Yamaha Cl 5 User Guide

							Setup
 Reference Manual
201
MONITORSOURCE SELECTSTEREO L/R
Recall the selected signal to the monitor. MONO (C)
LCR
PB OUT
OMNI1-2
OMNI3-4
OMNI5-6
OMNI7-8
DEFINE
SURROUND SOURCE 
SELECT*6)Recall the selected signal to the surround 
monitor.
SURROUND DOWN-
MIXSTEREO MONOWhen this function is off (the lamp is off), the 
setting returns to 5.1 monitor.
SURROUND SPEAKERSOLOWhen this function is on (the lamp is on), the 
SURROUND MONITOR screen opens. When this 
function is off (the lamp is off), the SURROUND 
MONITOR screen closes.
L, R, C, Ls, Rs, LFEThis functionality is the same as the SPEAKER 
MUTE function in the SURROUND MONITOR 
screen. When the SOLO button is on, it 
functions as a SOLO key.
MUTE 
MASTERMUTE GROUP 1
- Switch MUTE GROUP MASTER on/off. :
MUTE GROUP 8
ALL MUTE -Turns all MUTE GROUP MASTER settings on/off 
together.
NUENDO 
LIVETRANSPORTGO TO PROJECT START
Operate the transport functions of Nuendo Live. GO TO PREV MARKER
REWIND
FAST FORWARD
GO TO NEXT MARKER
NUENDO 
LIVETRANSPORTGO TO PROJECT END
Operate the transport functions of Nuendo Live. CYCLE
STOP
START
REC
EASY RECORDING
PEAK CLEAR -Clear the peak indicators of the Nuendo Live 
screen.
ADD MARKER -This function executes ADD MARKER of 
NUENDO Live.FUNCTION
PARAMETER 1
PARAMETER 2
Description
OSCILLATOROSCILLATOR ON - Switch the OSC on/off.
SELECTED CH ASSIGN -While holding down this key, press a SEL key of 
a channel to switch the assignment on/off. 
During this time, the [SEL] LED will be lit if 
assign is ON, or dark if OFF.
It goes OFF when the bank is switched.
DIRECT ASSIGN *1)Assign the oscillator to the channel selected 
from list 1).
PA G E  
CHANGEBOOKMARK -Memorize the currently-selected screen (hold 
down the key for two seconds or longer), or 
display the last-memorized screen (Hold down 
the key, then release it within two seconds). 
Popup windows can also be memorized. In the 
case of a rack, the number of that rack is also 
memorized.
BOOKMARK with “SEL” -Memorize the above BOOKMARK with the 
addition of the SEL status.
PREVIOUS PAGE
- Display the previous/next page.
NEXT PAGE
CLOSE POPUP - Close the displayed window. 
RECORDERTRANSPORTPLAY/PAUSE, STOP, 
FF/NEXT, 
REW/PREVIOUS, RECRecorder transport functions.
AUTO RECShortcut function for STOP  REC  PLAY.
Recording will be initiated in a single action. If 
this is executed during recording, the file being 
recorded will first be closed, and then recording 
will continue with a new file. 
REC & STARTStart recording immediately without entering 
record-ready mode.
DIRECT PLAYNO ASSIGN The specified audio file will be played once from 
the beginning.
Audio files to be played should be saved in the 
SONGS folder inside the YPE folder. Please note 
that a file cannot be specified if it is saved in the 
root directory or in any other folder. When you 
execute playback, the path in the TITLE LIST 
screen will move to \YPE\SONGS\. (TITLE 1)
:
SCENEINC RECALL - Recall the scene of the next existing number.
REC RECALL -Recall the scene of the previous existing 
number.
SCENEDIRECT RECALL SCENE #000-#300Directly recall the scene of the specified 
number.
RECALL UNDO - Execute RECALL UNDO.
STORE UNDO - Execute STORE UNDO.
INC - Select the scene of the next existing number.
DEC -
Select the scene of the previous existing number.
RECALL -
This function recalls the currently-selected scene.
STORE - Store the current settings.
SEND MODEMIX1-16/MIX17-24, 
MATRIX-If INPUT or ST IN is selected, switch the function 
of the Selected Channel section's send encoders 
from TO MIX1-16, TO MIX17-24, and MATRIX.
