Home > Amanda > Communications System > Amanda Work Group Installation Manual

Amanda Work Group Installation Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Amanda Work Group Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 32 Amanda manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Chapter 5:
    Installing Amanda Software
    Running the Installation Program
    Install Amanda software only after you have:
     Installed the voice boards.
     (Voice server only) Installed an NE2000-compatible Ethernet LAN 
    card.
    Follow the installation checklist that is in the chapter that explains how to 
    configure the voice boards you use:
     “Chapter 2: Installing RDSP/x32 Boards”
     “Chapter 3: Installing RDSP/RTNI Boards”
    If you are installing Amanda as a voice server, have your MS Workgroup 
    Add-on for DOS disk at hand.
    To start the Amanda installation program:
    1. Insert the disk labeled “[email protected]/DOS, Installation Disk 1 
    of 5” into a floppy disk drive.
    2. From the DOS prompt C:\>, type the command:
    A:\INSTALL
    (If the disk is in drive B:, use B:\INSTALL B:.)
    Then press Enter. 
    						
    							40 Installing [email protected]/DOS
    You see a screen similar to the following:
                                                                       
    Correct operation of an Amanda Call Processing system depends on accurate
    time and date settings in the computer.  To assure correct operation,
    please verify these now. Here are the present time and date:
    Current time is  3:13:04.99p
    Current date is Tue 01-14-1997
    Are these values correct[N,Y]?
                                                                       
    3. Type Y for Yes or N for No.
    If you type Y, proceed to step 4.
    If you type N, you are prompted for a new date and time, similar to what 
    is shown below. 
    a. Type a new date then press Enter or just press Enter to keep the 
    current date. 
    b. Type a new time then press Enter or just press Enter to keep the 
    current time. 
                                                                       
    Please correct the Time and/or Date now.
    Current date is Tue 01-14-1997
    Enter new date (mm-dd-yy): 01-14-97
    Current time is  3:14:36.11p
    Enter new time:
                                                                        
    						
    							Chapter 5: Installing Amanda Software 41
    Information similar to the following appears on the screen.
                                                                       
    This program installs or un-installs [email protected]/DOS
        Version 7.xx Revision X on your computer system.
        You may press the [Esc] key at any time to stop
        the installation.
        PLEASE NOTE:  This installation stores backup copies of any files
                      that it overwrites on your hard disk.  If after
                      installing you wish to revert to your previous
                      system, run this install program again and select
                      the Un-install ... option.
              
                Press [Esc] to quit, any other key to continue ...  
     
                                                                       
    4. Press any key on the keyboard to continue.
    An installation, reinstallation, or an update menu appears.
    INSTALLATION MENU
                                                                       
       Select the type of installation that you want to be performed.
       Use the arrow keys to make a selection; then press Enter.
                 Install [email protected]/DOS Version 7.xx Revision X  
                 Test the configuration of this system only         
                 Exit this installation program now                 
                                                                        
    						
    							42 Installing [email protected]/DOS
    REINSTALLATION MENU
                                                                       
          [email protected]/DOS Version 7.xx Revision X is already
          installed on this machine.
          Select the action that you want to be performed.
          Use the arrow keys to make a selection; then press Enter.
          Re-install [email protected]/DOS Version 7.xx Revision X              
          Un-install the existing [email protected]/DOS 7.xx Revision X system  
          Test configuration of this machine only                           
          Exit this installation program now                                
                                                                       
    UPDATE MENU
                                                                       
          [email protected]/DOS Version 7.xx Revision X using RH-RDSP
          style boards appears to be installed on this machine.
          Select the type of installation that you want to be performed.
          Use the arrow keys to make a selection; then press Enter.
                   Update existing [email protected]/DOS 7.xx Rev. X  
                   Test configuration of this machine only        
                   Exit this installation program now             
                                                                       
    5. In any case, select the first option on the menu then press Enter.
    If this is a new installation, go to step 6. Otherwise, go to step 7. 
    						
    							Chapter 5: Installing Amanda Software 43
    6. You see a screen similar to the following:
                                                                       
       Since this a first time installation, [email protected]/DOS needs to know
       if this system uses Brooktrout RDSP/x32 or RDSP/x000 with RTNI-xATI
       style boards. Make this choice very carefully since this choice is
       PERMANENT!
       Select the Brooktrout board type for this installation from the list.
       Use the arrow keys to make a selection; then press Enter.
                  Brooktrout RDSP/x32 style two or four port boards   
                  Brooktrout RDSP/x000 with RTNI-xATI style boards    
                  I am not sure; stop so I can find out first       
                                                                       
    Use the arrow keys to select the appropriate style of Brooktrout voice 
    board then press Enter.
    7. The next screen asks whether you are installing Amanda as a standalone 
    system or as a voice server. 
    						
    							44 Installing [email protected]/DOS
                                                                       
       [email protected]/DOS can be installed as a networked Voice Server,
       integrated with a local area network (LAN), or as a stand-alone system.
       If you elect the Voice Server installation, you must have a properly set
       NE2000 compatible Ethernet LAN adaptor installed in this machine prior to
       installing this software.
       [If you install the LAN adaptor, it MUST be set for IRQ 10 and I/O
       address 340, AND you MUST have your MS WORKGROUP ADD-ON FOR DOS disk]
       Select the type of configuration that you want to be performed.
       Use the arrow keys to make a selection; then press Enter.
        
            No LAN card.  Configure Stand-alone system.                  
            The LAN card is installed.  Configure Voice Server system.   
            Exit.  I need to install the LAN card first.                 
        
