Xerox DocuPrint 255DN User Manual
Have a look at the manual Xerox DocuPrint 255DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 228 Xerox manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Serial Menu Chapter 1: Configuring the Printer v1-55 Serial PDL Set the default emulation for the serial port. The available values are: Auto* PCL Postscript 1. Press Menu Up or Menu Down until you see:Menus Serial Menu 2. Press Item Up or Item Down until you see:Serial Menu Serial PDL 3. Press Va l u e U p or Va l u e D o w n until you see:Serial PDL = New Value 4. Press Enter. You will see:Serial Menu Serial PDL 5. Press Online. You will see:Ready Flow Control Set the handshaking parameters for the serial port. The available values are: XON/XOFF Robust XON/XOFF Hardware* 1. Press Menu Up or Menu Down until you see:Menus Serial Menu 2. Press Item Up or Item Down until you see:Serial Menu Flow Control 3. Press Va l u e U p or Va l u e D o w n until you see:Flow Control = New Value 4. Press Enter. You will see:Serial Menu Flow Control 5. Press Online. You will see:Ready Binary PS Enable or disable the binary mode of PostScript. The available values are: On Off* 1. Press Menu Up or Menu Down until you see:Menus Parallel Menu 2. Press Item Up or Item Down until you see:Parallel Menu Binary PS 3. Press Va l u e U p or Va l u e D o w n until you see:Binary PS = New Value 4. Press Enter. You will see:Parallel Menu Binary PS 5. Press Online. You will see:Ready Table 1.14 Serial Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.14 Page2 of 3 Downloaded From ManualsPrinter.com Manuals
Serial Menu 1-56 vDocuPrint NC60 System Administrator Guide Baud Rate Set the baud rate for the serial port. The available values are: 38400 28800 19200 9600* 4800 2400 1200 600 1. Press Menu Up or Menu Down until you see:Menus Serial Menu 2. Press Item Up or Item Down until you see:Serial Menu Baud Rate 3. Press Va l u e U p or Va l u e D o w n until you see:Baud Rate = New Value 4. Press Enter. You will see:Serial Menu Baud Rate 5. Press Online. You will see:Ready Table 1.14 Serial Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.14 Page3 of 3 Downloaded From ManualsPrinter.com Manuals
Ethernet Menu Chapter 1: Configuring the Printer v1-57 Ethernet Menu Use the Ethernet Menu to set options for the Ethernet port. The menu hierarchy is shown in Figure 1.11 on page 1-58. Refer to Table 1.15 on page 1-59 for step-by-step instructions. Downloaded From ManualsPrinter.com Manuals
Ethernet Menu 1-58 vDocuPrint NC60 System Administrator Guide Figure 1.11 Ethernet Menu hierarchy LPR EnableOn* Off LPR PDL Job Menu Password Menu Tr a y M e n u PCL Menu System Menu Color Adjust Menu Imaging Menu Parallel Menu Serial Menu Ethernet Menu Token Ring Menu Novell Menu Print Menu Media Server Menu Service Menu Reset Menu DLC/LLC EnableLPR Banner DLC/LLC PDL LPR Binary PS Static BOOTP/RARP DHCP* DLC/LLC Bin PS Auto* PCL PostScript 5 ... 60* ... 300 Seconds NetBEUI Enable NetBEUI PDL NetBEUI Bin PS AppSocket Enable AppSocket PDL AppSocket Bin PS EtherTalk Enable HTTP Enable IP Address Res IP Address1 Sub Net Mask1 Default Gateway1 Port Timeout xxx.xxx.xxx.xxx On* Off Speed2Auto* 10/HALF 10/FULL 100/HALF 100/FULL 1 Appears only if IP Address Res = Static.2 Appears only if 10/100 Ethernet option is installed. On* OffAuto* PCL PostScriptOn Off* On* OffAuto* PCL PostScriptOn Off* On* OffAuto* PCL PostScriptOn Off* On Off* On* Off On* Off Downloaded From ManualsPrinter.com Manuals
Ethernet Menu Chapter 1: Configuring the Printer v1-59 Table 1.15 Ethernet Menu functions Menu Item and FunctionKeystrokesDisplay LPR Enable Enable or disable the Ethernet LPR protocol. The available values are: On* Off 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu LPR Enable 3. Press Va l u e U p or Va l u e D o w n until you see:LPR Enable = New Value 4. Press Enter. You will see:Ethernet Menu LPR Enable 5. Press Online. You will see:Ready LPR Banner Enable or disable the LPR banner sheet. The available values are: On Off* 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu LPR Banner 3. Press Va l u e U p or Va l u e D o w n until you see:LPR Banner = New Value 4. Press Enter. You will see:Ethernet Menu LPR Banner 5. Press Online. You will see:Ready LPR PDL Set the default emulation for the Ethernet LPR protocol. The available values are: Auto* PCL PostScript 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu LPR PDL 3. Press Va l u e U p or Va l u e D o w n until you see:LPR PDL = New Value 4. Press Enter. You will see:Ethernet Menu LPR PDL 5. Press Online. You will see:Ready Table1.15 Page1 of 10 Downloaded From ManualsPrinter.com Manuals
