Yamaha Cl 5 User Guide

Meters
 Reference Manual
121
SHOW SEND LEVEL buttonIf you switch to SENDS ON FADER mode when this button is on, the color and 
position of the faders in the INPUT METER screen show the type of send 
destination bus, the send level to that bus, and ON/OFF status.For INPUT METERFader color
The channel color is the same as the currently selected MIX/MATRIX bus (SEND MASTER).
The position of the fader is the level of the signal sent to the bus.
The fader turns gray if you switch the SEND button to OFF or...

Meters
 Reference Manual
122
5
CUE OVERRIDE button
If this button is switched on, the cue signal set in the CUE screen is sent to the real time 
analyzer, and an analysis is displayed.
• If CUE MODE is set to MIX CUE, the frequency analysis is performed on a signal that is 
a mix of all channels selected in the CUE screen.
• If CUE MODE is set to 5.1 SOLO, the signal is treated as LAST CUE. In other words, the 
frequency analysis is performed on the POST ON signal of the input channel.
6
BALLISTICS...

Meters
 Reference Manual
123
Function Access Area screenIf you set a bus to Surround mode in BUS SETUP, the METER screen in the Function Access 
Area appears as shown below.
The display specifications are as follows.
• The meter for the SURROUND signal is shown on the left side, and the meter for the 
STEREO signal is shown on the right side. The layout for L R C LFE Ls and Rs is the 
same as the layout set in the SURROUND SETUP screen.
When cue is operating
• EFFECT CUE is shown on the right side, as...

Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
 Reference Manual
124
Graphic EQ, Parametric EQ, Effects, and 
PREMIUM RACKThis chapter explains how to use the built-in graphic EQ, parametric EQ, effects, and Premium 
Rack.About the virtual rackCL series consoles enable you to use the built-in graphic EQ (subsequently abbreviated as 
“GEQ” ), parametric EQ (subsequently abbreviated as “PEQ” ), and effects/processors to 
modify signals. You can use two types of GEQ: 31BandGEQ which enables you to...

Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
 Reference Manual
125
Virtual rack operationsThis section explains how to mount a GEQ, PEQ, or effect in the virtual rack, and patch the 
input and output of the rack as an example.
NOTE
• In steps 6 and 8, you can make settings such that the confirmation dialog box will not appear 
(page 196).
• The type of GEQ, PEQ, or effect mounted in each rack, its parameter settings, and the input-
source and output-destination settings are saved as part of the...

Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
 Reference Manual
126
4
INPUT PATCH button
If the type is EFFECT, two buttons (L/R) will appear. If the type is Flex15GEQ or 
8BandPEQ, two buttons (A/B) will appear. If the type is 31BandGEQ, one button will 
appear.
Press this button to open the CH SELECT window, in which you can select the path of 
the signal patched to the rack input.
The categories and channels that can be selected are shown below.
•OUT CH.................................... MIX...

Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
 Reference Manual
127
6
Rack container
Indicates the contents of the rack. This container varies depending on the rack type you 
selected in the RACK MOUNTER window.
• If nothing is mounted:
Press this area to open the RACK MOUNTER window, in which you can select the GEQ 
or effect that will be mounted in the rack.
• If 31BandGEQ is mounted:
This area indicates the settings for each band, GEQ on/off status, and input/output level. 
Press this area to...

Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
 Reference Manual
128
7
Link indicator
Indicates that an odd-numbered rack and even-numbered rack of the 31BandGEQ, A 
and B of the Flex15GEQ, or A and B of the 8BandPEQ are linked to each other.
RACK MOUNTER windowMount a GEQ, PEQ, or effect in the rack. This window will appear if you press the rack mount 
button in the VIRTUAL RACK window.1
Rack number
Indicates the number for the selected rack.
2
Virtual rack
This area indicates the GEQ or effect...

Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
 Reference Manual
129
Inserting a GEQ in a channelThis section explains how to insert a GEQ into the selected channel for use.
NOTE
• If you are using a stereo source, you can mount a Flex15GEQ, or mount two 31BandGEQ units 
in adjacent odd-numbered/even-numbered racks. This will let you link the two GEQ units in a later 
step.
• You can view the input and output levels of the GEQ in the rack in the GEQ field.
• For details on GEQ operations, refer to...

Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
 Reference Manual
130
For GEQ EDIT window (31BandGEQ, Flex15GEQ)1
RTA button
Turn this button on to overlay a frequency response graph on the EQ.
2
HOLD button
Press this button to hold the peak of the graph that displays RTA.
Using the 31BandGEQYou will use the Centralogic section's faders 1-8 and [ON] keys to control the 31BandGEQ.
NOTE
• When a fader of the Centralogic section is in the center (flat) position, the corresponding [ON] key 
will go...