Canon Imageclass Mf4880dw User Guide

							111
• If toner spills from the toner cartridge, avoid inhaling it or 
allowing it to come into contact with your skin. If the toner 
comes into contact with your skin, wash immediately with soap. 
If you inhale the toner or your skin becomes irritated due to 
contact with the toner, consult a physician or poison control 
center immediately.
Others
 WARNING
• If you are using a cardiac pacemaker: 
This machine generates a low level magnetic fi  eld. If you feel 
any abnormalities in your body while using this machine, please 
move away from the machine and consult your physician 
immediately.
Telephone Equipment
When using telephone equipment, basic safety precautions 
should always be followed to reduce the risk of fi  re, electric shock, 
and injury to persons, including the following:
1.  Do not use this machine near water (i.e., near a bathtub, kitchen  sink, or laundry tub), or in a wet basement or near a swimming 
pool.
2.  Avoid using the telephone during an electrical storm, as there  may be a remote risk of electric shock from lightning. 
3.  Do not use the telephone to report a gas leak in the vicinity of  the leak.
Legal Notices
Legal Limitations on the Usage of Your 
Product and the Use of Images
Using your product to scan, print or otherwise reproduce certain 
documents, and the use of such images as scanned, printed or 
otherwise reproduced by your product, may be prohibited by law 
and may result in criminal and/or civil liability.
A non-exhaustive list of these documents is set forth below. This 
list is intended to be a guide only. If you are uncertain about 
the legality of using your product to scan, print or otherwise 
reproduce any particular document, and/or of the use of the 
images scanned, printed or otherwise reproduced, you should 
consult in advance with your legal advisor for guidance.
• Paper Money
• Money Orders
• Certifi   cates of Deposit
• Postage Stamps (canceled or uncanceled)
• Identifying Badges or Insignias
• Selective Service or Draft Papers
• Checks or Drafts Issued by Governmental Agencies
• Motor Vehicle Licenses and Certifi   cates of Title
• Tr ave l e r s  C h e c k s
• Food Stamps
• Passports
• Immigration Papers
• Internal Revenue Stamps (canceled or uncanceled)
• Bonds or Other Certifi  cates of Indebtedness
• Stock Certifi cates
• Copyrighted Works/Works of Art without Permission of 
Copyright Owner
FCC (Federal Communications Commission)
imageCLASS MF4890dw: F164002
imageCLASS MF4880dw: F164002
imageCLASS MF4770n: F164102
Contains Transmitter Module FCC ID: AZDFM48944
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1.  This device may not cause harmful interference, and
2.  This device must accept any interference received, including 
interference that may cause undesired operation.
FCC WARNING
Changes or modifi   cations not expressly approved by the party 
responsible for compliance could void the user’s authority to 
operate the equipment.
This equipment has been tested and found to comply 
with the limits for a class B digital device, pursuant to 
Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful 
interference in a residential installation. This 
equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful 
interference to radio communications. However, there 
is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause 
harmful interference to radio or television reception, 
which can be determined by turning the equipment 
OFF and ON, the user is encouraged to try to correct 
the interference by one or more of the following 
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and 
receiver.
• Connect the equipment to an outlet on a circuit 
diff  erent from that to which the receiver is 
connected.
• Consult the dealer or an experienced radio/TV 
technician for help.
This transmitter must not be co-located or operated in 
conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure 
limits set forth for an uncontrolled environment 
and meets the FCC radio frequency (RF) Exposure 
Guidelines in Supplement C to OET65. This equipment 
should be installed and operated keeping the radiator 
at least 20cm or more away from person’s body 
(excluding extremities: hands, wrists, feet and ankles).
Use of shielded cables is required to comply with class 
B limits in Subpart B of Part 15 of the FCC Rules. Do not 
make any changes or modifi   cations to the equipment 
unless otherwise specifi   ed in this manual. If you make 
such changes or modifi  cations, you could be required 
to stop operation of the equipment.
Canon U.S.A., Inc.
One Canon Park, Melville, NY 11747, U.S.A.
TEL No. 1-800-OK-CANON
 
						

							112
Users in the U.S.A.
Pre-Installation Requirements for Canon Facsimile Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine. See 
Chapter 1

1, “Appendix,” for specifi   c dimensions and weight.
B. Order Information
1.  A single telephone line (touch-tone or rotary) should be used.
2 . 

