Brother Hl 3260n User Manual

4-28
♦ 
	




 	 


   !
	


	






 
!
#$ %#&(
✒
✒✒ ✒
•)*+*,*-.*,/,,*-0-
12
*3- 
!#$ -#&(45
•2**+,,
,/---
*,60**,
5,-
0**
...

CHAPTER 4 OPTIONS
4-29
M M
u u
l l
t t
i i
- -
p p
u u
r r
p p
o o
s s
e e
   
t t
r r
a a
y y
   
( (
M M
P P
- -
5 5
0 0
0 0
0 0
) )
With this option, you can print on paper that is custom size or on thicker
types of paper. You can load up to 100 sheets of plain paper.
M M
a a
n n
u u
a a
l l
   
F F
e e
e e
d d
When you set paper in the Multi-purpose tray with the setting MANUAL
FEED=ON selected in PAPER mode, the printer loads paper first from the
Multi-purpose tray regardless of the previous feeder...

4-30
☛
☛☛ ☛ 1.Confirm that the box also contains the following items.
3
2
1
4
ZAEP430E 
Fig. 4-47
1. Holder
2. Socket screws (2pieces)
3. Allen key
4  Installation Guide
☛
☛☛ ☛ 2.Turn off the printer, and remove all cables and the power cord from the
printer.
 

CHAPTER 4 OPTIONS
4-31
☛
☛☛ ☛ 3.Remove the adhesive tape and the packing materials.
ZAEP420E 
Fig. 4-48
ZAEP530E 
Fig. 4-49
✒ Note
If the Duplex unit is already installed, the holder is no longer required. Go to
step 8.
☛
☛☛ ☛ 4.Use a coin to remove the two screws from the right hand side of the printer.
ZAEP201E 
Fig. 4-50
 

4-32
☛
☛☛ ☛ 5.Remove the two screws holding the cover on the right hand side of the
printer using the Allen key and remove the cover.
✒ Note
The two removed screws and the cover are no longer required.
ZAEP510E 
Fig. 4-51
☛
☛☛ ☛ 6.Fit the brackets of the holder into the slots in the printer and push downward
slightly.
ZAEP210E 
Fig. 4-52
☛
☛☛ ☛ 7.Use the Allen key to fasten the four screws in the order shown in the
illustration (-
) to secure the holder to the printer.
ZAEP660E 
Fig. 4-53
 

CHAPTER 4 OPTIONS
4-33
✒ Note
The order to fasten the screws is, top right, top left, bottom right and bottom
left as viewed from the right hand side of the printer. If the screws are not
fastened in that order, the Duplex unit may not close completely or the Multi-
purpose tray may not work correctly.
☛
☛☛ ☛ 8.If the Duplex unit is not installed, skip this step and go to step 9.
If the Duplex unit is installed, the plastic edges on each side of the unit must
be removed. The edges are held in place by...

4-34
☛
☛☛ ☛ 10.Use the Allen key to fasten the 2 screws to secure the Multi-purpose tray to
the holder. Fasten the screws in the order shown in the illustration. ()
ZAEP310E
Fig. 4-56
☛
☛☛ ☛ 11.Remove the adhesive tape holding the Multi-purpose tray and cable, and
attach the connector to the socket on the bottom left hand side of the back
of the printer.
ZAEP320E 
Fig. 4-57
✒ Note
• Keep the Allen key in the housing inside the front cover. Only one Allen
key can be kept in the housing.
ZAEP541E 
Fig....

CHAPTER 4 OPTIONS
4-35

 

 
 
 
 
 
 
 
	 	
 
	 	

 

 
 
 
 
 
 

 

 

 
 
 
 
 
 
 
	 	
 
 
	 	
 
 

 

 
 
 
 
 
	

 

	

 
	



		


 	










 !!#$
%&!!#
$ ! %


()

*
✒ 

• +	
,%	
!!
-

!
 ,
.


 
! /


 -

 
 ...

4-36
☛
☛☛ ☛ 1.Open the Multi-purpose tray.
ZAEY040E 
Fig. 4-59
✒ Note
• If the paper guides do not match the paper size, image skew or a paper
misfeed may occur.
• Swing out the paper support extender when using paper sizes longer
than A4 short-edge feed (220-240V models) or Letter 8½”X11” short-
edge feed (110-120V models).
☛
☛☛ ☛ 2.Lift the paper guide lever.
ZAEY210E 
Fig. 4-60
 

CHAPTER 4 OPTIONS
4-37
☛
☛☛ ☛ 3.Load the paper and adjust the paper guides to the sides of the paper.
ZAEY220E 
Fig. 4-61
✒
✒✒ ✒  Note
When you place paper on the Multi-purpose tray, note the following:
•Do not stack paper over the limit mark, otherwise image skew or paper
misfeeds might occur.
•When you set custom size or thick paper on the Multi-purpose tray, do
not stack paper above the lower limit mark of the Multi-purpose tray.
•Shuffle the paper before setting it in the tray.
•Check the print side...