Xerox DocuPrint 255DN User Manual
Have a look at the manual Xerox DocuPrint 255DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 228 Xerox manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Print Menu Chapter 1: Configuring the Printer v1-95 Disk Directory Print a list of fonts and macros downloaded to the hard disk. This procedure does not list any secure or proof jobs.1. Press Menu Up or Menu Down until you see: Menus Print Menu 2. Press Item Up or Item Down until you see:Print Menu Disk Directory 3. Press Enter. You will see:Printing Disk Directory 4. When completed, you will see:Ready Print Quantity Set the number of times each page is printed. The available values are: 1* - 999 The quantity changes incrementally by 1 each time either Va l u e U p or Va l u e D o w n is pressed. Holding down Va l u e U p or Va l u e D o w n causes continuous scrolling through the values.1. Press Menu Up or Menu Down until you see: Menus Print Menu 2. Press Item Up or Item Down until you see:Print Menu Print Quantity 3. Press Va l u e U p or Va l u e D o w n until you see:Print Quantity = New Value 4. Press Enter. You will see:Print Menu Print Quantity 5. Press Online. You will see:Ready Select Tray Select the source tray from which the job is to be printed. The available values are: Tr a y 1 * Tr a y 2 Manual Feeder Appears and is a choice only when the optional Tray 2 is installed. The Tray Sequence setting is ignored. Media size or type mismatches will be handled via the current Page Policy settings.1. Press Menu Up or Menu Down until you see: Menus Print Menu 2. Press Item Up or Item Down until you see:Print Menu Select Tray 3. Press Va l u e U p or Va l u e D o w n until you see:Select Tray = New Value 4. Press Enter. You will see:Print Menu Select Tray 5. Press Online. You will see:Ready Table 1.18 Print Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.18 Page4 of 4 Downloaded From ManualsPrinter.com Manuals
Media Server Menu 1-96 vDocuPrint NC60 System Administrator Guide Media Server Menu Use the Media Server Menu to print from the Media Server. The menu hierarchy is shown in Figure 1.15. Refer to Table 1.19 on page 1-97 for step-by-step instructions. Figure 1.15 Media Server Menu hierarchy with factory settings Select File Tr a y 1 * Tr a y 2 Manual Feeder Print Quantity Select Tray Job Menu Password Menu Tr a y M e n u PCL Menu System Menu Color Adjust Menu Imaging Menu Parallel Menu Serial Menu Ethernet Menu Token Ring Menu Novell Menu Print Menu Media Server Menu Service Menu Reset Menu 1* - 999 Filename n . . Filename 1* Downloaded From ManualsPrinter.com Manuals
Media Server Menu Chapter 1: Configuring the Printer v1-97 Table 1.19 Media Server Menu functions Menu Item and FunctionKeystrokesDisplay Select File Select a file from the Media Server’s floppy disk. The available values are: Filename 1 through Filename n Value keys scroll through floppy filenames to find selection.1. Press Menu Up or Menu Down until you see: Menus Media Server Menu 2. Press Item Up or Item Down until you see:Media Server Menu Select File 3. Press Va l u e U p or Va l u e D o w n until you see:Select File = Filename 4. Press Enter. You will see:Printing Filename 5. When completed, you will see:Ready Print Quantity Set the number of times each page is printed. The available values are: 1* - 999 The quantity changes incrementally by 1 each time either Va l u e U p or Va l u e D o w n is pressed. Holding down Va l u e U p or Va l u e D o w n causes continuous scrolling through the values. This value is used rather than the value in the print file.1. Press Menu Up or Menu Down until you see: Menus Media Server Menu 2. Press Item Up or Item Down until you see:Media Server Menu Print Quantity 3. Press Va l u e U p or Va l u e D o w n until you see:Print Quantity = New Value 4. Press Enter. You will see:Media Server Menu Print Quantity 5. Press Online. You will see:Ready Table1.19 Page1 of 2 Downloaded From ManualsPrinter.com Manuals
