Barco Projector Toolset For Hdx Series Reference Guide

							6. Configurator, General projector settings
2. To set the retarding time, check the check box in front of the desired time.
The following settings are possible:
-1minute
-3minutes
-5minutes
- 10 minutes
Image 6-13
6.8.5 LCD, backlight intensity
What can be done ?
The intensity of the backlight of the local LCD can be adjusted.
How to adjust
1. Click onAdvanced control(1). (image 6-14)
TheAdvanced controldialog box opens (2).
2. To change the backlight intensity, click on the slider and move the slider to the left or the right until the
desired intensity is obtained.
Or,
click on the up down control of the spin box until the desired intensity is obtained.
Or,
click in the inputfield, select the current value and enter a new value with the keyboard.
R5905073 PROJECTOR TOOLSET 07/06/2011
77 
						

							6. Configurator, General projector settings
Image 6-14
Local LCD, backlight intensity
6.8.6 LCD, time out
What can be done ?
The local LCD can be switched off after a certain time when there is no activity on the local keyboard for
this period.
How to set the time
1. Click onAdvanced control(1). (image 6-15)
TheAdvanced controldialog box opens(2).
2. To change the timout, click on the slider and move the slider to the left or the right until the desired
timeout is obtained.
Or,
click on the up down control of the spin box until the desired timeout is obtained.
Or,
click in the inputfield, select the current value and enter a new value with the keyboard.
78
R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							6. Configurator, General projector settings
Image 6-15
Local LCD, timeout
Timeout value equal to zero (0) means no timeout. Content on the LCD remains visible.
6.8.7 LCD, backdrop image
What can be done ?
The backdrop image on the local LCD can be changed to any desired image as long as the resolution of
the image is 480 x 272 pixels and the format is png.
How to upload
1. WhileLCDis active, click onSelectjust belowLCD backdrop image. (image 6-16)
The requirements for the image are displayed (2).
The requirements are :
- resolution 480 x 272
- png image format
2. If you want to continue, clickYe s(3).
A browser window opens (4).
3. Browse to thefile and select the desiredfile (5).
4. ClickChoose png image(6).
R5905073 PROJECTOR TOOLSET 07/06/2011
79 
						

							6. Configurator, General projector settings
A question window opens to ask if you are sure to upload the previewed image.
5. ClickOKto upload the image (7).
The image will be uploaded.
6. To view a preview of the image, click onPreview.
To remove the image from the projector, click on the remove icon.
Image 6-16
LCD backdrop image
6.8.8 LCD, splash image
What can be done ?
The startup image on the local LCD can be changed to any desired image as long as the resolution of the
image is 480 x 272 pixels and the format is png.
How to change
1. WhileLCDis active, click onSelectjust belowLCD splash image(1). (image 6-17)
80
R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							6. Configurator, General projector settings
The requirements for the image are displayed (2).
The requirements are :
- resolution 480 x 272
- png image format
2. If you want to continue, clickYe s(3).
A browser window opens (4).
3. Browse to thefile and select the desiredfile (5).
4. ClickChoose png image(6).
A question window opens to ask if you are sure to upload the previewed image.
5. ClickOKto upload the image (7).
The image will be uploaded.
6. To view a preview of the image, click onPreview.
To remove the image from the projector, click on the remove icon.
Image 6-17
Startup screen
R5905073 PROJECTOR TOOLSET 07/06/201181 
						

							6. Configurator, General projector settings
6.8.9 Test patterns
What can be done ?
Different test patterns on various levels can be selected. Some test patterns can be configured via extra
settings.
How to select
1. Click onAdvanced control(1). (image 6-18)
TheAdvanced controldialog box opens (2).
2. Select a test pattern level (4) by checking the radio button of your choice.
The following levels are possible :
-OSD
- Input
- Output
- Formatter
Depending on the level selection, the available test patterns are different.
3. Click on the desired test pattern button (6).
The test pattern is displayed.
If there are extra settings possible for that selected pattern, the button next to the pattern contains a
green bullet.
4. To display the extra settings, press the button with the green dot (7).
The extra settings open. To activate a setting, check the check box in front of this setting (image 6-19)
Image 6-18
Test patterns
82R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							6. Configurator, General projector settings
Image 6-19
Test pattern settings
6.8.10 Miscellaneous settings, image load
What can be done ?
The way tofind and load the correct settings for the selected input source can be defined with image load.
The following options are possible:
• Automatic : correctfile will be loaded automatically.
• Manual : correctfile should be loaded manually.
• Custom only : correctfile will be loaded automatically out of the available customfiles.
How to set the image load
1. Click onAdvanced control(1). (image 6-20)
TheAdvanced controldialog box opens (2).
2. Click onMisctab (3).
3. Click on the drop down box next toImage loadand select the desired setting (4).
R5905073 PROJECTOR TOOLSET 07/06/2011
83 
						

							6. Configurator, General projector settings
Image 6-20
6.8.11 Miscellaneous settings, contrast enhancement - intensity
Purpose
Contrast : change the contrast of the projected image.
Intensity : change the brightness of the projected image.
How to adjust
1. Click onAdvanced control(1). (image 6-21)
TheAdvanced controldialog box opens (2).
2. Click onMisctab (3).
3. To change the contrast (4), click on the slider next toContrast enhancementand move it to the right or
left until the desired value is obtained.
Or,
click on the up down control of the spin box until the desired value is obtained.
Or,
click inside the inputfield, select the current value and enter the desired value with your keyboard.
4. To change the intensity (5), click on the slider next toIntensityandmoveittotherightorleftuntilthe
desired value is obtained.
Or,
click on the up down control of the spin box until the desired value is obtained.
Or,
click inside the inputfield, select the current value and enter the desired value with your keyboard.
84
R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							6. Configurator, General projector settings
Image 6-21
Contrast enhancement - intensity
6.8.12 Miscellaneous settings, calibrate lens
What can be done ?
The lens will be calibrated
How to start
1. Click onAdvanced control(1).
TheAdvanced controldialog box opens (2).
2. Click onMisctab (3).
6.8.13 Miscellaneous settings, lens settings all layouts
What can be done ?
Lens settings used for the current layout can be used for all other layouts.
How to set up
1. Click onAdvanced control(1). (image 6-22)
TheAdvanced controldialog box opens (2).
2. Click onMisctab (3).
3. Check the check box in front ofLens settings for all layouts(4).
Once checked, the same lens settings will be used for all layouts.
R5905073 PROJECTOR TOOLSET 07/06/2011
85 
						

							6. Configurator, General projector settings
Image 6-22
6.8.14 Miscellaneous settings, Auto picture alignment
What can be done ?
The auto picture alignment function can be deactivated or activated in two ways, always executed when
sync comes back after a sync loss or executed during afile load.
• Off : auto picture alignment deactivated
• Always : auto picture alignment is always activated
•Onfile Load
How to set up
1. Click onAdvanced control(1).
TheAdvanced controldialog box opens (2).
2. Click onMisctab (3).
3. Check the desired function for the auto picture alignment.
6.8.15 Miscellaneous settings, device clock
What can be done ?
The internal device clock can be set to match with the local time.
How to set the time
1. Click onAdvanced control(1). (image 6-23)
TheAdvanced controldialog box opens(2).
2. Click onMisctab (3).
86
R5905073 PROJECTOR TOOLSET 07/06/2011