Brother Hl 3260n User Manual

4-38
☛
☛☛ ☛ 4.Push down the paper guide lever.
ZAEY250E 
Fig. 4-62
✒
✒✒ ✒  Note
If the paper guide lever is not pushed down, paper misfeeds may occur.
☛
☛☛ ☛ 5.Turn on the printer.
☛
☛☛ ☛ 6.Configure the paper feed unit direction and the paper size.
✒
✒✒ ✒ Note
The paper size specified with the printer driver overrides the one specified
here.
 

CHAPTER 4 OPTIONS
4-39
M M
a a
i i
l l
b b
o o
x x
   
u u
n n
i i
t t
   
( (
M M
X X
- -
5 5
0 0
0 0
0 0
) )
With this option, printed pages can be sent to four output trays. After
installing the Interchange unit, install the Mailbox on the top of the
Interchange unit.
The Mailbox unit is an optional device that is installed onto the this laser
printer that allows you to direct your printouts to any bin that you have
specified.
I I
n n
s s
t t
a a
l l
l l
i i
n n
g g
   
t t
h h
e e
   
M M
a a
i i
l...

4-40
☛
☛☛ ☛ 2.Turn off the printer, and remove all cables and the power cord from the
printer.
☛
☛☛ ☛ 3.Remove the adhesive tape.
ZAEP440E 
Fig. 4-64
☛
☛☛ ☛ 4.If you installed the Duplex unit, open the Duplex unit by lifting the catch.
ZAEP330E 
Fig. 4-65
☛
☛☛ ☛ 5.Open the right cover by lifting the catch.
ZAEP271E 
Fig. 4-66
 

CHAPTER 4 OPTIONS
4-41
☛
☛☛ ☛ 6.If the cover of the Interchange unit is attached, remove it by lifting the cover
at the rear of the printer first as shown below.
ZAEP710E 
1
2
Fig. 4-67
✒ Note
• If the cover of the Interchange unit is already removed, go to Step 7.
• The removed cover is no longer required.
☛
☛☛ ☛ 7.Hold the Mailbox on both sides and fit it onto the top of the Interchange unit.
ZAEP340E 
Fig. 4-68
 

4-42
☛
☛☛ ☛ 8.Fasten the two screws hand tight and secure the Mailbox to the printer. Use
a coin to tighten the screws securely.
ZAEP350E 
Fig. 4-69
☛
☛☛ ☛ 9.Close the Right cover by pushing the area as shown in the illustration.
ZAEP690E 
Fig. 4-70
☛
☛☛ ☛ 10.If the Duplex unit is already attached, close the unit.
☛
☛☛ ☛ 11.Slide the four mailbox output trays into the Mailbox unit starting from the
bottom tray.
ZAEP360E 
Fig. 4-71
 

CHAPTER 4 OPTIONS
4-43

	











	
	
				
			



			 !	 	#!		$##%!	#!#!&


(	#	(	)*		#	+	 ,&
♦ 
	

-	##!	#%	.#	#		.#	!#	#	!.	 !		.#	$.,
♦ 
	

/!	.#	%!	#	!	*	#	!		#.	!#		 !	.#
,	0#	#	!#	!	#	#		#	*!.,
♦ 
	

0#	!...

4-44
B B
r r
i i
d d
g g
e e
   
U U
n n
i i
t t
   
( (
B B
U U
- -
5 5
0 0
0 0
0 0
) )
With this option, printed pages are sent to the Finisher/Stapler.
✒ Note
• If this Bridge unit is installed, the optional Finisher must be installed later.
• If the mailbox is already installed, remove the four mailbox trays from the
mailbox.
I I
n n
s s
t t
a a
l l
l l
i i
n n
g g
   
t t
h h
e e
   
B B
r r
i i
d d
g g
e e
   
U U
n n
i i
t t
☛
☛☛ ☛ 1.Confirm that the box also contains the following items.
Fig....

CHAPTER 4 OPTIONS
4-45
☛
☛☛ ☛ 2.Turn off the printer and remove all cables and cords from the printer.
☛
☛☛ ☛ 3.Remove the adhesive tape.
!Caution
Do not remove the adhesive tape () holding the cable and the Bridge unit,
until the Bridge unit is attached in step 14.
1
Fig. 4-73
☛
☛☛ ☛ 4.If you installed the Duplex unit, open the Duplex unit by lifting the catch.
Fig. 4-74
 

4-46
☛
☛☛ ☛ 5.Open the Right cover of the printer by lifting the catch.
Fig. 4-75
☛
☛☛ ☛ 6.Use a coin to remove the screw from the Front right cover and then remove
the Front right cover.
✒ Note
• The Front right cover has a clear film to prevent the removed screw
falling in the printer. Do not remove the screw from the film.
Fig. 4-76
• The removed screw and cover are required in step 11.
 

CHAPTER 4 OPTIONS
4-47
☛
☛☛ ☛ 7.Use a coin to remove the screw, and then remove the cover as shown in the
illustration
✒ Note
• The removed screw and cover are no longer required.
Fig. 4-77
☛
☛☛ ☛ 8.Return the Paper sensor into the Output tray as shown in the illustration.
Fig. 4-78
☛
☛☛ ☛ 9.Place the Bridge unit on the Output tray and slide the unit along the output
part of the printer.
Fig. 4-79