Brother Mfc 6490cw User Manual

							
Troubleshooting and Routine Maintenance169
B
CAUTION 
DO NOT take out ink cartridges if you do 
not need to replace them. If you do so, it 
may reduce the ink quantity and the 
machine will not know the quantity of ink left 
in the cartridge.
 
 
DO NOT touch the cartridge insertion slots. 
If you do so, the ink may stain your skin.
  
If ink gets on your skin or clothing 
immediately wash it off with soap or 
detergent.
  
If you mix the colours by installing an ink 
cartridge in the wrong position, clean the 
print head several times after correcting the 
cartridge installation.
  
Once you open an ink cartridge, install it in 
the machine and use it up within six months 
of installation. Use unopened ink cartridges 
by the expiration date written on the 
cartridge package.
  
DO NOT dismantle or tamper with the ink 
cartridge, this can cause the ink to leak out 
of the cartridge.
 
Cleaning the outside of the 
machineB
CAUTION 
Use neutral detergents. Cleaning with 
volatile liquids such as thinner or benzine 
will damage the outside surface of the 
machine.
  
DO NOT use cleaning materials that 
contain ammonia.
 
 
DO NOT use isopropyl alcohol to remove 
dirt from the control panel. It may crack the 
panel.
 
Clean the outside of the machine as 
follows:
B
aPull the paper trays (1) completely out of 
the machine.
 
 
1
1
 
						

							
170
bWipe the outside of the machine with a 
soft cloth to remove dust.
 
cRemove anything that is stuck inside the 
paper tray.
dWipe the paper trays with a soft cloth to 
remove dust.
 
ePut the paper trays firmly back in the 
machine.
Cleaning the scanner glassB
aLift the document cover (1). Clean the 
scanner glass (2) and the white 
plastic (3) with a soft lint-free cloth 
moistened with a non-flammable glass 
cleaner.
 
bIn the ADF unit, clean the white bar (1) 
and the glass strip (2) with a lint-free 
cloth moistened with a non-flammable 
glass cleaner.
 
Note
In addition to cleaning the glass strip with 
a non-flammable glass cleaner, run your 
finger tip over the glass strip to see if you 
can feel anything on it. If you feel dirt or 
debris, clean the glass strip again 
concentrating on that area. You may need 
to repeat the cleaning process three or 
four times. To test, make a copy after each 
cleaning attempt.
 
1
3
2
1
2
 
						

							
Troubleshooting and Routine Maintenance171
B
Cleaning the machine printer 
platenB
WARNING 
Be sure to unplug the machine from the 
electrical socket before cleaning the printer 
platen.
 
aUsing both hands, use the finger holds 
on both sides of the machine to lift the 
scanner cover until it locks securely into 
the open position.
bClean the machine’s printer platen (1) 
and the area around it, wiping off any 
scattered ink with a soft, dry, lint-free 
cloth.
 
Cleaning the paper pick-up 
rollerB
aPull the paper trays completely out of 
the machine.
b(MFC-5890CN) 
Unplug the machine from the electrical 
socket and open the Jam Clear 
Cover (1) at the back of the machine.
 
(MFC-6490CW) 
Unplug the machine from the electrical 
socket and open the Outer Rear 
Cover (1) and Inner Rear Cover (2) from 
the back of the machine.
 
1
1
1
2
 
						

							
172
cClean the Paper Pick-up Roller (1) with 
isopropyl alcohol on a cotton swab.
 
d(MFC-5890CN) 
Close the Jam Clear Cover properly. 
(MFC-6490CW) 
Close the Inner Rear Cover and the 
Outer Rear Cover.
Make sure the cover is closed correctly.
ePut the paper trays firmly back in the 
machine.
fRe-connect the power cord.
Cleaning the print headB
To maintain print quality, the machine will 
automatically clean the print head. You can 
start the cleaning process manually if there is 
a print quality problem.
Clean the print head and ink cartridges if you 
get a horizontal line or blank text in the text or 
graphics on your printed pages. You can 
clean Black only, three colours at a time 
(Cyan/Yellow/Magenta), or all four colours at 
once.
Cleaning the print head consumes ink. 
Cleaning too often uses ink unnecessarily.
CAUTION 
DO NOT touch the print head. Touching the 
print head may cause permanent damage 
and may void the print heads warranty.
 
aPress Ink Management .
bPress aor b to choose  Cleaning.
Press  OK.
cPress  aor b to choose  Black, Color  or 
All .
Press  OK.
The machine cleans the print head. 
When cleaning is finished, the machine 
will go back to standby mode 
automatically.
Note
If you clean the print head at least five 
times and the print has not improved, try 
installing a new genuine Brother Branded 
replacement cartridge for each problem 
colour. Try cleaning the print head again 
up to five more times. If the print has not 
improved call your Brother dealer.
 
