Barco Projector Toolset For Hdx Series Reference Guide

							6. Configurator, General projector settings
3. To change the year, date and time, click on the corresponding up down control of the spin box until the
desired value is reached (4).
4. Click onSetto set the clock (6).
Use the refresh button the refresh the clock values (5).
Image 6-23
6.9 Maintenance
Overview
• Reset to factory defaults
• Reset electronics
6.9.1 Reset to factory defaults
What can be done?
All settings of the projector areset to the original factory settings with the exception of the IP address, serial
settings and DMX settings. For these settings, the choice exists to include them in the reset operation.
All user settings with the exception of those mentioned, are erased with this operation.
How to reset
1. Click onMaintenance(a). (image 6-24)
The Maintenance dialog box is displayed.
2. Check the items which may also be reset during the reset operation (b).
R5905073 PROJECTOR TOOLSET 07/06/2011
87 
						

							6. Configurator, General projector settings
The following items are normally exclude during a reset operation:
-IPsettings
- Serial communication settings
- DMX settings
3. Click on the buttonReset nownext toReset to factory defaults(c).
4. ClickClose.
Image 6-24
Restore factory defaults
6.9.2 Reset electronics
How to reset
1. Click onMaintenance. (image 6-25, image 6-26)
The Maintenance dialog box is displayed.
2. Click on the buttonReset nownext toReset electronics.
3. ClickClose.
Image 6-25
Reset electronics
88R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							6. Configurator, General projector settings
Image 6-26
Reset electronics
R5905073 PROJECTOR TOOLSET 07/06/201189 
						

							6. Configurator, General projector settings
90R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							7. Configurator, Projector alignment settings
7. CONFIGURATOR, PROJECTOR
ALIGNMENT SETTINGS
Overview
• Lens control
• Test patterns
• Gamma adjustment
• Individual color selection
• Blanking adjustment
•ScenergiX
7.1 Lens control
Overview
•Lensshift
• Lens mid position
• Lens zoom
• Lens focus
7.1.1 Lens shift
What can be done?
When the lenses are motorized, it is possible to adjust these lenses via the Projector Toolset. The images
can be shifted horizontally and vertically.
Image 7-1
Lens shift
How to shift the image
1. To shift the image horizontally, click on the left or right arrow button in the shift pane.
2. To shift the image vertically, click on the up or down arrow button in the shift pane.
Click on the shift buttons until the correct image position is obtained.
7.1.2 Lens mid position
What can be done?
When the lenses are motorized, it is possible to put the lens it is mid position via the Projector Toolset.
R5905073 PROJECTOR TOOLSET 07/06/2011
91 
						

							7. Configurator, Projector alignment settings
Image 7-2
How to bring to mid position
1. Click on the Center button between the shift buttons.
7.1.3 Lens zoom
What can be done?
When the lenses are motorized, it is possible to zoom these lenses via the Projector Toolset.
Image 7-3
How to zoom
1. Click on the up or down arrow button in the zoom pane.
7.1.4 Lens focus
What can be done?
When the lenses are motorized, it is possible to focus these lenses via the Projector Toolset.
Image 7-4
How to focus
1. Click on the up or down arrow button in the focus pane.
92
R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							7. Configurator, Projector alignment settings
Click until the correct focus is obtained.
7.2 Test patterns
What can be done?
A predefined pattern can be set immediately on the projection screen and cleared again. This can be
done via short cuts or via other internal patterns. Extra settings for the internal patterns can be set.
To select a short cut pattern
1. Click on one of the predefined buttons. (image 7-5)
The selected pattern is displayed by the projector when the lamp is on and the shutter is open (not
paused).
The following patterns are available:
- Full screen red
- Full screen green
- Full screen blue
- Full screen white
- Full screen black
- Checkerboard
- Color bars
For more patterns, click onOthers.
2. To clear a projected pattern, clickClear.
Image 7-5
To select other input test patterns
1. Click onOthers(1). (image 7-6)
The input test pattern selection window opens.
2. Click on a test pattern button (2) to activate the pattern.
If there are extra settings available for that selected test pattern, then the button next to the test pattern
name will have a green dot.
3. To set these extra settings, click on the button with thegreen dot (3).
4. Check the check boxes of the desired settings
R5905073 PROJECTOR TOOLSET 07/06/2011
93 
						

							7. Configurator, Projector alignment settings
Image 7-6
7.3 Gamma adjustment
About Gamma
Gamma is an image quality enhancement function that offers a richer image by brightening the already
darker portions of the image without altering the brightness of the brighter portions (contrast feeling en-
hanced).
Image 7-7
Gamma adjustment
Adjusting via dragging
1. Click on the slider bar of the gamma adjustment and hold down the mouse button.
2. Move the slider until the desired value is reached.
The value in the inputfield of the spin box will change accordingly.
94
R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							7. Configurator, Projector alignment settings
Adjusting via the up down controls
1. Click on the up down control of the spin box of the gamma adjustment until the desired value is reached.
The value in the inputfield change accordingly.
Adjusting via the inputfield
1. Click inside the inputfield of the spin box of the gamma adjustment.
2. Select the actual value and enter a new value with the keyboard.
7.4 Individual color selection
What can be done?
Theprojectorcanbeforcedtodisplayatypicalcolororallcolors.
Color selection
1. Click on the radio button of your choice. (image 7-8)
The selected color is displayed on the screen.
The following can be selected:
-allcolors
-redonly
- green only
-blueonly
Image 7-8
7.5 Blanking adjustment
What can be done ?
Blanking adjustments affect only the edges of the projected image and are used to frame the projected
image on to the screen and to hide or black out unwanted information (or noise). A ’0’ on the bar scale
indicates no blanking.
Blanking is limited to half the resolution of the projector.
R5905073 PROJECTOR TOOLSET 07/06/2011
95 
						

							7. Configurator, Projector alignment settings
Which blanking adjustments are available ?
• top blanking
• bottom blanking
• left blanking
• right blanking
Image 7-9
Blanking
A Top blanking
B Bottom blanking
C Left blanking
D Right blanking
How to adjust a side blanking
1. Click on the up down control of the spin box of the desired blanking until the chosen blanking is correctly
set up.
Or,
click in the inputfield of the spin box of the desired blanking and enter the desired blanking value.
(image 7-10)
The preview shows the setup blanking for each side.
96
R5905073 PROJECTOR TOOLSET 07/06/2011