Yamaha Cl 5 User Guide

Recorder
 Reference Manual
181
Setting up Dante ControllerConnect the network port of the computer to a GbE-compatible network switch. Configure the 
computer to obtain an IP address automatically (this is the default setting).
You must make the following settings for Dante Controller.
• For multi-track recording, patch audio signals from the I/O device to DVS or the Dante 
Accelerator card.
• For virtual sound check: Patch audio signals in such a way that they will be output from the 
computer to the...

Recorder
 Reference Manual
182
Using the CL console with Nuendo LiveThe CL series consoles can operate in an integrated manner with Steinberg's Nuendo Live 
DAW software.
The “Yamaha Console Extension” software which integrates the CL series and Nuendo Live 
can be installed in your computer, allowing you to operate Nuendo Live from the CL series 
console to easily perform multi-track recording operations.
Here we explain how to operate Nuendo Live from the CL series console.Preparing the...

Recorder
 Reference Manual
183
Transport fieldHere you can operate the transport of Nuendo Live.7
GO TO PROJECT START button
Returns the location to the start of the project.
8
GO TO PREVIOUS MARKER button
Returns the location to the previous marker.
9
GO TO NEXT MARKER button
Advances the location to the next marker.
0
GO TO PROJECT END button
Advances the location to the end of the project.
A
CYCLE button
Turns repeat on/off for the project.
B
STOP button
Stops playback/recording of the project.
C...

Recorder
 Reference Manual
184
1
Setup method select buttons
Choose one of the following methods by which to specify DVS or Dante Accelerator.
•NO ASSIGN........................ Not assigned
•DVS..................................... Select a DVS from the device list
•SPECIFIED IP ADDRESS.. When using Dante Accelerator, specify the IP address of 
the computer
When setup method selection button = DVSTo choose from a list of the I/O devices on the Dante audio network, press the DVS button to 
display the...

Recorder
 Reference Manual
185
NOTE• Depending on the firmware version, Dante Accelerator might not support redundant networking. 
Refer to the following website to check whether your version of the Dante Accelerator firmware 
supports redundant networking.
http://www.yamahaproaudio.com/
Playing a multi-track project
NOTEIf you save the DANTE INPUT PATCH settings in a library, the settings of the CL series console 
can be switched conveniently (page 155).
STEP
1.Press the DANTE INPUT PATCH button in the...

Setup
 Reference Manual
186
SetupAbout the SETUP screenThe SETUP screen enables you to set various parameters that apply to the entire CL console. 
To access the SETUP screen, press the SETUP button in the Function Access Area. The 
screen contains the following items.CURRENT USER fieldThis field enables you to make various user-related settings.1
USER SETUP button
Press this button to open the USER SETUP window, in which you can make various 
settings for each user.
2
CURRENT USER button
Press this...

Setup
 Reference Manual
187
BUS SETUP fieldThis field enables you to make bus-related settings.D
BUS SETUP button
Press this button to open the BUS SETUP window, in which you can make MIX bus/
MATRIX bus-related settings.
E
SURROUND SETUP button
Press this button to call up the SURROUND SETUP screen. In this screen, you can switch 
the bus settings from Stereo mode to Surround mode. If set to Stereo mode, the bus 
settings for MIX1-6 will be grayed out. If you press the 5.1 SURROUND button to switch 
to...

Setup
 Reference Manual
188
If you set Surround mode, the BUS SETUP screen appears as shown below.
DATE/TIME buttonPress this button to open the DATE/TIME window, in which you can set the date and time.NETWORK buttonPress this button to open the NETWORK window, in which you can set the network address.Indicator fieldThis field displays various information about the console.F
BATTERY indicator
Indicates the status of the internal battery.
NOTEThe LOW or NO indication will appear if the battery runs...

Setup
 Reference Manual
189
User types and user authentication keysThere are three types of user, as follows. To operate the CL series console, you must log-in 
as a user.
• Administrator ...... The administrator of the CL console can use all of its functionality. 
Only one set of Administrator settings is internally maintained in the 
console. The Administrator can create user authentication keys for 
other users.
•Guest
...... A Guest can use only the range of functionality permitted by the...

Setup
 Reference Manual
190
CREATE USER KEY window1
USER NAME
Displays the user name. Press this area to access a keyboard window, in which you can 
enter a user name of up to eight characters.
2
COMMENT
Displays a comment about the user. Press this area to access a keyboard window, in 
which you can enter a comment of up to 32 characters.
3
PASSWORD
Enables you to specify a password. Press this area to access a keyboard window, in which 
you can enter a password of up to eight characters.
4
POWER USER...