Checking the print qualityB
If faded or streaked colours and text appear 
on your output, some of the nozzles may be 
clogged. You can check this by printing the 
Print Quality Check Sheet and looking at the 
nozzle check pattern.
aPress  Ink Management .
bPress aor b to choose  Test Print .
Press  OK.
cPress  aor b to choose 
Print Quality .
Press  OK.
dPress  Colour Start .
The machine begins printing the Print 
Quality Check Sheet.
eCheck the quality of the four colour 
blocks on the sheet.
1
 
						

							
Troubleshooting and Routine Maintenance173
B
fThe LCD asks you if the print quality is 
OK.
Do one of the following:„ If all lines are clear and visible, press 
1 ( Yes ) to finish the Print Quality 
check and go to step j.
„ If you can see missing short lines as 
shown below, press  2 to choose  No.
gThe LCD asks you if the print quality is 
OK for black and three colours.
Press  1 ( Yes ) or 2 ( No ).
hThe LCD asks you if you want to start 
cleaning.
Press  1 ( Yes ).
The machine starts cleaning the print 
head.
iAfter cleaning is finished, press 
Colour Start .
The machine starts printing the Print 
Quality Check Sheet again and then 
return to step e. 
jPress  Stop/Exit .
If you repeat this procedure at least five 
times and the print quality is still poor, 
replace the ink cartridge for the clogged 
colour. 
After replacing the ink cartridge, check 
the print quality. If the problem still 
exists, repeat the cleaning and test print 
procedures at least five times for the 
new ink cartridge. If ink is still missing, 
call your Brother dealer.
CAUTION 
DO NOT touch the print head. Touching the 
print head may cause permanent damage 
and may void the print heads warranty.
 
Note
 

OK Poor
   

OK Poor
  
 
i
 
When a print head 
nozzle is clogged 
the printed 
sample looks like 
this.After the print 
head nozzle is 
cleaned, the 
horizontal lines 
are gone.
 
						

							
174
Checking the print alignmentB
You may need to adjust the print alignment 
after transporting the machine, if your printed 
text becomes blurred or images become 
faded.
aPress Ink Management .
bPress aor b to choose  Test Print .
Press  OK.
cPress  aor b to choose  Alignment .
Press  OK.
dPress  Mono Start  or Colour Start .
The machine starts printing the 
Alignment Check Sheet.
eCheck the 600 dpi and 1200 dpi test 
prints to see if number 5 most closely 
matches number 0. 
fDo one of the following:
„ If the number 5 samples of both the 
600 dpi and 1200 dpi test prints are 
the best matches, press  1 ( Yes ) to 
finish the Alignment Check and go to 
step i.
„ If another test print number is a 
better match for either 600 dpi or 
1200 dpi, press  2 ( No ) to choose it.
gFor 600 dpi, press the number of the test 
print that most closely matches the 
number 0 sample (1-8).
hFor 1200 dpi, press the number of the 
test print that most closely matches the 
number 0 sample (1-8).
iPress  Stop/Exit .
Checking the ink volumeB
Although an ink volume icon appears on the 
LCD, you can use the  Ink Management key 
to see a large graph showing the ink that is 
left in each cartridge.
aPress  Ink Management .
bPress aor b to choose  Ink Volume .
Press  OK.
The LCD shows the ink volume.
cPress  Stop/Exit .
Note
You can check the ink volume from your 
computer. (See  Printing for Windows
® or 
Printing and Faxing  for Macintosh
® in the 
Software User’s Guide on the CD-ROM.)
 
