Brother MFC 9120CN User Manual

Making copies89
12
Improving copy quality12
You can choose from a range of quality 
settings. The default setting is  Auto.
„ Auto
Auto is the recommended mode for 
ordinary printouts. Suitable for documents 
that contain both text and photographs.
„ Photo
Suitable for copying photographs.
„ Text
Suitable for documents containing only 
text.
To  temporarily  change the quality setting, 
follow the steps below:
aMake sure you are in Copy mode  .
bLoad your document.
cUse the dial pad to enter the number...

Chapter 12
90
To change the  default setting follow the steps 
below:
aPress  Menu, 3, 3.
bPress  a or  b to increase or decrease the 
contrast.
Press  OK.
cPress  Stop/Exit .
Brightness12
Adjust the copy brightness to make copies 
darker or lighter.
To temporarily  change the copy brightness 
setting, follow the steps below:
aMake sure you are in Copy mode  .
bLoad your document.
cUse the dial pad to enter the number of 
copies (up to 99).
dPress  Options .
Press  a or  b to choose  Brightness .
Press...

Making copies91
12
ePress a or  b to choose  2in1(P) , 
2in1(L) , 4in1(P) , 
4in1(L)  or Off(1 in 1) .
Press  OK.
fPress  Mono Start  or Colour Start  to 
scan the page.
If you placed the document in the ADF, 
the machine scans the pages and starts 
printing.
If you are using the scanner glass, go 
to step g.
gAfter the machine scans the page, 
press 1 to scan the next page.
 
Next Page?
1.Yes 2.No
hPut the next page on the scanner glass.
Press  OK.
Repeat steps g and  h for each page of 
the layout....

Chapter 12
92
Out of memory 
message
12
If the memory becomes full while you are 
making copies, the LCD message will guide 
you through the next step.
If you get an  Out of Memory  message 
while scanning a subsequent page, you will 
have the option to press  Mono Start or 
Colour Start  to copy the pages scanned so 
far, or to press  Stop/Exit to cancel the 
operation.
To gain extra memory, you can do the 
following:
„ Print the faxes that are in the memory. 
(See  Printing a fax from the memory  
on...

Section IV
Direct printingIV
Printing photos from a digital camera 
(MFC-9320CW only)
94
Printing data from a USB Flash memory drive 
(MFC-9320CW only)
99
 

94
13
 
Your Brother machine supports the 
PictBridge standard, allowing you to connect 
to and print photos directly from any 
PictBridge compatible digital camera.
Even if your camera is not in PictBridge mode 
or does not support PictBridge, you can 
connect your camera as a normal storage 
device. This enables you to print photos from 
your camera. Follow the steps for “Printing 
data from a USB Flash memory drive 
(MFC-9320CW only)  on page 99”.
Before using 
PictBridge
13
PictBridge...

Printing photos from a digital camera (MFC-9320CW only)95
13
aPress Menu, 5, 3. 
USB Direct I/F
3.PictBridge
bTo set the PictBridge settings, press  a or 
b  to choose  1.Paper Size , 
2.Orientation , 3.Date & Time , 
4.File Name , or 5.Print Quality .
Press OK.
cPress  a or  b to choose an option for 
each menu setting.
Press OK.
Repeat  b to  c for each PictBridge 
setting.
dPress  Stop/Exit .
Note
• Camera settings are prioritized as long as 
your camera is not set to use your 
machine’s settings...

Chapter 13
96
IMPORTANT
• To prevent damage to your machine, do  not connect any device other than a digital 
camera or USB flash memory drive to the 
USB direct interface.
• DO NOT remove the digital camera from  the USB direct interface until the machine 
has finished printing.
 
DPOF printing13
DPOF stands for Digital Print Order Format.
Major digital camera manufacturers (Canon 
Inc., Eastman Kodak Company, FUJIFILM 
Corporation, Panasonic Corporation and 
Sony Corporation) created this standard to...

Printing photos from a digital camera (MFC-9320CW only)97
13
dEnter the password. Press OK. 
Change ID
PIN:XXXX
Note
If your ID has restricted options, the 
following messages appear on the LCD.
 
eThe LCD shows the following message 
depending on which mode the machine 
is in:
 
04/20 15:30 Fax
Camera Connected
 
Scan:Select ab
Camera Connected
 
Stack Copies:01
Camera Connected
fSet your camera to print an image. Set 
the number of copies if you are asked.
When the machine starts printing an 
image,...

Chapter 13
98
Connecting a camera 
as a storage device
13
Even if your camera is not in PictBridge 
mode, or does not support PictBridge, you 
can connect your camera as a normal 
storage device. This enables you to print 
photos from your camera.
Follow the steps in  Printing data directly from 
the USB Flash memory drive (MFC-9320CW 
only)  on page 100.
(If you would like to print photos in PictBridge 
mode, see  Setting your digital camera  
on page 94.)
Note
The name of the storage mode and...