FUNCTION
PARAMETER 1
PARAMETER 2
Description 
						

							Setup
 Reference Manual
202
SENDS ON 
FADERMIX1-MIX24
NORMAL/WITH CUEThis function switches between the normal 
function on/off (NORMAL), and the function 
with cue on/off (WITH CUE). With the WITH 
CUE option, cue will be enabled if SENDS ON 
FADER mode is engaged or if you switch mode 
during SENDS ON FADER mode. Also, with the 
WITH CUE option, cue for all output channels 
will be canceled if SENDS ON FADER mode is 
disengaged. MTRX 1-MTRX 8
MIX ON FADER
MATRIX ON FADER
SENDS ON FADER
SET BY SEL+48V
-Hold down this key and press SEL to switch it 
on/off.
During this time, the [SEL] LED will be lit if on or 
dark if off.
If SET [PRE SEND] is selected, “SEND ON 
FADER” mode is engaged while you are holding 
down the [SEL] key.
It goes OFF when the bank is switched. Ø
INSERT ON
DIRECT OUT ON
PRE SEND
TO STEREO
TO MONO
TO LCR
GAIN COMPENSATION
SET DEFAULT 
VALUE--Press and hold this key, and then press any of 
the following knobs on the panel to reset that 
knob to its default value: a knob in the 
SELECTED CHANNEL section, a knob in the 
SELECTED CHANNEL VIEW screen, or a knob in 
the Centralogic section.
It goes OFF when the bank is switched.
SET NOMI-
NAL VALUE--While holding down this key, press a [SEL] key 
to set the fader of that channel to nominal level. 
You can also push a knob in the SEND field of 
the SELECTED CHANNEL VIEW screen to set the 
send level to nominal level.
It goes OFF when the bank is switched.
SURROUND 
PA NL ON
*5)In Surround mode, this is used to switch the bus 
assign on and off for the channel selected in list 
5). R ON
C ON
LFE ON
Ls ON
Rs ON
SURROUND 
PA NPANNING L
*5)In Surround mode, this is used to set hard 
panning for the channel selected in list 5). PANNING R
PANNING Front Center
PANNING Ls
PANNING Rs
PANNING Back
PANNING Side L
*5)In Surround mode, this is used to set hard 
panning for the channel selected in list 5). PANNING Side R
PANNING CenterFUNCTION
PARAMETER 1
PARAMETER 2
Description
SURROUND 
PA NPANNING TOGGLE *5)In Surround mode, this is used to toggle the 
settings for hard panning for the channel 
selected in list 5).
With each press, the setting is toggled in the 
following order: Center  L  Front Center  R 
 Side R  Rs  Back, Ls  Side L  (Center).
TALKBACKTALKBACK ONLATCH Switch TALKBACK on/off.
UNLATCHTurn TALKBACK on while pressed.
It goes OFF when the bank is switched.
SELECTED CH ASSIGN -While holding down this key, press a SEL key of 
an OUTPUT channel to switch the assignment 
on/off. During this time, the [SEL] LED will be lit 
if assign is ON, or dark if OFF.
The assignment setting made while holding 
down this key will be stored. Pressing the key 
again will recall the stored setting. Settings can 
be stored in multiple keys to facilitate rapid 
assignment switching.
It goes OFF when the bank is switched.
DIRECT ASSIGN *3)The operations performed when this key is 
pressed are as follows.
- Toggle assignment of channel selected in list 
3) ON and OFF.
At this time, the LED display is as shown below.
- If the channel is assigned, the LED will be on. 
Otherwise, the LED will be off.
TALKBACKDIRECT ASSIGN WITH 
ON*3)The operations performed when this key is 
pressed are as follows.
- Assignments other than for the channel 
selected in list 3) are removed.
- If a channel is assigned and TALKBACK is ON 
at the same time, TALKBACK is turned OFF 
and the channel assignment is removed.
- Otherwise, TALKBACK will be ON and the 
channel assignment will be ON.
At this time, the LED display is as shown below.
- If the channel is assigned and TALKBACK is ON 
at the same time, the LED will be on.
- Otherwise, the LED will be off.
TAP TEMPOCURRENT PAGE -Use the tap tempo function in the displayed 
screen.