Order an RJ11-C telephone wall jack (USOC), which should be 
installed by the telephone company. If the RJ11-C wall jack is 
not present, telephone/facsimile operation is not possible.
3.  Order a normal business line from your telephone company’s  business representative. The line should be a regular voice 
grade line or an equivalent one. Use one line per unit.
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if you communicate 
overseas Canon recommends an individual line following 
industry standards, i.e., 2,500 (touch-tone) or 500 
(rotary/pulse dial) telephones. A dedicated extension 
off   a PBX (Private Branch eXchange) unit without “Call 
Waiting” can be used with your facsimile unit. Key 
telephone systems are not recommended because 
they send nonstandard signals to individual 
telephones for ringing and special codes, which may 
cause a facsimile error.
 C. Power Requirements
The machine should be connected to a standard 120 volt AC, 
thre e

-wire grounded outlet only.
Do not connect this machine to an outlet or power line 
shared with other appliances that cause “electrical noise.” Air 
conditioners, electric typewriters, copiers, and machines of 
this sort generate electrical noise that often interferes with 
communications equipment and the sending and receiving of 
documents.
Connection of the Equipment
This equipment complies with Part 68 of the FCC rules and the 
requirements adopted by the ACTA. On the rear panel of this 
equipment is a label that contains, among other information, 
a product identifi   er in the format of US:AAAEQ##TXXXX. If 
requested, this number must be provided to the telephone 
company.
The REN (Ringer Equivalence Number) is used to determine the 
number of devices that may be connected to a telephone line. 
Excessive RENs on a telephone line may result in the devices not 
ringing in response to an incoming call. In most, but not all areas, 
the sum of the RENs should not exceed fi  ve (5.0). 
To be certain of the number of devices that may be connected to a 
line, as determined by the total RENs, contact the local telephone 
company. The REN for this product is part of the product identifi  er 
that has the format US: AAAEQ##TXXXX. The digits represented by 
## are the REN without a decimal point (e.g., 10 is a REN of 1.0).
An FCC compliant telephone line cable and modular plug is 
provided with this equipment. This equipment is designed to be 
connected to the telephone network or premise wiring using a 
compatible modular jack that is Part 68 compliant. This equipment may not be used on coin service provided by the 
telephone company. Connection to party lines is subjected to 
state tariff
 s.
In Case of Equipment Malfunction
Should any malfunction occur which cannot be corrected by the 
procedures described in this guide or the e-Manual, disconnect 
the equipment from the telephone line cable and disconnect the 
power cord.
The telephone line cable should not be reconnected or the power 
switch turned ON until the problem is completely resolved. Users 
should contact Canon Authorized Service Facilities for servicing 
of equipment, Information regarding Authorized Service Facility 
locations can be obtained by calling Canon Customer Care Center 
(1- 8 0 0 - O K- C AN O N).
Rights of the Telephone Company
If this equipment (imageCLASS MF4890dw/MF4880dw/MF4770n) 
causes harm to the telephone network, the telephone company 
may temporarily disconnect service. The telephone company also 
retains the right to make changes in facilities and services that may 
aff  ect the operation of this equipment. When such changes are 
necessary, the telephone company is required to give adequate 
prior notice to the user.
However, if advance notice is not possible, the telephone 
company will notify the customer as soon as possible. Also, the 
customer will be advised of his/her right to fi   le a complaint with 
the FCC if he/she believes it is necessary.
 WARNING
The Telephone Consumer Protection Act of 1991 makes it 
unlawful for any person to use a computer or other electronic 
device, including FAX machines, to send any message unless such 
message clearly contains in a margin at the top or bottom of each 
transmitted page or on the fi   rst page of the transmission, the date 
and time it is sent and an identifi   cation of the business or other 
entity, or other individual sending the message and the telephone 
number of the sending machine or such business, other entity, or 
individual.
(The telephone number provided may not be a 900 number or 
any other number for which charges exceed local or long-distance 
transmission charges.)
In order to program this information into your 
machine, you should complete the procedure for 
registering your name, unit’s telephone number, time, 
and date in the Starter Guide.
Users in Canada
Pre-Installation Requirements for Canon Facsimile Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine. See 
Chapter 1

1, “Appendix,” for specifi   c dimensions and weight.
B. Order Information
1.  A single telephone line (touch-tone or rotary) should be used.
2 .

