width Pen 2 -- Width Pen 3 -- Width Pen 4 -- Width Pen 5 -- Width Pen 6 -- Width Pen 7 -- Width Pen 8 -- Width Pen 9 -- Width Pen 10 -- Width Pen 11 -- Width Pen 12 -- Width Pen 13 -- Width Pen 14 -- Width Pen 15 -- Width Define Palette (Palette A) Pen 0 -- Width Pen 1 -- Width Pen 2 -- Width Pen 3 -- Width Pen 4 -- Width Pen 5 -- Width Pen 6 -- Width Pen 7 -- Width Pen 8 -- Width Pen 9 -- WidthPrinter Parts > Control Panel > Status Print iPF8159 740
Pen 10 -- Width HP-GL/2 setting values. Pen 11 -- Width Pen 12 -- Width Pen 13 -- Width Pen 14 -- Width Pen 15 -- Width Define Palette (Palette B) Pen 0 -- Width Pen 1 -- Width Pen 2 -- Width Pen 3 -- Width Pen 4 -- Width Pen 5 -- Width Pen 6 -- Width Pen 7 -- Width Pen 8 -- Width Pen 9 -- Width Pen 10 -- Width Pen 11 -- Width Pen 12 -- Width Pen 13 -- Width Pen 14 -- Width Pen 15 -- Width Smoothing ThickenFineLines AdjustFaintLines Network (RemoteUI) Current network settings used by RemoteUI. TCP/IP Frame Type Use DHCP Use BOOTP Use RARP Enable DNS Dynamic Update Use Zeroconf Function IP Address Subnet Mask Gateway Address Printer Parts > Control Panel > iPF815 Status Print 9 741
LPD Printing Current network settings used by RemoteUI. IPP Printing IPP Printer URI RAW Printing Raw Port Number Raw Mode Bi-direction FTP Printing Primary DNS Server Ad- dress Secondary DNS Server Address DNS Host Name DNS Domain Name Multicast DNS Service Name NetWare NetWare settings. Frame Type IPX External Network Number Node Number Print Service Tree Name Context Name Print Serv- er Name Print Serv- er Pass- word Polling In- terval Current AppleTalk settings. Phase Type Name Network Number Zone HEAD LOT NUMBER Printhead lot number. LOT PARTS STATUS Utilization status of replacement parts that require servic- ing. COUNTER A–Y Printer Parts > Control Panel > Status Print iPF8159 742
COUNTER Utilization status of the cutter, media, and other items (in- dicating how much they have been used). CUTTER MEDIA LIFE TTL LIFE ROLL LIFE CUT- SHEET MEDIA1-7 NAME TTL ROLL CUTSHEET AFTER INSTALLATION Checking Instructions During Printer Operations You can refer to instructions on the printer control panel when loading paper, replacing ink tanks, or performing other oper- ations. How to view instructions Once you complete an action described in the instructions, the printer detects the action and switches to the next instruction screen. In the case of actions the printer cannot detect, instruction screens are switched every four seconds, and the sequence of operations is shown repeatedly. Printer Parts > Control Panel > iPF815 Checking Instructions During Printer Operations 9 743
When all actions in the sequence are finished, the instruction screen for the next step is displayed.Printer Parts > Control Panel > Checking Instructions During Printer Operations iPF8159 744