Yamaha Cl 5 User Guide

Monitor and Cue functions
 Reference Manual
111
NOTE• The cue signal is sent to the monitor output and PHONES Out jacks regardless of whether the 
CUE OUTPUT button is on or off. However, the cue signal will no longer be sent to monitor output 
if CUE INTERRUPTION is turned off. The cue signal is always sent to the PHONES Out jack, 
regardless of the CUE INTERRUPTION setting.
• When using the MIX/MATRIX bus select buttons in the SENDS ON FADER window, you can 
press the selected button once again to turn...

Monitor and Cue functions
 Reference Manual
112
CUE windowYou can make detailed settings for the cue. This window will appear when you press the 
INPUT/DCA/OUTPUT CUE field.1
CUE MODE buttons
Select one of the following two cue modes:
• MIX CUE
All selected channels will be mixed and monitored.
•LAST CUE
Only most recently selected channel will be monitored.
NOTEAll cue selections will be cleared if you switch between MIX CUE mode and LAST CUE mode in 
the CUE MODE section.
INPUT CUE fieldThis field...

Monitor and Cue functions
 Reference Manual
113
D
CUE OUT PATCH button
Press this button to open the PORT SELECT window, in which you can select an output 
port to patch to the cue out L/R channels.
FADER CUE RELEASE fieldMove the fader of the channel that is cued to set the FADER CUE RELEASE function for 
releasing the cue.E
ON button
Switches the FADER CUE RELEASE function on or off.
F
THRESHOLD knob
Sets the fader value for releasing the cue. If the fader value exceeds the value set with 
this knob,...

Talkback and Oscillator
 Reference Manual
114
Talkback and OscillatorTalkback is a function that sends the signal of a mic connected to the TALKBACK jack to the 
desired bus. This is used mainly to convey instructions from the operator or sound engineer 
to the performers and staff. If necessary, you can also use a mic connected to an INPUT jack 
on the I/O device or the OMNI IN jack on the CL unit for talkback.
CL series consoles also feature an oscillator that can output a sine wave or pink noise to...

Talkback and Oscillator
 Reference Manual
115
MONITOR screenIn the MONITOR screen, the TALKBACK field enables you to check the current talkback 
settings, and turn talkback on or off.1
TALKBACK display buttons
When you press this button, the TALKBACK screen will appear, in which you can make 
detailed talkback settings.
2
TALKBACK IN field
• +48V indicator ........................ Indicates the on/off status of the +48V phantom power 
supplied to the TALKBACK jack.
•Input level meter......................

Talkback and Oscillator
 Reference Manual
116
4
+48V button
This is an on/off switch for the phantom power (+48V) supplied to the selected input 
port.
NOTEThis button will not appear if no input port is selected.
5
ANALOG GAIN knob
Indicates the analog gain value for the selected input port. Press this knob to control the 
level using the multifunction knobs.
6
Level meter
Indicates the input level of a mic connected to the selected input port.
7
GC button
Turns the Gain Compensation (gain correction...

Talkback and Oscillator
 Reference Manual
117
2
OSCILLATOR LEVEL field
Indicates the frequency and level of the currently-selected oscillator. A meter in this field 
indicates the output level of the oscillator. Press the LEVEL knob to adjust the oscillator 
level using the multifunction knob.
3
OSCILLATOR MODE field
Indicates the currently-selected oscillator mode. Pressing the MODE button repeatedly 
will switch modes.
4
OSCILLATOR ASSIGN field
An indicator lights to indicate the currently-selected...

Talkback and Oscillator
 Reference Manual
118
Mode = PINK NOISE
•LEVEL knob..........Indicates the output level of the pink noise. You can adjust the 
value by using the multifunction knob.
•HPF knob..............Indicates the cutoff frequency of the HPF that processes pink 
noise. You can adjust the value by using the multifunction knob. 
Use the button below the knob to switch the HPF on or off.
•LPF knob...............Indicates the cutoff frequency of the LPF that processes pink 
noise. You can adjust...

Meters
 Reference Manual
119
MetersThis chapter explains the METER screen that shows the input and output level meters for all 
channels, and operations related to the optional MBCL meter bridge.Operations in the METER screenBy accessing the METER screen, you can view the input and output levels of all channels on 
the screen, and switch the level meter's metering points (the points in the signal route at which 
the level is detected). To access the METER screen, press the METER field of the Function...

Meters
 Reference Manual
120
Fader level and meter displayThis area displays the meter and fader for each channel.1
Channel number
Indicates the channel number.
2
Σ clipping indicator
Lights to indicate that a signal is clipping at some point in the channel.
3
OVER indicator
Lights if the signal is clipping at the input section of the channel.
4
Meters
Indicates the input or output level of the channel.
5
Faders
The channel level is indicated by the fader position and by a numeric value (in dB) that...