 
						

							
Troubleshooting and Routine Maintenance175
B
Machine InformationB
Checking the serial numberB
You can see the machine’s serial number on 
the LCD.
aPress Menu.
bPress  aor b to choose  Machine Info .
Press  OK.
cPress  aor b to choose  Serial No .
Press  OK.
dPress  Stop/Exit .
Packing and shipping 
the machine
B
When you transport the machine, use the 
packing materials that came with your 
machine. Follow the instructions below to 
properly pack your machine. Damage caused 
to your machine during transit is not covered 
by your warranty.
CAUTION 
It is important to allow the machine to ‘park’ 
the print head after a print job. Listen 
carefully to the machine before unplugging 
it to make sure that all mechanical noise 
has stopped. Not allowing the machine to 
finish this parking process may lead to print 
problems and possible damage to the print 
head.
 
aOpen the ink cartridge cover.
bPress the lock release lever to release 
the ink cartridge and take out all the ink 
cartridges. (See  Replacing the ink 
cartridges  on page 166.)
cInstall the green protective part and then 
close the ink cartridge cover.
 
 
						

							
176
CAUTION 
Make sure that the plastic tabs on both 
sides of the green protective part (1) have 
securely clicked into place (2).
  If you are not able to find the green 
protective part, DO NOT remove the ink 
cartridges before shipping. It is essential 
that the machine be shipped with either the 
green protective part or the ink cartridges in 
position. Shipping without them will cause 
damage to your machine and may void your 
warranty. When travelling with the ink 
cartridges still in the machine please keep 
the machine upright as this will protect the 
machine from leakage.
 
dUnplug the machine from the telephone 
wall socket and take the telephone line 
cord out of the machine.
eUnplug the machine from the electrical 
socket and from the machine.
f(MFC-5890CN) 
Using both hands, use the finger holds 
on both sides of the machine to lift the 
scanner cover until it locks securely into 
the open position. Then unplug the 
interface cable from the machine, if it is 
connected. 
(MFC-6490CW) 
Using both hands, use the finger holds 
on both sides of the machine to lift the 
scanner cover into the open position. 
Then unplug the interface cable from the 
machine, if it is connected.
g(MFC-5890CN) 
Lift the scanner cover (1) to release the 
lock. Gently push the scanner cover 
support down (2) and close the scanner 
cover (3).
 
(MFC-6490CW) 
Gently close the scanner cover using 
the finger holds on both sides of it as you 
push down on the Scanner Cover 
Support (1).
 
WARNING 
Be careful not to trap your fingers under the 
scanner cover. 
Always use the finger holds provided on 
both sides of the scanner cover when 
opening and closing it. 
 
 
 
1
2
1
 
						

							
Troubleshooting and Routine Maintenance177
B
hWrap the machine in the bag. 
iPack the machine and the printed 
materials in the original carton with the 
original packing material as shown 
below. Do not pack the used ink 
cartridges in the carton.
(MFC-5890CN)
 
(MFC-6490CW) 
jClose the carton and tape it shut. 
 
						

							
178
C
On-screen 
programming
C
Your machine is designed to be easy to 
operate with LCD on-screen programming 
using the menu keys. User-friendly 
programming helps you take full advantage of 
all the menu selections your machine has to 
offer.
Since your programming is done on the LCD, 
we have created step-by-step on-screen 
instructions to help you program your 
machine. All you need to do is follow the 
instructions as they guide you through the 
menu selections and programming options.
Menu tableC
You can program your machine by using the 
Menu table that begins on page 179. These 
pages list the menu selections and options.
Memory storageC
Even if there is a power failure, you will not 
lose the settings you have chosen using the 
Menu key because they are stored 
permanently. Also, you will not lose your 
settings in the PhotoCapture, Fax and Copy 
mode key menus if you have chosen 
Set New Default. You may have to reset 
the date and time.
Note
During a power failure the machine will 
retain messages that are in the memory 
for approximately 24 hours.
 
Mode and menu keysC
Menu and FeaturesC
 
Access the main menu.
 
Press to access the temporary 
settings for each mode.
a
b Scroll through the current menu 
level.
d Go back to the previous menu 
level.
c Go to the next menu level.
 „Go to the next menu level.
„ Accept an option.
 „Cancel the current operation.
„ Go back to the previous menu 
level.
 
„Stop the current operation.