                                                                       
    If you plan to use Amanda client software to configure Amanda and 
    allow users to access messages from their computers as well as their 
    telephones, you need to install Amanda as a voice server, select the sec-
    ond option “The LAN card is installed. Configure Voice Server system.” 
    If you plan to configure Amanda from this computer and allow users to 
    access messages only from their telephones, select the first option “No 
    LAN card. Configure Stand-alone system.”
    8. The next few screens display information about your computer and the 
    installation. Follow the directions on the screen. 
    If everything is OK, the installation can continue. Otherwise, the instal-
    lation stops.
    The first screen of the following examples appears only for new installa-
    tions. If you are installing Amanda as a standalone system, some screens 
    will have less information than the examples. 
    						
    							Chapter 5: Installing Amanda Software 45
                                                                       
      Since this is a new installation, a new CONFIG.SYS file will be
      created; you do not need to take any action yourself.
     
               Press [Esc] to quit, any other key to continue ...   
                                                                       
                                                                       
    Checking your computer for the proper components and conflicts . 
    . .
    Verifying computer processor type  . . .  OK
    Verifying the video adaptor type . . . .  OK
    Verifying total amount of memory . . . .  OK
    Verifying total conventional memory. . .  OK
    Verifying operating system version . . .  OK
    Verifying sufficient free disk space . .  OK
     
             Press [Esc] to quit, any other key to continue ...  
     
                                                                        
    						
    							46 Installing [email protected]/DOS
                                                                       
      Please note that you have the following additional components . . .
      Serial port COM1 at address  : 1016
      Serial port COM2 at address  : 760
      Serial port COM3 at address  : 744
      Parallel port LPT1 at address: 888
      Video Adaptor Card type      : VGA (Video Graphics Array)
      Video Monitor Display type   : Color
      Available disk space         : 176295936
     
               Press [Esc] to quit, any other key to continue ...  
     
                                                                       
                                                                       
          Your original installation of [email protected]/DOS 7.xx Revision X
          is nearly finished.
          The system will next reboot and the initial memory configuration
          will begin.
          Next, the network portion of the Voice Server will be installed.
          Finally, since this is a new installation, the SETUP program will
          run automatically to create a configuration file with all default
          values for you.  Last, the system will reboot again and Amanda
          will be started.
      REMOVE INSTALLATION DISK 5 of 5 FROM DISK DRIVE.
      Press any key to continue ...
                                                                       
    If the installation proceeds, you will be asked to insert each of the five 
    installation disks into your floppy disk drive in order. 
    						
    							Chapter 5: Installing Amanda Software 47
    If you selected a networked Voice Server installation, you will also be 
    asked to install the MS-NETWORK files required to connect your 
    [email protected]/DOS Voice Server to the network. You will be 
    asked to remove the disk labeled “Microsoft Workgroup Add-On for 
    MS-DOS, Disk 1 - Setup” from its sealed envelope and insert it in your 
    floppy disk drive. 
    Opening the sealed envelope indicates your acceptance of the Microsoft 
    software license terms shown on the inside cover of the User’s Guide 
    for Microsoft WORKGROUP ADD-ON MS-DOS included in your pack-
    age.
    During the installation process, your computer will reboot once or 
    twice.
    9. Follow the directions on the screens. Eventually, a screen informs you 
    that “This completes the installation….”
    N
    OTE:If this is an upgrade or a reinstallation, the installation pro-
    gram does not update your existing CONFIG.SYS file. 
    However, it suggests that you change your CONFIG.SYS 
    to work better with Amanda. 
    It recommends that you reset the DOS environment mem-
    ory size to an amount based on the information you provid-
    ed about ports during the installation. 
    For example, if the program suggests a setting of 346, you 
    should add or change the /E parameter in your SHELL 
    statement. It might look like the following:
    SHELL=C:\COMMAND.COM /E:346 /P
    The installation program also suggests that you remove the 
    EMS memory limit allocated for your memory manager (if 
    that manager is EMM386.EXE). 
    For example, suppose the DEVICE statement for 
    EMM386.EXE is similar to the following:
    DEVICE=C:\DOS\EMM386.EXE 272 …
    You remove the 272. The EMS memory limit is the only 
    solitary number in the DEVICE statement.
    10. Set up Amanda to work with your telephone switching system and 
    according to your voice mail preferences.
    Use the next few chapters to define dial codes, define tone and integra-
    tion patterns, and set Amanda’s configuration options. 
    						
    							48 Installing [email protected]/DOS
    Updating Amanda
    If you are upgrading Amanda software, the installation screens are somewhat 
    different from the new installation described above. Follow the directions on 
    the screen, and the installation process should go smoothly.
    If the installation program recommends changes to your CONFIG.SYS file, 
    you need to make these changes yourself. The installation program does 
    NOT create a new CONFIG.SYS file for you because commands you added 
    or changed to run your system could be replaced.
    If you installed Amanda as a standalone only, change C:\CONFIG.SYS, the 
    CONFIG.SYS file in the root directory.
    If you installed Amanda as a voice server, make the recommended changes 
    to both C:\AMANDA\DOSMODE\CONFIG.SYS and 
    C:\AMANDA\NETMODE\CONFIG.SYS. Depending on the mode in which 
    you run Amanda, the CONFIG.SYS file (and other files) are copied to the 
    root directory (C:\) from either C:\AMANDA\DOSMODE or 
    C:\AMANDA\NETMODE. Changing the CONFIG.SYS in the root 
    directory only is like not changing the file at all because it will be replaced 
    every time you start Amanda. 
    						
    All Amanda manuals Comments (0)

    Related Manuals for Amanda Work Group Installation Manual