EFFECT RACK1-8WITH POPUPUse the tap tempo function for the specified 
effect. If WITH POPUP is selected, the Tap 
Tempo screen is displayed. If WITHOUT POPUP 
is selected, the Tap Tempo screen is not 
displayed. WITHOUT POPUPFUNCTION
PARAMETER 1
PARAMETER 2
Description 
						

							Setup
 Reference Manual
203
*1) CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1L-ST IN 8R, MIX1-MIX24, MTRX1-MTRX8, ST L, ST 
R, MONO
*2) CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1-ST IN 8, MIX1-MIX24, MTRX1-MTRX8, STEREO, 
MONO(C)
*3) MIX1-MIX24, MTRX1-MTRX8, ST L, ST R, MONO
*4) CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1-ST IN 8, MIX1-MIX24, MTRX1-MTRX8, STEREO, 
MONO(C), DCA1-DCA16
*5) SELECTED CH, CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1L-ST IN 8R
*6) MIX1-6, EXT5.1 1, EXT5.1 2, EXT5.1 3, EXT ST 1, EXT ST 2, EXT ST 3, EXT ST 4, MIX1/2, MIX3/4, MIX5/6, 
MIX7/8, MIX9/10, MIX11/12, MIX13/14, MIX15/16, MIX17/18, MIX19/20, MIX21/22, MIX23/24, MATRIX1/2, 
MATRIX3/4, MATRIX5/6, MATRIX7/8, STEREO, MONO, PB OUT
USER DEFINED knobsThis section explains how to assign the desired functions to the USER DEFINED knobs in the 
USER DEFINED KNOBS section on the top panel, and press these knobs to execute the 
defined function.
If you are logged-in as a user, you can make USER DEFINED knob settings for the user. If 
you are logged-in as the Administrator, you can also make the USER DEFINED knob settings 
for the Guest account.
NOTE
For details on the assignable functions and their parameters, refer to “Functions that can be 
assigned to USER DEFINED knobs” (page 204).
USER 
DEFINED 
KEYSBANK SELECTBANK AWhen selected, the lamp for the corresponding 
key comes on.
BANK BWhen selected, the lamp for the corresponding 
key comes on.
BANK CWhen selected, the lamp for the corresponding 
key comes on.
BANK DWhen selected, the lamp for the corresponding 
key comes on.
PREVIOUS BANKSwitches to the previous bank. If the current 
bank is BANK A, it switches to BANK D.
NEXT BANKSwitches to the next bank. If the current bank is 
BANK D, it switches to BANK A.FUNCTION
PARAMETER 1
PARAMETER 2
Description
STEP
1.In the Function Access Area, press the SETUP button.
2.In the SETUP screen, press the USER SETUP button.
3.In the USER SETUP window, press the USER DEFINED KNOBS tab.
4.Press the button corresponding to the USER DEFINED knob to which you want to 
assign a function.
5.In the USER DEFINED KNOB SETUP window, make sure that the FUNCTION field is 
enclosed by a frame, then select the function that you want to assign.
6.If the selected function has parameters, press the PARAMETER 1 or 2 field to move 
the frame, then select parameters 1 and 2 in the same way.
7.Press the OK button to close the USER DEFINED KNOB SETUP window.
8.To execute an assigned function, press the corresponding USER DEFINED [1]-[4] 
knob on the panel.
USER SETUP screen
(USER DEFINED KNOBS page)USER DEFINED KNOB SETUP window 
						

							Setup
 Reference Manual
204
NOTE• If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access 
the USER DEFINED KNOBS and ASSIGNABLE ENCODER for Guest page and make USER 
DEFINED knob settings for the Guest account.
• The 4 knobs in the USER DEFINED KNOBS and ASSIGNABLE ENCODER page correspond to 
USER DEFINED knobs [1]-[4] on the top panel. The name of the function or parameter assigned 
to each knob appears to the right of the corresponding button. If nothing is assigned to the button, 
an indication of “---” is shown.• The list shown in the USER DEFINED KNOB SETUP window is the same for all models of the CL 
series.
For the CL3/CL1, the display will indicate “Cannot Assign!” you specify a parameter that does not 
exist on that model.
• If there are no parameters for the registered USER DEFINED knob, nothing will occur when the 
knob is operated.
