Yamaha Cl 5 User Guide

Setup
 Reference Manual
231
Mounting an I/O device on the Dante audio networkHere's how to select which of the multiple I/O devices on the Dante audio network will be 
mounted so that they can be used. Up to 24 units can be mounted for one CL series console.DANTE SETUP window (DEVICE MOUNT page)1
CLEAR ALL button
Clears all I/O devices in the list to an unmounted state.
2
REFRESH button
Updates the displayed list of I/O devices on the Dante audio network.
3
I/O device select buttons
Press one of the...

Setup
 Reference Manual
232
When the setup method select button is DEVICE LISTTo mount by choosing from a list of the I/O devices on the Dante audio network, press the 
DEVICE LIST button to display the DEVICE LIST field.1
DEVICE LIST
Shows a list of the I/O devices on the Dante audio network.
From the list, choose the I/O device that you want to mount.
2
DEVICE LIST select knob
Use the [TOUCH AND TURN] knob to select the I/O device that you want to mount.
3
INPUT/OUTPUT knobs
Use the [TOUCH AND TURN]...

Setup
 Reference Manual
233
NOTE• If there is one I/O device, set the I/O device's UNIT ID to “1.”
• If multiple devices are connected, assign the ID numbers so that there is no conflict between 
devices.
• For devices other than the R series, it is possible for devices of differing models to be assigned 
to the same ID as an R series unit or the same ID as a different model of device. However, since 
the I/O device input/output port screen shows the UNIT ID, this will make it difficult to...

Setup
 Reference Manual
234
REMOTE HA settingsHere's how to select which of the multiple HA devices on the Dante audio network will be 
mounted so that they can be used. Up to 8 units can be mounted for one CL series console.DANTE SETUP window (REMOTE HA page)1
CLEAR ALL button
Clears all HA devices in the list to an unmounted state.
2
REFRESH button
Updates the displayed list of HA devices on the Dante audio network.
3
HA device select buttons
Press one of these buttons to open the REMOTE HA SELECT...

Setup
 Reference Manual
235
Displaying the device statusYou can use the touch screen to verify the status of a connected CL series or R-series unit 
(except the Ro8-D) or the Dante status. In order to verify the status of an R-series unit from 
the console, it must be assigned to REMOTE HA in DANTE SETUP.CL seriesThe SETUP field of the DANTE SETUP window shows indicators for the status of the CL 
series console and the Dante network.
R-seriesThe I/O field of the I/O DEVICE screen shows indicators for...

Setup
 Reference Manual
236
Error messagesThe SYSTEM indicators will remain lit/blinking cyclically as follows until the problem has been 
resolved.
If service is necessary, please contact the Yamaha service center listed in the CL5/CL3/CL1 
Owner's Manual.
Warning messagesThe indicators will remain lit/blinking cyclically until the problem has been resolved.
If the green [SYNC] indicator is not lit, the device's word clock is not defined.
If the green indicator is blinking, the unit is...

Setup
 Reference Manual
237
Information messagesThe indicators will remain lit /blinking cyclically to report the status.
If the orange [SYNC] indicator is not lit, the unit is operating correctly.
If the green [SYNC] indicator is not lit, the device's word clock is not defined.
Using GPI (General Purpose Interface)The rear panel GPI (General Purpose Interface) connector can be used as an input/output 
connector. This connector provides five GPI IN ports and five GPI OUT ports. For example 
you can...

Setup
 Reference Manual
238
NOTE• With latched operation, the function will switch between active and inactive each time a trigger is 
input from the external switch. In this case, we recommend that you use a non-locking type of 
external switch.
• With unlatched operation, the function will be active only while the signal from the external switch 
is at the high level or low level. In this case, you may use either a non-locking or a locking type 
of external switch as appropriate for your needs.
•...

Setup
 Reference Manual
239
Using GPI OUTThe GPI OUT ports of the GPI OUT connector allow you to control an external device by 
performing operations on the CL series console.
MIDI/GPI screen (GPI page)1
GPI OUT status indicator
This indicates the status of the voltage that is being output from each GPI OUT port.
2
POLARITY MODE select button
This button selects the polarity of the GPI OUT port.
............... (Low active) Grounded when the GPI OUT port is active.
............... (High active) Open when...

Setup
 Reference Manual
240
3
GPI OUT SETUP button
The button shows the name of the currently-selected function or parameter. Press this 
button to display the GPI OUT SETUP window.
You can assign the following functions.
4
TEST button
While this is on, the corresponding GPI OUT port will be active and will output a control 
signal.
Using FADER STARTMake FADER START settings if you want a device connected to a GPI OUT port to operate 
in tandem with fader operations.
Function PARAMETER 1 PARAMETER 2...