Brother Hl 3260n User Manual

4-48
☛
☛☛ ☛ 10.Fasten the two Knob screws and secure the Bridge unit.
Fig. 4-80
☛
☛☛ ☛ 11.Replace the Front right cover removed in step 6, and then fasten the screw.
Fig. 4-81
☛
☛☛ ☛ 12.Close the Right cover by pushing the area as shown in the illustration.
Fig. 4-82
 

CHAPTER 4 OPTIONS
4-49
☛
☛☛ ☛ 13.If the Duplex unit is already attacked, close the unit.
Fig. 4-83
☛
☛☛ ☛ 14.Remove the adhesive tape holding the Bridge unit and cable and packing
material, and attach the connector to the socket on the right top side of the
back of the printer.
☛
☛☛ ☛ 15.Attach the securing plate as shown in the illustration.
✒ Note
The plate fastens with a screw when installing the Finisher.
Fig. 4-84
 

4-50
F F
i i
n n
i i
s s
h h
e e
r r
/ /
S S
t t
a a
p p
l l
e e
r r
   
( (
F F
S S
- -
5 5
0 0
5 5
0 0
) )
With this option, printed pages can be sorted or stapled. If you want to
install the Finisher/Stapler, contact your sales or service representative.
The optional Bridge unit must be installed before the Finisher/Stapler can be
used.
✒ Note
• See “Adding Staples” in Chapter 5.
• See “Jammed Staples” in Chapter 6.
I I
n n
s s
t t
a a
l l
l l
i i
n n
g g
   
t t
h h
e e
   
F F
i i
n n
i i
s s
h h
e...

CHAPTER 4 OPTIONS
4-51
☛
☛☛ ☛ 1.Confirm that the box also contains the following items.
Fig. 4-85
1. Installation Guide
2. Finisher
3. Finisher tray
4. Finisher stand
5. Output guide
6. Screw (2pieces)
7. Stopper (2pieces)
☛
☛☛ ☛ 2.Turn off the printer and remove all cables and the power cord from the
printer.
☛
☛☛ ☛ 3.Remove the adhesive tape.
1
Fig. 4-86
✒ Note
Do not remove the adhesive tape holding the Finisher and cable (), until
the Finisher is attached in step 10.
1
23
3456
 

4-52
☛
☛☛ ☛ 4.Insert the Output guide between the Printer and the Bridge unit.
Fig. 4-87
☛
☛☛ ☛ 5.Mount the brackets of the Finisher stand by placing them in the printer and
then push it downwards slightly with catching it on the projection of the
output guide ().
1
Fig. 4-88
☛
☛☛ ☛ 6.Use a coin to fasten the two screws that secure the Finisher stand to the
Printer.
Fig. 4-89
 

CHAPTER 4 OPTIONS
4-53
☛
☛☛ ☛ 7.Hold the Finisher with both hands and keep it horizontal. Align the holes of
the Finisher over the brackets of the Finisher stand and then push it
downwards slightly.
✒ Note
• If you do not keep the Finisher horizontal, you can not install it correctly.
In this case, remove the Finisher and reinstall it.
Fig. 4-90
☛
☛☛ ☛ 8.Insert the Finisher tray into the hole of the Finisher().
1
Fig. 4-91
 

4-54
☛
☛☛ ☛ 9.Attach the two stoppers to the lower of the Finisher output tray to lock the
tray.
Fig. 4-92
☛
☛☛ ☛ 10.Remove the adhesive tape holding the Finisher and cable and packing
material, and attach the connector to the socket on the Bridge unit.
Fig. 4-93
 

CHAPTER 4 OPTIONS
4-55
C C
o o
m m
p p
a a
c c
t t
F F
l l
a a
s s
h h
   
c c
a a
r r
d d
This printer has a slot for optional CompactFlash memory.
If you install the optional CompactFlash memory card, you can save macros
and fonts on it.
✒ Note
•Do not install or remove cards with the printer power on, as you may
lose all data from the card, or may seriously damage the card.
•For more information about the cards, consult the dealer where you
purchased the printer.
I I
n n
s s
t t
a a
l l
l l
i i
n n
g...

4-56
R R
A A
M M
   
E E
x x
p p
a a
n n
s s
i i
o o
n n
This printer has 16 Megabytes of  standard memory and 2 slots for optional
expansion memory. The memory can be expanded up to 272 Megabytes by
installing commercially available dual in-line memory modules (DIMMs). (The
standard memory fitted can vary depending on the printer model and
country.)
M M
i i
n n
i i
m m
u u
m m
   
M M
e e
m m
o o
r r
y y
   
R R
e e
c c
o o
m m
m m
e e
n n
d d
a a
t t
i i
o o
n n
( (
I I
n n
c c
l l
u u
d d
i i
n n
g g...

CHAPTER 4 OPTIONS
4-57
♦ Duplex printing
If you use the duplex function, we recommend additional DIMMs.
 300 dpi 600 dpi
HP LaserJet  standard standard
BR-Script 3  standard standard
The following capacity of DIMM can be installed:
16 Megabyte  TECHWORKS PM-HP 16M-BR
32 Megabyte TECHWORKS PM-HP 32M-BR
64 Megabyte  TECHWORKS PM-HP 64M-BR
128 Megabyte  TECHWORKS PM-HP 128M-BR
In general, the DIMM must have the following specifications:
Type: 100 pin and 32 bit output
CAS Lantency 2 or 3
Clock Frequency...