About TOUCH AND TURNThe TOUCH AND TURN function is assigned to the USER DEFINED [4] 
knob by default. If this function is assigned to one of the USER DEFINED 
knobs, you can press a desired knob in the touch screen and then 
immediately use the USER DEFINED knob to operate it.
At this time, a pink frame is shown around the knob in the touch screen, 
indicating that you can operate that knob.
Functions that can be assigned to USER DEFINED 
knobs
Function
PARAMETER 1
PARAMETER 2
NO ASSIGN - -
AUTOMIXER WEIGHT *1)
BRIGHTNESSLAMP -
PA N E L -
SCREEN -
CH COLOR -
NAME -
CUEINPUT PFL TRIM -
DCA TRIM -
OUTPUT PFL TRIM -
CUE LEVEL -
DIRECT OUT LEVEL LEVEL *14)
DYNAMICS1THRESHOLD *2)
RANGE *4)
RATIO
*2)
ATTAC K
HOLD
*4)
DECAY
RELEASE
*2) OUTGAIN
KNEE
WIDTH *13)
DYNAMICS2THRESHOLD
*4) RATIO
FREQUENCY
ATTAC K
RELEASE
OUTGAIN
KNEE
WIDTH
EFFECTDisplays the EFFECT RACK No. (1-8) for 
the target operation as well as the 
name of the mounted EFFECT TYPE or 
the name of the GEQ/PEQ TYPE *a).Displays the names of the 32 parame-
ters for the EFFECT TYPE *b). Displays
“----” if a GEQ/PEQ is mounted. 
						

							Setup
 Reference Manual
205
*1) SELECTED CH, Automixer ch1-16
*2) SELECTED CH, CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1-ST IN 8, MIX1-MIX24, MTRX1-
MTRX8, STEREO, MONO (C)
*3) SELECTED CH, CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1L-ST IN 8R
*4) SELECTED CH, CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1-ST IN 8
*5) SELECTED CH, CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1L-ST IN 8R, MIX1-MIX24
*6) MIX1-MIX24, MTRX1-MTRX8, ST L, ST R, MONO
*7) SELECTED CH, CL5:  CH1-CH72, CL3:  CH1-CH64, CL1:  CH1-CH48, ST IN 1L-ST IN 8R, MIX1-MIX24, ST L, ST 
R, MONO
*10) # 1-# 6
*11) REMOTE HA #1-#8
*12) DANTE 1-DANTE64, OMNI 1-OMNI 8, SLOT1 1-SLOT1 16, SLOT2 1-SLOT2 16, SLOT3 1-SLOT3 16, DIGITAL 
OUT L, DIGITAL OUT R
*13) SELECTED CH, MIX1-MIX24, MTRX1-MTRX8, STEREO, MONO (C)
*14) SELECTED CH, CL5: CH1-CH72, CL3:  CH1-CH64, CL1: CH1-CH48
*a) If not mounted in the RACK, “----” is displayed.
*b) If there are no parameters, “----” is displayed. EQAT T
*2) LOW Q
LOW FREQUENCY
LOW GAIN
LOW MID Q
LOW MID FREQUENCY
LOW MID GAIN
HIGH MID Q
HIGH MID FREQUENCY
HIGH MID GAIN
HIGH Q
HIGH FREQUENCY
HIGH GAIN
EXTERNAL HA GAIN1-GAIN8 *10)
HPF FREQUENCY *4)
I/O DEVICE GAIN1-GAIN32 *11)
INPUT DELAY DELAY TIME *3)
INPUT GAINANALOG GAIN
*4)
DIGITAL GAIN
MIDI CONTROL CHANGECTRL 1-CTRL 31 -
CTRL 33-CTRL 95 -
CTRL 102-CTRL 119 -
MONITORDIMMER LEVEL -
TALKBACK DIMMER LEVEL -
MONITOR DELAY -
MONITOR FADER -
OSCILLATORLEVEL -
FREQUENCY -
LEVEL(EVEN) -
FREQUENCY(EVEN) -
HPF -
LPF -
WIDTH -
INTERVAL -
OUTPUT LEVEL LEVEL *6)
OUTPUT PORTDELAY TIME
*12)
GAIN
PREMIUM RACKDisplays the PREMIUM RACK No. (1A-
8B) for the corresponding operation, as 
well as the name of the mounted PRO-
CESSOR *a).Displays the names of the 64 parame-
ters for the PROCESSOR *b).
