Brother Hl 3260n User Manual

4-58
I I
n n
s s
t t
a a
l l
l l
i i
n n
g g
   
a a
d d
d d
i i
t t
i i
o o
n n
a a
l l
   
m m
e e
m m
o o
r r
y y
To install additional memory (DIMMs), follow these steps:
☛
☛☛ ☛ 1.Turn off the printer and unplug the power cord from the AC outlet.
✒ Note
• Be sure to turn off the power to the printer before installing or removing
the DIMMs.
☛
☛☛ ☛ 2.Use a coin to remove the six screws and remove the Printer board cover.
✒ Note
• The removed cover and screws are required in step 6.
Fig. 4-95
☛
☛☛ ☛...

CHAPTER 4 OPTIONS
4-59
☛
☛☛ ☛ 4.Hold the DIMM with your fingers against the side edges and thumb against
the back edge. Align the notches on the DIMM with the DIMM slot. (Check
that the locks on each side of the DIMM slot are open, or outward.).
Fig. 4-97
☛
☛☛ ☛ 5.Press the DIMM straight into the slot (press firmly). Make sure the locks on
each side of the DIMM snap inwards into place. (To remove a DIMM, the
locks must be released.)
Fig. 4-98
 

4-60
☛
☛☛ ☛ 6.Attach the printer board cover that was removed in step 2, and use a coin to
fasten the six screws.
✒ Note
• If you are going to install the hard disk at the same time, it is not
necessary to reattach the cover at this stage.
Fig. 4-99
☛
☛☛ ☛ 7.Reconnect the printer cable from your computer. Plug the power cord into
the AC outlet and turn on the printer.
☛
☛☛ ☛ 8.To check whether the DIMM has been installed correctly, you may perform a
Test Print “Print Configuration” that will print the...

CHAPTER 4 OPTIONS
4-61
H H
D D
D D
   
( (
H H
a a
r r
d d
   
D D
i i
s s
k k
   
D D
r r
i i
v v
e e
) )
By installing an optional HDD, you can save multiple print jobs onto it. You
can also select your print job and re-print it through the network.
☛
☛☛ ☛ 1.Confirm that the box contains the following items.
Fig. 4-100
1. HD-6G/HD-EX
2. Hard disk cables (2) [Use the longer one]
3. Shoulder screws (4)
4. Screws (4)
5. Setup guide
☛
☛☛ ☛ 2.Turn off the printer and unplug the power cord from the AC...

4-62
☛
☛☛ ☛ 4.Use a screwdriver to remove the three screws and remove the HDD base
plate.
Fig. 4-102
☛
☛☛ ☛ 5.Insert the 4 shoulder screws supplied with the HD-6G/HD-EX unit into the
bottom of the HD-6G/HD-EX.
Fig. 4-103
☛
☛☛ ☛ 6.Fit the HDD base plate by fitting the 4 Screws into the 4 holes of the HDD
base plate and secure the base plate to the shoulder screws with a
screwdriver.
Fig. 4-104
 

CHAPTER 4 OPTIONS
4-63
☛
☛☛ ☛ 7.Connect the longer cable to the HD-6G/HD-EX with the keyed side upwards,
ensuring it is correctly aligned.
Fig. 4-105
☛
☛☛ ☛ 8.Connect the flat cable to the main controller board.
Fig. 4-106
☛
☛☛ ☛ 9.Mount the HDD base plate and HD-6G/HD-EX assembly using the 3 screws
that were removed in step 4 using a screwdriver to fasten the three screws.
Fig. 4-107
 

4-64
☛
☛☛ ☛ 10.Attach the printer board cover that was removed in step 3, and use the
screwdriver to fasten the six screws.
Fig. 4-108
☛
☛☛ ☛ 11.Reconnect the interface cable to the printer. Plug the power cord into the AC
outlet, and then turn on the printer.
☛
☛☛ ☛ 12.Format the HD-6G/HD-EX from the Control panel. See Chapter 3 for details.
 

CHAPTER 5 MAINTENANCE
5 
5C
C
H
H
A
A
P
P
T
T
E
E
R
R
 
 
5
5
M
M
A
A
I
I
N
N
T
T
E
E
N
N
A
A
N
N
C
C
E
E
 

CHAPTER 5 MAINTENANCE
5-1

 

 
 
 
 
 
 
 

	 

 	

 
 

Fig. 5-1
 
	 	

 

 
 
 

 
	 	
 
 
 
 
	


	 
!#
$ 
	
%%&(
)
%


		*+
✒
✒✒ ✒	
• 


%


%
%

+
• 

	

	
%%...

5-2
T T
O O
N N
E E
R R
   
L L
O O
W W
   
m m
e e
s s
s s
a a
g g
e e
Check printed pages, page counter and display messages periodically. If the
display shows the message below, the printer has almost run out of toner or
the toner is not evenly distributed inside the bottle.
TONER LOW
TONER EMPTY
Although you can print about 50 additional pages after the “TONER LOW”
message first appears, be sure to replace the toner bottle with a new one
before it becomes completely empty.
You can select the...