Brother Hl 3260n User Manual

CHAPTER 3 CONTROL PANEL
3-37
M M
M
O O
O
D D
D
E E
EM M
M
E E
E
N N
N
U U
UF F
F
a a
a
c c
c
t t
t
o o
o
r r
r
y y
y
   
 
S S
S
e e
e
t t
t
t t
t
i i
i
n n
n
g g
g
PRINT MENU
PRINT MENUPRINT MENU PRINT MENU MEDIATYPE
MEDIATYPEMEDIATYPE MEDIATYPE
=PLAIN PAPER
PAPER
PAPERPAPER PAPER
=A4/LETTER
COPIES
COPIESCOPIES COPIES
=1
ORIENTATION
ORIENTATIONORIENTATION ORIENTATION
=PORTRAIT
PRINT POSITION
PRINT POSITIONPRINT POSITION PRINT POSITION
X OFFSET=0
Y OFFSET=0
AUTO FF TIME
AUTO FF TIMEAUTO FF TIME AUTO FF...

USER’S GUIDE
3-38
M M
M
O O
O
D D
D
E E
EM M
M
E E
E
N N
N
U U
UF F
F
a a
a
c c
c
t t
t
o o
o
r r
r
y y
y
   
 
S S
S
e e
e
t t
t
t t
t
i i
i
n n
n
g g
g
IBM PROPRINTER
IBM PROPRINTERIBM PROPRINTER IBM PROPRINTER
FONT NO.
FONT PITCH/POINT
SYMBOL CHARACTER SET
TABLE PRINT
AUTO LF=OFF
AUTO CR=OFF
AUTO MASK=OFF
LEFT MARGIN
RIGHT MARGIN
TOP MARGIN
BOTTOM MARGIN
LINES
HP-GL
HP-GLHP-GL HP-GL
CHAR SET(STD)
CHAR SET(ALT)
PEN ✲ SIZE=## DOTS
PEN ✲ GRAY=## #%
BR-SCRIPT
BR-SCRIPTBR-SCRIPT BR-SCRIPT
ERROR PRINT=OFF...

CHAPTER 4 OPTIONS
4 
4C
C
H
H
A
A
P
P
T
T
E
E
R
R
 
 
4
4
O
O
P
P
T
T
I
I
O
O
N
N
S
S
 

CHAPTER 4 OPTIONS
4-1

 

 
 
 
 
 
 
 
	 	

 

 
 
 

 

 
 
 
 
 

 

	
	



	






	

	
			

	

♦ 


 

	
	 
 !
 

	
	 
 
# $
	 $% 
$ &	 

	 & 
( )
*+	
 )+ 
) ,
-	 - 
. &
 &% 
/ 0	

	 + 
0 /,$1$2
 /$ 3.*/$ (%
G FH CD
E
Fig. 4-1

 

4-2
I I
n n
s s
t t
a a
l l
l l
i i
n n
g g
   
O O
p p
t t
i i
o o
n n
s s
!Caution
• Before installing options, the machine should be turned off and
unplugged for at least thirty minutes. Components inside the machine
become very hot, and can cause a burn injury if touched.
• Before moving the machine, unplug the power cord from the outlet.
Pulling the power cord can cause damage. Damaged plugs or cords can
cause an electrical or fire hazard.
• When lifting the machine, use the handholds on both sides...

CHAPTER 4 OPTIONS
4-3
O O
p p
t t
i i
o o
n n
   
I I
n n
s s
t t
a a
l l
l l
a a
t t
i i
o o
n n
   
S S
e e
q q
u u
e e
n n
c c
e e
When you install options, they should be installed in the sequence
described below.
☛
☛☛ ☛ 1. Installing Lower paper tray
         (LT-5100 or LT-5200)There are two types of paper trays:
A 500x2 sheets paper tray (LT-5100) and a
2000 sheets paper tray (LT-5200)
Only one of them can be installed at any
time. See “Installing the Lower paper tray” in
this chapter.
☛
☛☛ ☛ 2....

4-4
L L
o o
w w
e e
r r
   
T T
r r
a a
y y
   
U U
n n
i i
t t
   
( (
L L
T T
- -
5 5
1 1
0 0
0 0
, ,
   
L L
T T
- -
5 5
2 2
0 0
0 0
) )
A lower tray unit expands the paper source capacity. You can load extra
paper and switch between the upper and lower paper sources automatically.
There are two types of paper feed units that are described below. LT-5100
can be loaded with 500 x 2 sheets.  LT-5200 can be loaded with 2000
sheets.
I I
n n
s s
t t
a a
l l
l l
i i
n n
g g
   
t t
h h
e e
   
L L
o o
w w
e...

CHAPTER 4 OPTIONS
4-5
1
2
3
ZAEP380E 
     Fig. 4-3
1. Screws (4 pieces)
2. Securing brackets (2 pieces)
3. Installation Guide
✒ Note
Tray number seal is only included with the printer.
 

4-6
☛
☛☛ ☛ 2.Turn off the printer, and remove all cables and the power cord from the
printer.
☛
☛☛ ☛ 3.Remove the adhesive tape and the packing materials.
✒ Note
Remove the adhesive tape fixing the cable to the paper feed unit after
positioning the printer.
[LT-5100]
ZAEP480E 
Fig. 4-4
[LT-5200]
ZAEP490E 
Fig. 4-5
 

CHAPTER 4 OPTIONS
4-7
☛
☛☛ ☛ 4.Slide out the four handles on both sides of the printer.
ZAEP040E 
Fig. 4-6
☛
☛☛ ☛ 5.Holding the handles, lift the printer and align the front faces of the printer
and the paper feed unit, then place the printer onto the paper feed unit.
✒ Note
• When lifting the printer, pull out the grips from the front of the printer.
Hold the grips at the front, and hold the inset grips at the rear. The printer
should be lifted by at least two people.
ZAEP600E 
Fig. 4-7
• Do not trap...