  Order a CA11A modular jack, which should be installed by the telephone company. If the CA11A jack is not present, 
installation cannot occur.
3.  Order a normal business line from your telephone company’s  business representative. The line should be a regular voice 
grade line or an equivalent one. Use one line per unit.
 
						

							113
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if you communicate 
overseas Canon recommends an individual line following 
industry standards, i.e., 2,500 (touch-tone) or 500 
(rotary/pulse dial) telephones. A dedicated extension 
off   a PBX (Private Branch eXchange) unit without “Call 
Waiting” can be used with your facsimile unit. Key 
telephone systems are not recommended because 
they send nonstandard signals to individual 
telephones for ringing and special codes, which may 
cause a facsimile error.
C. Power Requirements
The power outlet should be a three-prong grounded receptacle 
( S

ingle or Duplex). It should be independent from copiers, heaters, 
air conditioners, or any electric equipment that is thermostatically 
controlled. The rated value is 115 volts and 15 amperes. The CA11A 
modular jack should be relatively close to the power outlet to 
facilitate installation.
Notice
• This product meets the applicable Industry Canada technical 
specifi  cations.
• The Ringer Equivalence Number is an indication of the 
maximum number of devices allowed to be connected to a 
telephone interface. The termination of an interface may consist 
of any combination of devices subject only to the requirement 
that the sum of the RENs of all the devices does not exceed fi  ve.
• The REN of this product is 1.0.
• Before installing this equipment, users should ensure that 
it is permissible to be connected to the facilities of the local 
telecommunications company. The equipment must also be 
installed using an acceptable method of connection. In some 
cases, the company’s inside wiring associated with a single line 
individual service may be extended by means of a certifi ed 
connector assembly (telephone extension cord). The customer 
should be aware that compliance with the above conditions 
may not prevent deterioration of service in some situations.
• Repairs to certifi   ed equipment should be made by an 
authorized Canadian maintenance facility designated by 
the supplier. Any repairs or alterations made by the user to 
this equipment, or equipment malfunctions, may give the 
telecommunications company cause to request the user to 
disconnect the equipment.
• Users should ensure for their own protection that the electrical 
ground connections of the power utility, telephone lines, and 
internal metallic water pipe system, if present, are connected 
together. This precaution may be particularly important in rural 
areas.
 CAUTION 
Users should not attempt to make such connections themselves, 
but should contact the appropriate electric inspection authority, 
or electrician, as appropriate.
This equipment complies with the Canadian ICES-003 
Class B limits.
Utilisation au Canada
Conditions à Remplir Préalablement à L’installation d’un 
Télécopieur Canon
A. Emplacement
Prévoir une table, un meuble, ou un bureau suffi   sa
 mment solide et 
de taille appropriée (voir le chapitre 11, Annexe (Appendix), pour 
les indications de poids et dimensions).
B. Installation téléphonique
1.  Une seule ligne téléphonique (tonalités ou impulsions) doit être  util i

sée.
2.  Il faut commander un jack modulaire CA11A qui sera installé par  la compagnie téléphonique. Sans ce jack, la mise en place serait 
impossible.
3.  Si vous vous abonnez à une nouvelle ligne, demandez une  ligne d’aff   aires normale de qualité téléphonique courante ou 
équivalente. Prenez un abonnement d’une ligne par appareil.
Ligne automatique interurbaine
ou
Ligne automatique internationale (si vous communiquez avec les 
pays étrangers) Canon vous conseille d’utiliser une ligne individuelle 
conforme aux normes industrielles, à savoir: 
ligne téléphonique 2,500 (pour appareil à clavier) 
ou 500 (pour appareil à cadran/impulsions). Il est 
également possible de raccorder ce télécopieur à 
un système téléphonique à poussoirs car la plupart 
de ces systèmes émettent des signaux d’appel non 
normalisés ou des codes spéciaux qui risquent de 
perturber le fonctionnement du télécopieur.
C. Condition d’alimentation
Raccordez le télécopieur à une prise de courant plus terre à trois 
b r

