Brother Hl 4200cn User Manual

CONTROL PANEL   4 - 8
Text Print
Setting Text Print to Yes, will ensure all data will be printed as it is received and any control codes 
embedded within the document will be ignored. For most printing environments, we recommend that you 
set this option to Yes.
■Yes (default) 
The data is printed as text.
■No
Data is not printed as text.
Auto Continue
When there is no paper in the tray that you specified from the driver, load the nearest paper size from 
another tray. 
■No 
The printer does not print...

4 - 9   CONTROL PANEL
Maintenance Mode
Use this mode to reset the non-volatile (NV) memory or to adjust paper quality settings. You can use this 
mode to restrict access to certain menus.
Init NVM
Resets the printers NV memory. This resets all of the printer’s settings back to its factory settings, or 
default settings. 
The NV memory stores the printer’s configuration data, even when the printer is switched off.
You cannot change this setting while the printer is processing print data.
■YES 
Resets the...

CONTROL PANEL   4 - 10
BTR CurrentAdj
When duplex printing on non-recommended paper, the print quality may be poor. To improve the quality, 
change this setting according to the type of media that is being used. 
■Plain Paper
■Plain Paper BK (BackFace)
■Plain Paper (HighGloss)
■Plain Paper (HighGloss and BackFace)
■Thick Paper 1
■Thick Paper 1 (BackFace)
■Thick Paper 2
■Thick Paper 2 (BackFace)
■Glossy Paper
■Glossy Paper (BackFace)
Media Current Adj. default setting is 0.
Media Current Adj. setting may...

4 - 11   CONTROL PANEL
Parallel
Use Parallel to configure the parallel interface.
ECP
Use ECP to configure the ECP communication mode of the parallel interface.
■Enabled (default) 
The printer receives data in ECP mode.
■Disabled 
The printer does not receive data in ECP mode.
Adobe Protocol
To set the Adobe Protocol choose one of the following:
■Auto
■Standard
■BCP
■TBCP (default)
 

CONTROL PANEL   4 - 12
Report/List
Use Report/List to print reports and lists.
Reports and lists are printed on A4 or Letter paper. (The requested paper size depends on your 
country.) Put A4 or Letter paper lengthwise into the paper tray.
Printer Settings
Printer Settings is a list of the installed hardware and the configuration details. 
For an example of the printer configuration list, consulte Confirming Printer Configuration and Network 
Settings en la página 7-19.
Panel Settings
Panel Settings is a...

4 - 13   CONTROL PANEL
Network
Use Network to make or change network settings. 
■You cannot change the Network setting while the printer is processing print data.
■You must restart the printer for settings to take effect. After programming settings, be sure to 
restart the printer.
Ethernet
Use Ethernet to set Ethernet communication speed and mode.
■Auto (default) 
10Base-T Half, 10Base-T Full, 100Base-TX Half, or 100Base-TX Full is selected automatically. 
■10Base/Half
■10Base/Full
■100Base/Half...

CONTROL PANEL   4 - 14
■Subnet Mask 
Use this to set the subnet mask address. 
[aaa.bbb.ccc.ddd] 
Use 0,128, 192, 224, 240, 248, 252, 254, or 255 for aaa, bbb, ccc, and ddd.
■Gateway Address 
Use this to set the gateway address. 
[aaa.bbb.ccc.ddd] 
Set aaa, bbb, ccc, and ddd between 0 and 255. 
You cannot use the following:
IPX Frame Type
Set a frame type when you use the printer in an IPX/SPX (NetWare) environment.
■Auto (default) 
Sets the frame type automatically.
■802.3 
Set this to use IEEE 802.3...

4 - 15   CONTROL PANEL
■NetWare (default: Enabled) 
Set NetWare to Enabled to print in a NetWare system or to Disabled if you do not want to use 
this feature.
■AppleTalk (default: Enabled) 
Set AppleTalk to Enabled to print in an AppleTalk system or to Disabled if you do not want to 
use this feature.
IP Filter
Use IP Filter to block the reception of data from certain locations.
To block a particular IP address, specify the IP address in FilterX Address (X is a number between 1 
and 5) and the subnet...

CONTROL PANEL   4 - 16
USB
Adobe PS Protocol
To set the Adobe Protocol choose one of the following:
■TBCP (default)
■RAW
■Standard
■BCP
 

5 - 1   TROUBLESHOOTING
5
Read this chapter to learn how to correct printer problems.
If it looks like you are unable to fix the problem
Turn the printer off, disconnect the power cord from the AC outlet/socket, and contact your dealer or 
Brother Customer Service for assistance.
Do not make any changes or modifications to the equipment, as this may cause a fire or an electric 
shock. 
Turn the printer off and disconnect the power cord from the AC outlet/socket before performing 
maintenance on the...