Ethernet Menu 1-60 vDocuPrint NC60 System Administrator Guide LPR Binary PS Enable or disable the LPR binary mode of PostScript. The available values are: On Off* 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu LPR Binary PS 3. Press Va l u e U p or Va l u e D o w n until you see:LPR Binary PS = New Value 4. Press Enter. You will see:Ethernet Menu LPR Binary PS 5. Press Online. You will see:Ready DLC/LLC Enable Enable or disable the DLC/LLC protocol. The available values are: On* Off 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu DLC/LLC Enable 3. Press Va l u e U p or Va l u e D o w n until you see:DLC/LLC Enable = New Value 4. Press Enter. You will see:Ethernet Menu DLC/LLC Enable 5. Press Online. You will see:Ready DLC/LLC PDL Set the default emulation for the DLC/ LLC protocol. The available values are: Auto* PCL PostScript 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu DLC/LLC PDL 3. Press Va l u e U p or Va l u e D o w n until you see:DLC/LLC PDL = New Value 4. Press Enter. You will see:Ethernet Menu DLC/LLC PDL 5. Press Online. You will see:Ready Table 1.15 Ethernet Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.15 Page2 of 10 Downloaded From ManualsPrinter.com Manuals
Ethernet Menu Chapter 1: Configuring the Printer v1-61 DLC/LLC Bin PS Enable or disable the DLC/LLC binary mode of PostScript. The available values are: On Off* 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu DLC/LLC Bin PS 3. Press Va l u e U p or Va l u e D o w n until you see:DLC/LLC Bin PS = New Value 4. Press Enter. You will see:Ethernet Menu DLC/LLC Bin PS 5. Press Online. You will see:Ready NetBEUI Enable Enable or disable the NetBEUI protocol. The available values are: On* Off 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu NetBEUI Enable 3. Press Va l u e U p or Va l u e D o w n until you see:NetBEUI Enable = New Value 4. Press Enter. You will see:Ethernet Menu NetBEUI Enable 5. Press Online. You will see:Ready NetBEUI PDL Set the default emulation for the NetBEUI protocol. The available values are: Auto* PCL PostScript 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu NetBEUI PDL 3. Press Va l u e U p or Va l u e D o w n until you see:NetBEUI PDL = New Value 4. Press Enter. You will see:Ethernet Menu NetBEUI PDL 5. Press Online. You will see:Ready Table 1.15 Ethernet Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.15 Page3 of 10 Downloaded From ManualsPrinter.com Manuals
Ethernet Menu 1-62 vDocuPrint NC60 System Administrator Guide NetBEUI Bin PS Enable or disable the NetBEUI binary mode of PostScript. The available values are: On Off* 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu NetBEUI Bin PS 3. Press Va l u e U p or Va l u e D o w n until you see:NetBEUI Bin PS = New Value 4. Press Enter. You will see:Ethernet Menu NetBEUI Bin PS 5. Press Online. You will see:Ready AppSocket Enable Enable or disable the Ethernet AppSocket protocol. The AppSocket in the printer supports Ports 2000, 9100, and 2501. The available values are: On* Off 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu AppSocket Enabl 3. Press Va l u e U p or Va l u e D o w n until you see:AppSocket Enabl= New Value 4. Press Enter. You will see:Ethernet Menu AppSocket Enabl 5. Press Online. You will see:Ready AppSocket PDL Set the default emulation for the Ethernet AppSocket protocol. The available values are: Auto* PCL PostScript 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu AppSocket PDL 3. Press Va l u e U p or Va l u e D o w n until you see:AppSocket PDL = New Value 4. Press Enter. You will see:Ethernet Menu AppSocket PDL 5. Press Online. You will see:Ready Table 1.15 Ethernet Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.15 Page4 of 10 Downloaded From ManualsPrinter.com Manuals
Ethernet Menu Chapter 1: Configuring the Printer v1-63 AppSocket Bin PS Enable or disable the AppSocket binary mode of PostScript. The available values are: On Off* 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu AppSocket Bin PS 3. Press Va l u e U p or Va l u e D o w n until you see:AppSocket Bin PS= New Value 4. Press Enter. You will see:Ethernet Menu AppSocket Bin PS 5. Press Online. You will see:Ready EtherTalk Enable Enable or disable the Ethernet EtherTalk protocol. The available values are: On* Off 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu EtherTalk Enable 3. Press Va l u e U p or Va l u e D o w n until you see:EtherTalk Enable= New Value 4. Press Enter. You will see:Ethernet Menu EtherTalk Enable 5. Press Online. You will see:Ready HTTP Enable Enable or disable the Ethernet HTTP Server protocol. The available values are: On* Off 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu HTTP Enable 3. Press Va l u e U p or Va l u e D o w n until you see:HTTP Enable = New Value 4. Press Enter. You will see:Ethernet Menu HTTP Enable 5. Press Online. You will see:Ready Table 1.15 Ethernet Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.15 Page5 of 10 Downloaded From ManualsPrinter.com Manuals
Ethernet Menu 1-64 vDocuPrint NC60 System Administrator Guide IP Address Res. Set the method used to assign the IP address, including subnet mask and default gateway. The available values are: Static BOOTP/RARP DHCP* 1. Press Menu Up or Menu Down until you see:Menus Ethernet Menu 2. Press Item Up or Item Down until you see:Ethernet Menu IP Address Res. 3. Press Va l u e U p or Va l u e D o w n until you see:IP Address Res.= New Value 4. Press Enter. You will see:Ethernet Menu IP Address Res. 5. Press Online. You will see:Ready Table 1.15 Ethernet Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.15 Page6 of 10 Downloaded From ManualsPrinter.com Manuals