Xerox WorkCentre 3045 Service Manual
Here you can view all the pages of manual Xerox WorkCentre 3045 Service Manual. The Xerox manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 151
Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 2-97Error Troubleshooting Waiting for Continue Key to be Pressed After Reloading Paper The printer is in manual duplex mode waiting for user interaction. Applicable Error • 075-921: Waiting for Continue key to be pressed after reloading paper. Initial Actions • Remove the paper from the Output Tray, put it back in to the paper tray, and press OK. • Cycle printer power. • If the problem persists, use the following procedure. Tro u b l e s h...
Page 152
2-98 Xerox Internal Use Only Phaser 3010/3040/WorkCentre 3045 Service Error Troubleshooting Reg On Early Jam Paper stuck in the Registration section, Main or Bypass Tray. Applicable Error • 077-100: Reg On Early Jam Initial Actions • Check the media path for obstructions or debris. • Cycle printer power. • If the problem persists, use the following procedure. Tro u b l e s h o ot i n g Re fe re n c e Ta b l e Applicable Parts Wiring and Plug/Jack Map References ■Registration Sensor, PL2.3.10 ■MCU...
Page 153
Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 2-99Error Troubleshooting Reg Off Jam The paper does not pass through the Registration Sensor within the specified time. Applicable Error • 077-104: Reg Off Jam Initial Actions • Check the media path for obstructions or debris. • Cycle printer power. • If the problem persists, use the following procedure. Tro u b l e s h o ot i n g Re fe re n c e Ta b l e Applicable Parts Wiring and Plug/Jack Map References ■Registration Sensor, PL2.3.10...
Page 154
2-100 Xerox Internal Use Only Phaser 3010/3040/WorkCentre 3045 Service Error Troubleshooting Exit On Jam The paper does not reach the Exit Sensor within the specified time. Applicable Error • 077-106: Exit On Jam Initial Actions • Check the media path for obstructions or debris. • Cycle printer power. • If the problem persists, use the following procedure. Tro u b l e s h o ot i n g Re fe re n c e Ta b l e Applicable Parts Wiring and Plug/Jack Map References ■Registration Sensor, PL2.3.10 ■Main...
Page 155
Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 2-101Error Troubleshooting Exit Off Early Jam The paper passed through the Exit Sensor earlier than the specified time, or did not pass through the Exit Sensor within the specified time. Wa rn i n g Allow the Fuser to cool before servicing the printer. Applicable Errors • 077-108: Exit Off Early Jam • 077-109: Exit Off Jam Initial Actions • Check the media path for obstructions or debris. • Cycle printer power. • If the problem persists,...
Page 156
2-102 Xerox Internal Use Only Phaser 3010/3040/WorkCentre 3045 Service Error Troubleshooting Rear Door Open A Rear Cover Open error was detected. Applicable Error • 077-304: Rear Cover Open Initial Actions • Open and close the Rear Door. • Cycle printer power. • If the problem persists, use the following procedure. Tro u b l e s h o ot i n g Re fe re n c e Ta b l e Applicable Parts Wiring and Plug/Jack Map References ■Rear Door, PL1.0.8 ■Interlock Switch, PL7.2.1 ■LVPS, PL7.2.11 ■MCU Board, PL7.1.3...
Page 157
Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 2-103Error Troubleshooting Exit Jam Paper remaining at the Exit section of the Printer was detected. Wa rn i n g Allow the Fuser to cool before servicing the printer. Applicable Error • 077-900: Exit Jam Initial Actions • Check the media path for obstructions or debris. • Cycle printer power. • If the problem persists, use the following procedure. Tro u b l e s h o ot i n g Re fe re n c e Ta b l e Applicable Parts Wiring and Plug/Jack Map...
Page 158
2-104 Xerox Internal Use Only Phaser 3010/3040/WorkCentre 3045 Service Error Troubleshooting Remain Registration Jam Paper remaining at the registration section of the printer was detected. Applicable Error • 077-901: Remain Registration Jam Initial Actions • Check the media path for obstructions or debris. • Cycle printer power. • If the problem persists, use the following procedure. Tro u b l e s h o ot i n g Re fe re n c e Ta b l e Applicable Parts Wiring and Plug/Jack Map References...
Page 159
Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 2-105Error Troubleshooting XERO Near Life The xerographics assembly is approaching end of life. Applicable Error • 091-402: XERO Near Life Initial Actions • Cycle printer power. • If the problem persists, use the following procedure. Tro u b l e s h o ot i n g Re fe re n c e Ta b l e Applicable Parts Wiring and Plug/Jack Map References ■MCU Board, PL7.1.3■“Xerographics” on page 7-15 Troubleshooting Procedure Table Step Actions and...
Page 160
2-106 Xerox Internal Use Only Phaser 3010/3040/WorkCentre 3045 Service Error Troubleshooting ADC Sensor Error An ADC Sensor error is detected. Applicable Error • 092-651: ADC Sensor Error Initial Actions • Cycle printer power. • If the problem persists, use the following procedure. Tro u b l e s h o ot i n g Re fe re n c e Ta b l e Applicable Parts Wiring and Plug/Jack Map References ■MCU Board, PL7.1.3■“Xerographics” on page 15 Troubleshooting Procedure Table Step Actions and Questions Yes No...