Avaya Partner Advanced Communications System Installation, Programming And Use Manual

Programming System Options
System Reset–Programming Saved (#728)
4-55
System Reset–Programming Saved (#728) 
Use this feature to reset the system while retaining the currently programmed settings. Reset the 
system only when advised to do so by technical support personnel.
Considerations

Resetting the system disconnects all active calls.

This procedure is skipped in the sequence of programming procedures when cycling. To use 
this procedure, enter the code directly.

The system reset begins immediately...

PA R T N E R® Advanced Communications System Installation, Programming, and Use
System Speed Dial
4-56
System Speed Dial 
Program a list of up to 100 frequently-dialed numbers for the system by using System Speed Dial. 
After you have programmed the numbers, anyone on the system can dial a System Speed Dial 
number by pressing 
f (or # at intercom dial tone on a single-line telephone) and the three-
digit code, from 600 through 699, for that number. You can mark System Speed Dial numbers to 
override...

Programming System Options
Toll Call Prefix (#402)
4-57

You can use multiple Auto Dial buttons and Speed Dial numbers during the course of a single 
call. For example, you can use an Auto Dial button or Speed Dial number to dial the Account 
Code Entry feature code, and another Speed Dial number to dial the account code.
Programming
To  p r o g r a m  System Speed Dial numbers:
1. Press 
f00 at extension 10 or 11.
2. Select a three-digit code by pressing 
f and dialing three digits between 600 and 699....

PA R T N E R® Advanced Communications System Installation, Programming, and Use
Transfer Return Programming
4-58
Programming
To change the Toll Call Prefix setting:
1. Press 
f00ss#402 at extension 10 or 11. 
2. Press 
D until the appropriate value appears:

1 = 0 or 1 required before Area Code and Number (the factory setting) ✔ 

2 = Area Code and Number Only
3. Select another procedure, or exit programming mode.
Transfer Return Programming
By the factory setting, transferred calls return to the...

Programming System Options
Transfer Return Programming
4-59

For transferred calls that are sent to a covering extension with Call Coverage: if the covering 
extension does not answer within the specified number of Call Coverage Rings (#116) or 
(#320), the call rings the specified number of Transfer Return Rings (#105) before it transfer 
returns. If the covering extension has Do Not Disturb active, the call rings one more time after 
the specified number of Call Coverage Rings (#116) or (#320) before...

PA R T N E R® Advanced Communications System Installation, Programming, and Use
Unique Line Ringing (#209)
4-60
Unique Line Ringing (#209)
Use this feature to assign a ringing pattern (maximum of eight) to a line for users to differentiate, 
by sound, which line is ringing. Once a ring pattern is assigned to a line, incoming calls on that line 
ring with the assigned ring pattern. Incoming calls that are transferred to another station ring with 
the assigned ring pattern followed by two “transfer beeps.”...

Programming System Options
Voice Interrupt On Busy (#312)
4-61
Voice Interrupt On Busy (#312) 
Use this feature to identify extensions that can receive Voice Interrupt On Busy calls. A Vo i c e  
Interrupt On Busy call is a special intercom call that lets a user (the originator) interrupt and 
speak to another user (the recipient) who is busy on an intercom or outside call. When Vo i c e  
Interrupt On Busy is initiated, the recipient hears two beeps before hearing the originator’s voice. 
The third...

PA R T N E R® Advanced Communications System Installation, Programming, and Use
Voice Interrupt On Busy (#312)
4-62
Programming
To change the Voice Interrupt On Busy setting for an extension:
1. Press 
f00ss#312 at extension 10 or 11. 
2. Enter the number of the extension to be programmed with this feature.
3. To assign or unassign Voice Interrupt On Busy, press 
D until the appropriate value 
appears.

1 = Assigned

2 = Not Assigned (the factory setting) ✔ 
4. Select another procedure, or exit...

Contents
5-i
5
Initial Telephone Programming
Overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   5-1
Required Telephone Programming  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   5-2
Automatic Line Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   5-2

Considerations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

PA R T N E R® Advanced Communications System Installation, Programming, and Use
5-ii