Function
PARAMETER 1
PARAMETER 2
RECORDERINPUT GAIN -
OUTPUT GAIN -
SCENE SELECT -
TO MIX LEVEL MIX1-MIX24 *3)
TO MATRIX LEVEL MATRIX1-MATRIX8 *7)
TO MIX PAN MIX1/2-MIX15/16 *3)
TO MATRIX PAN MATRIX1/2-MATRIX7/8 *7)
TO ST/MONOPA N / B A L
*5)
CSR
TOUCH AND TURN - -
Function
PARAMETER 1
PARAMETER 2 
						

							Setup
 Reference Manual
206
Assignable encodersYou can assign the desired function to the GAIN/PAN/ASSIGN knob on the fader strip of each 
channel, and control the function using the knob. For details on the assignable functions and 
their parameters, refer to “Functions that can be assigned to the assignable encoders” 
(page 207).
NOTE
• If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access 
the USER DEFINED KNOBS and ASSIGNABLE ENCODER for Guest page and make 
assignable knob settings for the Guest account.
• SELECTED SEND is the default setting. If SELECTED SEND is selected, you can use the 
assignable encoders to adjust the send level to the MIX/MATRIX channel that is selected for 
SENDS ON FADER in the Function Access Area.• The CL3 and CL1 have only one [GAIN/PAN/ASSIGN] key, so the function 
of all GAIN/PAN/ASSIGN knobs will change simultaneously. On the CL5, 
you can switch the knob function in block A (left side) and block C/Master 
fader section (right side) independently by using the corresponding [GAIN/
PAN/ASSIGN] keys.
• This assignment does not apply to the multifunction knobs in the 
Centralogic section, since these knobs are used to control on-screen 
parameters.
STEP
1.In the Function Access Area, press the SETUP button.
2.In the SETUP screen, press the USER SETUP button.
3.In the USER SETUP window, press the USER DEFINED KNOBS tab.
4.Press the button in the ASSIGNABLE ENCODER field on the USER DEFINED KNOB 
page.
5.In the ASSIGNABLE ENCODER SETUP window, select the function you want to 
assign.
6.Press the OK button to close the ASSIGNABLE ENCODER SETUP window.
7.Press the [GAIN/PAN/ASSIGN] key on the top panel repeatedly to select ASSIGN.
8.Operate the GAIN/PAN/ASSIGN knob on each channel strip.
USER SETUP screen
(USER DEFINED KNOBS and 
ASSIGNABLE ENCODER page)ASSIGNABLE ENCODER 
SETUP window 
						

							Setup
 Reference Manual
207
Functions that can be assigned to the assignable 
encoders
*1 Preference setting and the state of the ALTERNATE function will determine whether this will be analog gain or 
digital gain.
*2 The send destination that is the target of Sends On Fader will be selected.
*3 The state of the ALTERNATE function will determine whether turning the encoder will switch the PRE/POST 
setting of the corresponding send or will switch the corresponding send on/off when pressed.
*4 The state of the ALT function will determine whether pressing the encoder will switch the high-pass filter on/off.
*5 The state of the ALTERNATE function will determine whether pressing the encoder will switch DYNAMICS 1 on/off.
*6 The state of the ALTERNATE function will determine whether pressing the encoder will switch DYNAMICS 2 on/off.
*7 The state of the ALTERNATE function will determine whether turning the encoder will switch to F/R.
*8 The state of the ALTERNATE function will determine whether turning the encoder will switch to L/R.
PAN
GAIN
ASSIGN
Function
PARAMETER 1
PARAMETER 2
O PAN/BALANCEPA N
BAL
O ANALOG GAIN A.GAIN *1
O DIGITAL GAIN D.GAIN *1
ONO ASSIGN(Nothing will be 
displayed.)
