Brother Hl 3260n User Manual

4-18
☛
☛☛ ☛ 11.Open the upper right cover () of the Interchange unit and slide the
Interchange unit to the left while keeping the Upper cover right
perpendicular to the printer (). Confirm that the projection () locates in
the hole as shown in the illustration.
13
1
2
Fig. 4-26
☛
☛☛ ☛ 12.Fasten the two screws finger tight and secure the Interchange unit to the
printer. Use a coin to tighten the screws.
ZAEP161E
Fig. 4-27
☛
☛☛ ☛ 13.Close the Upper right cover of the Interchange unit.
ZAEP162E 
Fig. 4-28
 

CHAPTER 4 OPTIONS
4-19
☛
☛☛ ☛ 14.Close the Right cover by pushing the area as shown in the illustration.
ZAEP170E 
Fig. 4-29
☛
☛☛ ☛ 15.If a mailbox unit is not to be installed, attach the Interchange unit cover that
was removed in step 9. Attach the side of the cover facing the front of the
printer first () and then the other side of the cover ().
✒ Note
To attach the mailbox, go to Installing the Mailbox, Step 6.
ZAEP180E 
Fig. 4-30
☛
☛☛ ☛ 16.Attach the connector of the Interchange unit to the socket...

4-20
D D
u u
p p
l l
e e
x x
   
u u
n n
i i
t t
   
( (
D D
X X
- -
5 5
0 0
0 0
0 0
) )
After installing the Interchange unit, install the Duplex unit on the right hand
side of the printer.
The Duplex unit is an optional device that allows printing on both sides of
pages. When it is installed, you can select either duplex printing or simplex
printing from the Control panel or the printer driver. For more information
about the control panel, see “Control Panel” in Chapter 3.
If you want to duplex print,...

CHAPTER 4 OPTIONS
4-21
☛
☛☛ ☛ 1.Confirm that the box also contains the following items.
1
2
3
4
5
6
7
ZAEP382E 
Fig. 4-32
1. Holder
2. Cover of the holder
3. Socket screws (3 pieces)
4. Allen Key
5. Hook
6. Hook holder
7. Installation Guide
 

4-22
☛
☛☛ ☛ 2.Turn off the printer, and remove all cables and the power cord from the
printer.
☛
☛☛ ☛ 3.Remove the adhesive tape and the packing materials.
Fig. 4-33
☛
☛☛ ☛ 4.Remove the two small covers from the top right hand side of the
Interchange unit.
✒ Note
The removed small covers are no longer required.
ZAEP200E 
Fig. 4-34
 

CHAPTER 4 OPTIONS
4-23
☛
☛☛ ☛ 5.Use a coin to remove the two screws on the right hand side of the printer.
✒ Note
The removed screws are no longer required.
ZAEP511E 
Fig. 4-35
☛
☛☛ ☛ 6.Use the Allen Key to remove the two screws from the cover on the right
hand side of the printer and remove the cover.
✒ Note
The removed screws and cover are no longer required.
ZAEP510E 
Fig. 4-36
☛
☛☛ ☛ 7.Fit the brackets of the holder into the slots on the side of the printer and
push downwards slightly.
ZAEP210E 
Fig....

4-24
☛
☛☛ ☛ 8.Use the Allen Key to fasten the four socket screws in the order shown in the
illustration (-
) to secure the holder to the printer.
✒ Note
The order to fasten the screws is, top right, top left, bottom right and bottom
left as viewed from the right hand side of the printer. If the screws are not
fastened in that order, the duplex unit might not close completely or the
Multi-purpose tray might not work correctly.
ZAEP660E 
Fig. 4-38
☛
☛☛ ☛ 9.Remove the small cover on the right hand side of...

CHAPTER 4 OPTIONS
4-25
☛
☛☛ ☛ 10.Fit the brackets of the hook into the holes inside the cover that was removed
in Step 9. Use the Allen Key to fasten the screw to secure the hook to the
printer.
ZAEP231E 
Fig. 4-40
☛
☛☛ ☛ 11.Lower the duplex unit so that the groove in each arm of the unit locates onto
the pin inside the holder as shown in the illustration.
ZAEP250E 
Fig. 4-41
☛
☛☛ ☛ 12.Locate the hole in the support bar of the duplex unit onto the pin on the
hook that was attached in Step 10 (), and...

4-26
☛
☛☛ ☛ 13.Close the duplex unit.
✒ Note
If the duplex unit will not close completely, the holder was not installed
correctly in Steps 7 and 8. Fasten the socket screws securely in the order
described in Step 8.
ZAEP270E 
Fig. 4-43
☛
☛☛ ☛ 14.Attach the connector of the duplex unit to the socket.
ZAEP280E 
Fig. 4-44
 

CHAPTER 4 OPTIONS
4-27
☛
☛☛ ☛ 15.If the Multi-purpose tray is not attached, attach the cover of the holder. Use
the Allen key to fasten the two screws in the order as shown in the
illustration to secure the cover to the holder.
ZAEP220E 
1
2
Fig. 4-45
✒ Note
• When attaching the Multi-purpose tray, the cover of the holder is not
required.
• Keep the Allen Key in the housing inside the front cover.
ZAEP540E 
Fig. 4-46