Home > Brother > Printer > Brother DCP 8045D User Manual

Brother DCP 8045D User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Brother DCP 8045D User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							OPTIONAL ACCESSORIES   15 - 2
    Installing the optional memory board
    WARNING
    ■DO NOT touch the surface of the main board within 15 minutes 
    after turning off the power.
    1Turn the DCP power switch off, unplug the DCP power cord 
    from the AC outlet, and then disconnect the interface cable.
    WARNING
    Turn the DCP power switch off, before installing (or removing) the 
    memory board.
    2Remove the side cover. Loosen the two screws, and then 
    remove the metal shield plate.
    3Unpack the DIMM and hold it by the edges.
     
    						
    							15 - 3   OPTIONAL ACCESSORIES
    WARNING
    DIMM boards can be damaged by even a small amount of static 
    electricity. Do not touch the memory chips or the board surface. 
    Wear an antistatic wrist strap when you install or remove the board. 
    If you do not have an antistatic wrist strap, frequently touch the bare 
    metal on the printer.
    4Hold the DIMM with your fingers on the side edges and your 
    thumb on the back edge. Line up the notches on the DIMM with 
    the DIMM slot. (Check that the locks on each side of the DIMM 
    slot are open or facing outwards.)
    5Press the DIMM straight into the slot (press firmly). Make sure 
    the locks on each side of the DIMM click into place. (To remove 
    a DIMM, you must release the locks.)
    6Put the metal plate back on and secure the metal plate with the 
    two screws.
    7Put the side cover back on.
     
    						
    							OPTIONAL ACCESSORIES   15 - 4
    8Reconnect any additional interface cables that you removed.
    9Reconnect the power cable and then turn on the DCP power 
    switch.
    WARNING
    If the Status LED turns Red for a Service Error, please coll Brother 
    Custome Service at: 1-800-284-4329 (in USA) or 1-877-BROTHER 
    (in Canada).
    ■To check that you have installed the DIMM correctly, print 
    the printer settings by using the selection in the driver and 
    check the printout to make sure it shows the additional 
    memory.
    ■You can check the current memory size to press 
    Menu, 1, 8 (DCP-8040) or Menu, 1, 9 (DCP-8045D).
     
    						
    							15 - 5   OPTIONAL ACCESSORIES
    Network (LAN) board
    When you add the optional Network (LAN) Board (NC-9100h), you 
    can connect your DCP into the network to use the Network Scanner, 
    Network Printer and Network Management operations.
    WARNING
    DO NOT touch the surface of the main board within 15 minutes after 
    turning off the power.
    For more details about how to configure the Network board, please 
    see the NC-9100h Network Users Guide on the CD-ROM supplied 
    with the DCP.
    NC-9100h
    Print Server
     
    						
    							OPTIONAL ACCESSORIES   15 - 6
    Before starting installation
    Be careful when handling the NC-9100h. There are many delicate 
    electronic components that are susceptible to damage from static 
    electricity. To avoid such damage, use the following precautions 
    when handling the board.
    ■Leave the NC-9100h in its anti-static bag until you are ready to 
    install it.
    ■Make sure that you are adequately grounded before touching the 
    NC-9100h. Use an anti-static wrist strap and a grounding mat if 
    possible. If you do not have an anti-static wrist strap, touch the 
    bare metal surface on the back of the machine before handling 
    the NC-9100h.
    ■Avoid moving around the work area in order to eliminate static 
    charge build-up.
    ■If possible, do not work on a carpeted area.
    ■Do not flex the board and do not touch the components on the 
    card.
    Tools Required:
    Phillips Screwdriver 
    Step 1: Hardware installation
    WARNING
    DO NOT touch the surface of the main boards within 15 minutes after 
    turning off the power.
    1Turn the DCP power switch off, unplug the DCP power cord 
    from the AC outlet, and then disconnect the interface cable.
     
    						
    							15 - 7   OPTIONAL ACCESSORIES
    WARNING
    Turn the DCP power switch off, before installing (or removing) the 
    NC-9100h board.
    2Remove the side cover. Loosen the two screws, and then 
    remove the metal shield plate.
    3Loosen the two screws, and then remove the metal cover plate.
    Cover Plate
     
    						
    							OPTIONAL ACCESSORIES   15 - 8
    4Plug the NC-9100h into connector P1 located on the main board 
    as shown in the illustration (press finmly) and secure the 
    NC-9100h with the two screws.
    5Put the metal shield plate back on and secure it with the two 
    screws.
    6Put the side cover back on.
    7Reconnect any additional interface cables that you removed.
    8Reconnect the power cable and then turn on the DCP power 
    switch. 
    9Press the Test switch and print a network configuration page. 
    (See TEST SWITCH on page 15-10.)
     
    						
    							15 - 9   OPTIONAL ACCESSORIES
    Step 2: Connecting the NC-9100h to an 
    Unshielded Twisted Pair 10BASE-T or 
    100BASE-TX Ethernet Network
    To connect the NC-9100h to a 10BASE-T or 100BASE-TX Network, 
    you must have an Unshielded Twist Pair Cable. One side of the cable 
    must be connected to a free port on your Ethernet hub and the other 
    side must be connected to the 10BASE-T or 100BASE-TX connector 
    (an RJ45 Connector) of the NC-9100h.
    Verifying successful hardware Installation:
    Plug in the AC power cord. After initialization and warm-up (this may 
    take several seconds), the DCP will come to a Ready state.
    LED
    No light:
    If both of the two LEDs are off, then the print server is not connected 
    to the network.
    Link/Speed LED is orange: Fast Ethernet
    This Link/Speed LED will be orange if the print server is connected 
    to a 100BASETX Fast Ethernet network.
     
    						
    							OPTIONAL ACCESSORIES   15 - 10
    Link/Speed LED is green: 10 BASE T Ethernet
    This Link/Speed LED will be green if the print server is connected to 
    a 10 BASE T Ethernet.
    Active LED is yellow:
    The Active LED will blink if the print server is receiving or transmitting 
    data.
    TEST SWITCH
    Short push: Prints the network configuration page.
    Long push (more than 5 seconds): Reset the network configuration 
    back to the default settings.
     
    If there is a valid connection to the network, the LED will blink 
    orange or green.
    To set up the DCP on the Network, see the NC-9100h Network 
    User’s Guide
     on the CD-ROM.
    LED
    LED Ethernet
    RJ-45
    Test 
    Switch
     
    						
    							15 - 11   OPTIONAL ACCESSORIES
    Paper Tray #2
    You can purchase the Paper Tray #2 accessory (LT-5000) to use as 
    a third paper source. Tray #2 holds up to 250 sheets of 20 lb (80 
    g/m
    2) paper.
    Paper Tray #2:Holds approx. 250 sheets of 20 lb (80 g/m2) Letter/A4 
    paper
    Basis Weight:16 to 28 lb (60 to 105 g/m
    2)
    Moisture Content:4% to 6% by weight
    We Recommend:Xerox 4200DP 20 lb
    Cut sheet:Hammermill Laser Paper 24 lb
     
    						
    All Brother manuals Comments (0)

    Related Manuals for Brother DCP 8045D User Manual