O SELECTED SENDMIX1-MTRX8
Depends on 
status
*2
OMIX1 SEND MIX1 *3
OMIX2 SEND MIX2 *3
OMIX3 SEND MIX3 *3
OMIX4 SEND MIX4 *3
OMIX5 SEND MIX5 *3
OMIX6 SEND MIX6 *3
OMIX7 SEND MIX7 *3
OMIX8 SEND MIX8 *3
OMIX9 SEND MIX9 *3
O MIX10 SEND MIX10 *3
O MIX11 SEND MIX11 *3
O MIX12 SEND MIX12 *3
O MIX13 SEND MIX13 *3
O MIX14 SEND MIX14 *3
O MIX15 SEND MIX15 *3
O MIX16 SEND MIX16 *3
O MIX17 SEND MIX17 *3
O MIX18 SEND MIX18 *3
O MIX19 SEND MIX19 *3
O MIX20 SEND MIX20 *3
O MIX21 SEND MIX21 *3
O MIX22 SEND MIX22 *3
O MIX23 SEND MIX23 *3
O MIX24 SEND MIX24 *3
O MATRIX1 SEND MTRX1 *3
O MATRIX2 SEND MTRX2 *3
O MATRIX3 SEND MTRX3 *3
O MATRIX4 SEND MTRX4 *3
O MATRIX5 SEND MTRX5 *3
O MATRIX6 SEND MTRX6 *3
O MATRIX7 SEND MTRX7 *3
OMATRIX8 SEND MTRX8 *3
O HPF FREQUENCY HPF *4
O DYNAMICS1 THRESHOLD THRE1 *5
O DYNAMICS2 THRESHOLD THRE2 *6
O DIGITAL GAIN D.GAIN
OEQ ATT ATT
OINPUT DELAY DELAYUnits of scale 
are m, ms, ft, 
and fr. No 
description for 
samples.
O DIRECT OUT LEVEL D.OUT
OSURROUND L-R PAN L/R *7
OSURROUND F-R PAN F/R *8
O SURROUND ROUND PAN L/R and F/R
OSURROUND DIV DIV
O SURROUND LFE LFE
PA N
GAIN
ASSIGN
Function
PARAMETER 1
PARAMETER 2 
						

							Setup
 Reference Manual
208
GAIN/PAN/ASSIGN knob (assignable encoder) 
functionsIn CL V1.7 and later, the following functions have been added to SENDS ON FADER mode.When using the [GAIN/PAN/ASSIGN] keys on the top panel to select 
ASSIGNUse assignable encoders to adjust the level of channels.
Channel name display indicationWhen using the [GAIN/PAN/ASSIGN] keys on the top panel to select 
PA NUse assignable encoders to adjust PAN sent from channels to the MIX/MATRIX bus (bus set 
for Stereo send in the BUS SETUP screen).
Channel name display indication
Custom fader bankGroups that organize channels routed to the top-panel faders are called “fader banks.” 
There are input and output channel banks, as well as custom fader banks. Custom fader 
banks enable you to select various combinations of channels, regardless of channel types. 
This section explains how to set up a custom fader bank.
NOTE
• If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access 
the CUSTOM FADER BANK/MASTER FADER for Guest page, and make custom fader bank 
settings for the Guest account.
• You can also press the fader assign select buttons to assign channels to faders.
Channel levels 
Adjust with assignable encoder.
Send level to MIX/MATRIX bus
Adjust with the fader on the top panel.PAN sent from channel to MIX/MATRIX bus
Adjust with assignable encoder.
Send level to MIX/MATRIX bus
Adjust with the fader on the top panel.
STEP
1.In the Function Access Area, press the SETUP button.
2.In the SETUP screen, press the USER SETUP button.
3.In the USER SETUP window, press the CUSTOM FADER tab.
4.Use the Bank Select keys to recall the fader settings to the top panel for the channels 
you want to add to the custom fader bank.
5.In the CUSTOM FADER BANK/MASTER FADER page, press the bank select button for 
the custom fader bank you want to set up.
6.In the FADER field, press the select button for the fader you want to set up.
7.Press a [SEL] key on the top panel to assign a channel to the fader number selected 
in step 6.
8.To assign channels to other faders, repeat steps 5 through 7.
USER SETUP window (CUSTOM 
FADER BANK/MASTER FADER page) 
						

							Setup
 Reference Manual
209
USER SETUP screen
(CUSTOM FADER BANK/MASTER FADER page)CUSTOM FADER BANK/MASTER FADER field
1
Bank select buttons
Enable you to select a custom fader bank to which you want to assign a group of 
channels.
