Brother MFC 9320CW User Manual

Section III
CopyIII
Making copies80
 

80
12
How to copy12
Entering copy mode12
Press  (Copy) to enter Copy mode.
 
1 Stack/Sort
2 Copy ratio and Copy layout
3 Contrast
4 Quality
5 Number of copies
Making a single copy12
aMake sure you are in Copy mode  .
bLoad your document in the ADF or on 
the scanner glass.
cPress  Mono Start  or Colour Start .
Making multiple copies12
aMake sure you are in Copy mode  .
bLoad your document.
cUse the dial pad to enter the number of 
copies (up to 99).
dPress Mono Start  or Colour Start .
Note
• To sort...

Making copies81
12
Copy options 
(temporary settings)
12
When you want to quickly change the copy 
settings temporarily for the next copy, use the 
temporary Copy keys. You can use different 
combinations.
 
The machine returns to its default settings 
one minute after copying, unless you have 
set the Mode Timer to 30 seconds or less. 
(See  Mode Timer  on page 24.)
Enlarging or reducing the 
image copied12
You can choose the following enlargement or 
reduction ratios:
* The factory setting is shown in...

Chapter 12
82
Using the Options key12
Use the  Options  key to quickly set the following copy settings temporarily for the next copy.
Press
 
Menu selections Options Page
Press a or  b, then press  OK
 
Press a or  b, then press  OK
 
Stack/Sort
(appears when the document 
is in the ADF) Stack
*
Sort 83
Brightness b- onnnn +a
b - nonnn +a
b - nnonn +a*
b - nnnon +a
b - nnnno +a 84
Contrast b- onnnn +a
b - nonnn +a
b - nnonn +a*
b - nnnon +a
b - nnnno +a 83
Page Layout Off(1 in 1)*
2 in 1 (P)
2 in 1 (L)...

Making copies83
12
Improving copy quality12
You can choose from a range of quality 
settings. The default setting is  Auto.
„ Auto
Auto is the recommended mode for 
ordinary printouts. Suitable for documents 
that contain both text and photographs.
„ Photo
Suitable for copying photographs.
„ Text
Suitable for documents containing only 
text.
To  temporarily  change the quality setting, 
follow the steps below:
aMake sure you are in Copy mode  .
bLoad your document.
cUse the dial pad to enter the number...

Chapter 12
84
To change the  default setting follow the steps 
below:
aPress  Menu, 3, 3.
bPress  a or  b to increase or decrease the 
contrast.
Press  OK.
cPress  Stop/Exit .
Brightness12
Adjust the copy brightness to make copies 
darker or lighter.
To temporarily  change the copy brightness 
setting, follow the steps below:
aMake sure you are in Copy mode  .
bLoad your document.
cUse the dial pad to enter the number of 
copies (up to 99).
dPress  Options .
Press  a or  b to choose  Brightness .
Press...

Making copies85
12
ePress a or  b to choose  2in1(P) , 
2in1(L) , 4in1(P) , 
4in1(L)  or Off(1 in 1) .
Press  OK.
fPress  Mono Start  or Colour Start  to 
scan the page.
If you placed the document in the ADF, 
the machine scans the pages and starts 
printing.
If you are using the scanner glass, go 
to step g.
gAfter the machine scans the page, 
press 1 to scan the next page.
 
Next Page?
1.Yes 2.No
hPut the next page on the scanner glass.
Press  OK.
Repeat steps g and  h for each page of 
the layout....

Chapter 12
86
Out of memory 
message
12
If the memory becomes full while you are 
making copies, the LCD message will guide 
you through the next step.
If you get an  Out of Memory  message 
while scanning a subsequent page, you will 
have the option to press  Mono Start or 
Colour Start  to copy the pages scanned so 
far, or to press  Stop/Exit to cancel the 
operation.
To gain extra memory, you can do the 
following:
„ Print the faxes that are in the memory. 
(See  Printing a fax from the memory  
on...

Section IV
Direct printingIV
Printing photos from a digital camera 
(MFC-9320CW only)
88
Printing data from a USB Flash memory drive 
(MFC-9320CW only)
93
 

88
13
 
Your Brother machine supports the 
PictBridge standard, allowing you to connect 
to and print photos directly from any 
PictBridge compatible digital camera.
Even if your camera is not in PictBridge mode 
or does not support PictBridge, you can 
connect your camera as a normal storage 
device. This enables you to print photos from 
your camera. Follow the steps for “Printing 
data from a USB Flash memory drive 
(MFC-9320CW only)  on page 93”.
Before using 
PictBridge
13
PictBridge...