Yamaha Cl 5 User Guide

Setup
 Reference Manual
201
MONITORSOURCE SELECTSTEREO L/R
Recall the selected signal to the monitor. MONO (C)
LCR
PB OUT
OMNI1-2
OMNI3-4
OMNI5-6
OMNI7-8
DEFINE
SURROUND SOURCE 
SELECT*6)Recall the selected signal to the surround 
monitor.
SURROUND DOWN-
MIXSTEREO MONOWhen this function is off (the lamp is off), the 
setting returns to 5.1 monitor.
SURROUND SPEAKERSOLOWhen this function is on (the lamp is on), the 
SURROUND MONITOR screen opens. When this 
function is off (the lamp is off), the SURROUND...

Setup
 Reference Manual
202
SENDS ON 
FADERMIX1-MIX24
NORMAL/WITH CUEThis function switches between the normal 
function on/off (NORMAL), and the function 
with cue on/off (WITH CUE). With the WITH 
CUE option, cue will be enabled if SENDS ON 
FADER mode is engaged or if you switch mode 
during SENDS ON FADER mode. Also, with the 
WITH CUE option, cue for all output channels 
will be canceled if SENDS ON FADER mode is 
disengaged. MTRX 1-MTRX 8
MIX ON FADER
MATRIX ON FADER
SENDS ON FADER
SET BY SEL+48V...

Setup
 Reference Manual
203
*1) CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1L-ST IN 8R, MIX1-MIX24, MTRX1-MTRX8, ST L, ST 
R, MONO
*2) CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1-ST IN 8, MIX1-MIX24, MTRX1-MTRX8, STEREO, 
MONO(C)
*3) MIX1-MIX24, MTRX1-MTRX8, ST L, ST R, MONO
*4) CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1-ST IN 8, MIX1-MIX24, MTRX1-MTRX8, STEREO, 
MONO(C), DCA1-DCA16
*5) SELECTED CH, CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1L-ST IN 8R
*6)...

Setup
 Reference Manual
204
NOTE• If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access 
the USER DEFINED KNOBS and ASSIGNABLE ENCODER for Guest page and make USER 
DEFINED knob settings for the Guest account.
• The 4 knobs in the USER DEFINED KNOBS and ASSIGNABLE ENCODER page correspond to 
USER DEFINED knobs [1]-[4] on the top panel. The name of the function or parameter assigned 
to each knob appears to the right of the corresponding button. If nothing is...

Setup
 Reference Manual
205
*1) SELECTED CH, Automixer ch1-16
*2) SELECTED CH, CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1-ST IN 8, MIX1-MIX24, MTRX1-
MTRX8, STEREO, MONO (C)
*3) SELECTED CH, CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1L-ST IN 8R
*4) SELECTED CH, CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1-ST IN 8
*5) SELECTED CH, CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1L-ST IN 8R, MIX1-MIX24
*6) MIX1-MIX24, MTRX1-MTRX8, ST L, ST R, MONO
*7) SELECTED CH,...

Setup
 Reference Manual
206
Assignable encodersYou can assign the desired function to the GAIN/PAN/ASSIGN knob on the fader strip of each 
channel, and control the function using the knob. For details on the assignable functions and 
their parameters, refer to “Functions that can be assigned to the assignable encoders” 
(page 207).
NOTE
• If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access 
the USER DEFINED KNOBS and ASSIGNABLE ENCODER for Guest page and make...

Setup
 Reference Manual
207
Functions that can be assigned to the assignable 
encoders
*1 Preference setting and the state of the ALTERNATE function will determine whether this will be analog gain or 
digital gain.
*2 The send destination that is the target of Sends On Fader will be selected.
*3 The state of the ALTERNATE function will determine whether turning the encoder will switch the PRE/POST 
setting of the corresponding send or will switch the corresponding send on/off when pressed.
*4 The state...

Setup
 Reference Manual
208
GAIN/PAN/ASSIGN knob (assignable encoder) 
functionsIn CL V1.7 and later, the following functions have been added to SENDS ON FADER mode.When using the [GAIN/PAN/ASSIGN] keys on the top panel to select 
ASSIGNUse assignable encoders to adjust the level of channels.
Channel name display indicationWhen using the [GAIN/PAN/ASSIGN] keys on the top panel to select 
PA NUse assignable encoders to adjust PAN sent from channels to the MIX/MATRIX bus (bus set 
for Stereo send in the...

Setup
 Reference Manual
209
USER SETUP screen
(CUSTOM FADER BANK/MASTER FADER page)CUSTOM FADER BANK/MASTER FADER field
1
Bank select buttons
Enable you to select a custom fader bank to which you want to assign a group of 
channels.
The number and name of the custom fader banks vary depending on the console 
model.
CL5: A1, A2, B1, C1, C2, C3, C4, C5, C6
CL3: A1, A2, A3, B1, B2
CL1: A1, B1, B2, B3, B4
2
MASTER button
Press this button to set channels that will be controlled by the faders in the Master...

Setup
 Reference Manual
210
Custom fader bank functionsCustom fader bank settings can be stored/recalled for individual scenes.
Custom fader bank settings are stored in scene data in separate regions for each model.
NOTE
Custom fader bank settings differ between models, and are not compatible. For example, custom 
fader bank settings included in scenes stored in CL5 cannot be reproduced if that same scene is 
recalled in CL3 or CL1. You must create and store custom fader bank settings in CL3 and CL1....