The number and name of the custom fader banks vary depending on the console 
model.
CL5: A1, A2, B1, C1, C2, C3, C4, C5, C6
CL3: A1, A2, A3, B1, B2
CL1: A1, B1, B2, B3, B4
2
MASTER button
Press this button to set channels that will be controlled by the faders in the Master fader 
section.
3
Block indicators
Display the graphics of the top panel block and faders that are the current target for 
editing.
The graphics vary depending on the console model.
CL5: A (16 faders), B, C, MASTER
CL3: A (16 faders), B, MASTER
CL1: A (8 faders), B, MASTER
FADER field
4
Fader select button
Selects the target fader. Press this button to select it, then press [SEL] keys on the top 
panel to add the corresponding channels to the selected fader bank.
5
Fader assign select button
Opens the Fader assign select window, in which you can change the channel assigned 
to the fader.
6
CLEAR ALL button
Clears all the current fader bank assignment. Pressing this button will open a 
confirmation dialog box. Press OK to clear the assignment. Otherwise, press CANCEL to 
return to the previous screen without changing the setting.
Master faderYou can set the channels that will be controlled by the two faders in the Master fader section.
NOTE
If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access 
the CUSTOM FADER BANK/MASTER FADER for Guest page, and make master fader settings 
for the Guest account.
126
435
STEP
1.In the Function Access Area, press the SETUP button.
2.In the SETUP screen, press the USER SETUP button.
3.In the USER SETUP window, press the CUSTOM FADER tab.
4.In the CUSTOM FADER BANK/MASTER FADER page, press the MASTER button.
5.In the FADER field, press the number button for the fader you want to set up.
6.Press a [SEL] key on the top panel to assign a channel to the fader number selected 
in step 5.
USER SETUP window (CUSTOM 
FADER BANK/MASTER FADER page) 
						

							Setup
 Reference Manual
210
Custom fader bank functionsCustom fader bank settings can be stored/recalled for individual scenes.
Custom fader bank settings are stored in scene data in separate regions for each model.
NOTE
Custom fader bank settings differ between models, and are not compatible. For example, custom 
fader bank settings included in scenes stored in CL5 cannot be reproduced if that same scene is 
recalled in CL3 or CL1. You must create and store custom fader bank settings in CL3 and CL1.
Precautions for when Loading Console DataIn V2.0 and later, custom fader bank settings are not only included in user settings, but in 
scene data as well. The custom fader bank settings that are called up vary depending on the 
logged-in user, the type of the loaded data, and the version. Please note the following points:
• If you load console data of the ALL type as Administrator, the custom fader bank settings 
for the saved Administrator are called up.
If you load ALL data as Guest or another user, the custom fader bank settings for the saved 
current scene are called up.
• If you load ALL data that was saved in CL V1.70 or earlier, since scenes do not include 
custom fader bank settings, the custom fader bank settings for the current scene when the 
load was performed are applied to all scenes. Therefore, before loading ALL data, we 
recommend that you either change users to set the custom fader bank to the desired 
setting, or that you enable Recall Safe for the custom fader bank.
Console LockYou can temporarily prohibit console operations in order to prevent unwanted operation. This 
setting disables operations of the panel, so that controllers cannot be operated by an 
accidental touch or by an unauthorized third party while the operator is taking a break.
If a password is set for the currently logged-in user, that password will be used for the Console 
Lock function. When the Console Lock function is enabled, the CONSOLE LOCK screen will 
appear and all controllers (excluding the MONITOR LEVEL knob) will become inoperable.
NOTE
• If you have forgotten the password, refer to “Initializing the unit to factory default settings” 
(page 245).
• The Guest cannot set a password.
• Even while the console is locked, control from an external device via MIDI or CL Editor will still 
operate as usual.
Locking the console
CL5
CL5 console
Recall Store Recall Store Recall Store
CL3
CL1
CL3 console
CL1 console
Custom fader bank settings
STEP
1.In the Function Access Area, press the SETUP button.
2.In the SETUP screen, press the CONSOLE LOCK button.
3.If you are logged-in as a user for whom a password is set, enter the password for the 
user.
4.Press the OK button to enable Console Lock function.