Brother MFC 9440CN User Manual

Making copies
71
12
Copy options 
(temporary settings)
12
When you want to quickly change the copy 
settings temporarily for the next copy, use the 
temporary Copy keys. You can use different 
combinations.
 
The machine returns to its default settings 
after 60 seconds or if the Mode Timer returns 
the machine to Fax mode. (See Mode timer 
on page 20.)
Enlarging or reducing the 
image copied12
You can choose the following enlargement or 
reduction ratios:
Custom(25-400%) allows you to enter a 
ratio...

Chapter 12
72
Using the Options key12
Use the Options key to quickly set the following copy settings temporarily for the next copy.
Press
 
Menu selections Options Page
Press a or b, then Press OK
 
Press a or b, then Press OK
 
QualityAuto*
Text
Photo73
Stack/Sort
(appears when the document 
is in the ADF)Stack*
Sort73
Brightnessb
 -nnonn+ a*
b -nnnon+ a
b
 -nnnno+ a
b
 -onnnn+ a
b
 -nonnn+ a
74
Contrastb
 -nnonn+ a*
b -nnnon+ a
b
 -nnnno+ a
b
 -onnnn+ a
b
 -nonnn+ a
74
Page LayoutOff(1 in 1)*
2in1(P)...

Making copies
73
12
Changing copy quality12
You can choose from a range of quality 
settings. The default setting is Auto.
„Auto
Auto is the recommended mode for 
ordinary printouts. Suitable for documents 
that contain both text and photographs.
„Text
Suitable for documents containing only 
text.
„Photo
Suitable for copying photographs.
To temporarily change the quality setting, 
follow the steps below:
aMake sure you are in Copy mode  .
bLoad your document.
cUse the dial pad to enter the number of...

Chapter 12
74
Adjusting brightness, 
contrast and colour12
Brightness12
Adjust the copy brightness to make copies 
darker or lighter.
To temporarily change the copy brightness 
setting, follow the steps below:
aMake sure you are in Copy mode  .
bLoad your document.
cUse the dial pad to enter the number of 
copies (up to 99).
dPress Options.
Press a or b to choose Brightness.
PressOK.
ePress a to make a lighter copy or press 
b to make a darker copy. 
PressOK.
fPress Mono Start or Colour Start.
To change...

Making copies
75
12
Colour Adjust12
You can change the default setting for colour 
saturation.
To change the default setting follow the steps 
below:
aPress Menu, 3, 4. 
Copy
4.Color Adjust
bPress a or b to choose 1.Red, 2.Green 
or 3.Blue.
PressOK.
cPress a or b to increase or decrease the 
colour saturation.
PressOK.
dReturn to b to choose the next colour. 
Or press Stop/Exit.
Making N in 1 copies 
(page layout)12
You can reduce the amount of paper used 
when copying by using the N in 1 copy 
feature....

Chapter 12
76
If you are copying from the ADF:12
Insert your document face up in the direction 
shown below:
„2 in 1 (P)
 
„2 in 1 (L)
 
„4 in 1 (P)
 
„4 in 1 (L)
 
If you are copying from the scanner 
glass:
12
Insert your document face down in the 
direction shown below:
„2 in 1 (P)
 
„2 in 1 (L)
 
„4 in 1 (P)
 
„4 in 1 (L)
 
Tray selection12
You can change the tray use only for the next 
copy.
aMake sure you are in Copy mode  .
bLoad your document.
cUse the dial pad to enter the number of 
copies (up...

Making copies
77
12
Out of memory 
message
12
If the memory becomes full while you are 
making copies, the LCD message will guide 
you through the next step.
If you get an Out of Memory message 
while scanning a subsequent page, you will 
have the option to press Mono Start or 
Colour Start to copy the pages scanned so 
far, or to press Stop/Exit to cancel the 
operation.
To make extra memory available, you can do 
the following:
„Print the faxes that are in the memory. 
(See Printing a fax from the...

Chapter 12
78
 

Section IV
Direct printingIV
Printing photos from a digital camera80
Printing data from a USB flash memory drive84
 

80
13
 
Your Brother machine supports the 
PictBridge standard, allowing you to connect 
to and print photos directly from any 
PictBridge compatible digital camera.
Even if your camera is not in PictBridge mode 
or does not support PictBridge, you can still 
print photos from a digital camera in mass 
storage mode. (See Connecting a camera as 
a storage device on page 82.)
Before using 
PictBridge
13
PictBridge requirements13
To avoid errors, remember the following 
points:
„The machine and the digital...