Yamaha Cl 5 User Guide

Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
 Reference Manual
151
Buss Comp 369Buss Comp 369 emulates a standard bus compressor that has been used in recording studios 
and broadcasting stations since the 1980s. It produces a smooth and natural compression 
that does not interfere with the expression in the source signal, in contrast with the aggressive 
compression of the U76. Buss Comp 369 includes both a compressor and a limiter. You can 
use both functions individually or in combination,...

Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
 Reference Manual
152
6
COMP GAIN
Compressor make-up gain. Applied before the limiter.
7
COMP RATIO
Compressor ratio
8
METER SELECT (STEREO mounting)
Selects the signal source for the meter. You can select from IN (input level), GR (gain 
reduction), and OUT (output level). When the source is switched, the design of the 
meter also switches as follows: VU/GR/VU.
When“METER” is IN
When“METER” is GRWhen“METER” is OUT
9
VU SELECT (DUAL mounting)
Selects...

Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
 Reference Manual
153
Using the graphic EQ, parametric EQ, effect, and 
Premium Rack librariesGEQ/PEQ libraryUse the “GEQ library” or “PEQ library” to store and recall GEQ and PEQ settings. All GEQ 
and PEQ units used in the CL series console can use this GEQ library or PEQ library. 
Although are two types, 31BandGEQ and Flex15GEQ in the GEQ library, you are free to recall 
items between differing types. However, only 31BandGEQ settings that use less...

I/O devices and external head amps
 Reference Manual
154
I/O devices and external head ampsThis chapter explains how to use an I/O device or an external head amp that is connected to 
the CL series console. Before you proceed, use DANTE SETUP to specify the I/O devices 
that will be mounted. For details, refer to “Mounting an I/O device on the Dante audio network” 
(page 231).Using an I/O deviceCL series consoles enable you to remotely control channel parameters of an I/O device (such 
as an R series...

I/O devices and external head amps
 Reference Manual
155
DANTE INPUT PATCH windowDisplayed when you press the DANTE INPUT PATCH button in the I/O DEVICE screen 
(DANTE PATCH page). Specify the 64 channels that will be input from the I/O devices to the 
console.1
LIBRARY button
Enables you to store or recall the DANTE INPUT PATCH settings to or from the library. 
You can store ten sets of settings in the library.
2
AUTO SETUP button
The current I/O device connection status will be ascertained, and input...

I/O devices and external head amps
 Reference Manual
156
OUTPUT PATCH windowDisplayed when you press the device in the I/O DEVICE screen (DANTE PATCH page). Set 
the output patch.1
Port select buttons
Press one of the buttons to open the PORT SELECT popup window.
Remotely controlling an R series unitThis section explains how to remotely control an R series unit that's connected to the Dante 
connector.
I/O DEVICE screen (I/O page)1
Display switch buttons
Press one of these buttons to view the...

I/O devices and external head amps
 Reference Manual
157
HA displayThis shows the HA settings of the I/O device. Press this area to open the I/O DEVICE HA 
window, in which you can make detailed head amp settings.
If you press the [SEL] key of an input channel, the corresponding port will light. (It does not 
light for external CL series consoles.)5
Analog GAIN knob
Indicates the analog gain setting. This screen is only for display; the value cannot be 
edited.
6
+48V indicator
Indicates the phantom...

I/O devices and external head amps
 Reference Manual
158
5
MADI STATUS INPUT status
MADI STATUS OUTPUT status
Display information regarding the MADI input and output signals (frame frequency/
number of channels).
6
WORD CLOCK WCLK IN indicator
WORD CLOCK MADI indicator
WORD CLOCK DANTE indicator
WORD CLOCK WCLK IN/MADI/DANTE buttons
Used to select the word clock source.
7
WORD CLOCK Fs indicator
Indicates the word clock frequency at which the unit is operating. Flashes when not 
synchronized.
8
EXTERNAL...

I/O devices and external head amps
 Reference Manual
159
Remotely controlling from the input channelsTo remotely control the I/O device's head amp from an input channel of the CL series console, 
operate the GAIN/PATCH window for the channel for which you want to control.Remotely controlling an ampThis section explains how to remotely control an AMP unit that's connected to the Dante 
connector.
I/O DEVICE screen (AMP page)1
Display switch buttons
Press one of these buttons to view the...

I/O devices and external head amps
 Reference Manual
160
Remotely controlling WIRELESS unitThis section explains how to remotely control a WIRELESS unit that's connected to the Dante 
connector.I/O DEVICE screen (WIRELESS page)1
Display switch buttons
Press one of these buttons to view the corresponding I/O device.
For more information about VIRTUAL/CONFLICT/DUPLICATE displayed below this 
button, refer to (1) on P.154, “I/O device list.” 
2
ID/Model name display
This shows the ID number, model name,...