anches, du type simple ou double, et qui ne sert pas à alimenter 
un copieur, un appareil de chauff   age, un climatiseur ou tout autre 
appareil électrique à thermostat.
L’alimentation doit être de 115 volts et 15 ampères. Pour faciliter 
l’installation, le jack CA11A doit être assez proche de la prise de 
courant.
Remarques
• Le présent matériel est conforme aux spécifi  cations techniques 
applicables d’Industrie Canada.
• Avant d’installer cet appareil, l’utilisateur doit s’assurer qu’il 
est permis de le connecter à l’équipement de la compagnie 
de télécommunication locale et doit installer cet appareil en 
utilisant une méthode de connexion autorisée. Il se peut qu’il 
faille étendre la circuiterie intérieure de la ligne individuelle 
d’abonné, qui a été installée par la compagnie, au moyen d’un 
jeu de connecteurs homologués (rallonge téléphonique).
• L’attention de l’utilisateur est attirée sur le fait que le respect des 
conditions mentionnées ci-dessus ne constitue pas une garantie 
contre les dégradations de qualité du service dans certaines 
circonstances.
• L’indice d’équivalence de la sonnerie (IES) sert à indiquer le 
nombre maximal de terminaux qui peuvent être raccordés à 
une interface téléphonique. La terminaison d’une interface 
peut consister en une combinaison quelconque de dispositifs, 
à la seule condition que la somme d’indices d’équivalence de la 
sonnerie de tous les dispositifs n’excède pas 5.
 
						

							114
• Le nombre d’équivalents sonnerie (REN) de ce produit est 1,0.
• Les réparations sur un appareil certifi  é doivent être faites 
par une société d’entretien canadienne autorisée par le 
Gouvernement canadien et désignée par le fournisseur. Toute 
réparation ou modifi   cation que pourrait faire I’utilisateur de 
cet appareil, ou tout mauvais fonctionnement, donne à la 
compagnie de télécommunication le droit de débrancher 
I’appareil.
• Pour sa propre protection, I’utilisateur doit s’assurer que 
les prises de terre de I’appareil d’alimentation, les lignes 
téléphoniques et les tuyaux métalliques internes, s’il y en a, sont 
bien connectés entre eux. Cette précaution est particulièrement 
importante dans les zones rurales
 CAUTION 
Au lieu d’essayer de faire ces branchements eux-mêmes, les 
utilisateurs sont invités à faire appel à un service d’inspection 
faisant autorité en matière d’électricité ou à un électricien, selon 
le cas.
Respecte les limites de la classe B de la NMB-003 du 
Canada.
Laser Safety
This machine complies with 21 CFR Chapter 1 Subchapter J as 
a Class 1 laser product under the U.S. Department of Health 
and Human Services (DHHS) Radiation Performance Standard 
according to the Radiation Control for Health and Safety Act of 
1968. This means that the machine does not produce hazardous 
radiation.
Since radiation emitted inside the machine is completely confi  ned 
within protective housings and external covers, the laser beam 
cannot escape from the machine during any phase of user 
operation.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the 
U.S. Food and Drug Administration implemented regulations 
for laser products on August 2, 1976. These regulations apply to 
laser products manufactured from August 1, 1976. Compliance is 
mandatory for products marketed in the United States.
 CAUTION 
Use of controls, adjustments, or performance of procedures 
other than those specifi   ed in this manual may result in hazardous 
radiation exposure.
The label is attached to the laser scanner machine inside the
machine and is not in a user access area.
 
						

							115115
 Memo 
  
 
						

							FT6-0296 (010) XXXXXXXXXX © CANON INC.  2013  PRINTED IN KOREA
CANON INC.30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON MARKETING JAPAN INC.16-6, Konan 2-chome, Minato-ku, Tokyo 108-8011, Japan
CANON U.S.A., INC.One Canon Park, Melville, NY 11747, U.S.A.
CANON EUROPA N.V.Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands
CANON CHINA CO. LTD.15F Jinbao Building No.89, Jinbao Street, Dongcheng District, Beijing 10\
0005, PRC
CANON SINGAPORE PTE LTD1 HarbourFront Avenue, #04-01 Keppel Bay Tower, Singapore 098632
CANON AUSTRALIA PTY LTD1 Thomas Holt Drive, North Ryde, Sydney NSW 2113, Australia
CANON GLOBAL WORLDWIDE SITEShttp://www.canon.com/
Serial No. 
Date of Purchase