Media Server Menu 1-98 vDocuPrint NC60 System Administrator Guide Select Tray Select the source tray from which the job is to be printed. The available values are: Tr a y 1 * Tr a y 2 Manual Feeder Appears and is a choice only when the optional Tray 2 is installed. The Tray Sequence setting is ignored. Media size or type mismatches will be handled via the current Page Policy settings. This tray selection is used rather than the selection in the print file.1. Press Menu Up or Menu Down until you see: Menus Media Server Menu 2. Press Item Up or Item Down until you see:Media Server Menu Select Tray 3. Press Va l u e U p or Va l u e D o w n until you see:Select Tray = New Value 4. Press Enter. You will see:Media Server Menu Select Tray 5. Press Online. You will see:Ready Table 1.19 Media Server Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.19 Page2 of 2 Downloaded From ManualsPrinter.com Manuals
Service Menu Chapter 1: Configuring the Printer v1-99 Service Menu Use the Service Menu to generate printer reports and set service options. The menu hierarchy is shown in Figure 1.16 on page 1-100. Refer to Table 1.20 on page 1-101 for step-by-step instructions. Downloaded From ManualsPrinter.com Manuals
Service Menu 1-100 vDocuPrint NC60 System Administrator Guide Figure 1.16 Service Menu hierarchy Config Sheet Te s t P a t t e r n s Job Menu Password Menu Tr a y M e n u PCL Menu System Menu Color Adjust Menu Imaging Menu Parallel Menu Serial Menu Ethernet Menu Token Ring Menu Novell Menu Print Menu Media Server Menu Service Menu Reset Menu OHP Mode Print PQ Set Select Tray Print Quantity Diag. Summary 100% Stripe Black Step Blank Color Balance Cyan Step Gray Halftone Mag Step Pattern A Ye l lo w St e p PCL Pattern IOT Pattern Auto* Tray 1 Tray 2 Margin Left Margin Top Cleaning Cycle Patch Control Show Page Counts Show SetpointsOn Off* CRU Usage Lossy Counter Faults Active Fault History S/W Levels None 1,2,3,4 Default* To t a l C o u n t Black Count Cyan Count Magenta Count Ye l lo w C o u n t Black Dev. Cart Color Dev. Cart Fuser Module % Print Drum % 1* - 999 -5 .. 0* .. 10.0 mm -3 .. 0* .. 10.0 mm 100 Images 90 Images 80 Images 70 Images 60 Images 50 Images 40 Images 30 Images 20 Images* 10 Images Never Black TC Cyan TC Magenta TC Yellow TC Binary 1200 Quality “Highest Fault” . . “Lowest Fault” “50th Fault” . . “Last Fault” Adobe PostScrip Boot Controller IOT Downloaded From ManualsPrinter.com Manuals
Service Menu Chapter 1: Configuring the Printer v1-101 Table 1.20 Service Menu functions Menu Item and FunctionKeystrokesDisplay Config Sheet Print a Configuration Sheet showing the printers current information and menu settings. The Configuration Sheet is formatted for either Letter or A4 paper size, regardless of the default paper size or the actual paper size loaded.1. Press Menu Up or Menu Down until you see:Menus Service Menu 2. Press Item Up or Item Down until you see:Service Menu Config Sheet 3. Press Enter. You will see:Printing Config Sheet 4. When completed, you will see:Ready Diag. Summary Print the current diagnostic summary data. Source tray is determined by the Select Tray item. The Diagnostic Summary Sheet(s) are formatted for either Letter or A4 paper size, regardless of the default paper size or the actual paper size loaded. There are no multiple copies.1. Press Menu Up or Menu Down until you see:Menus Service Menu 2. Press Item Up or Item Down until you see:Service Menu Diag. Summary 3. Press Enter. You will see:Service Menu Diag. Summary 4. When completed, you will see:Ready Print PQ Set Print the PQ set: one “Test Pattern A,” one “Color Balance” pattern and one “Diagnostic Page” in PS. The PQ set is formatted for either Letter or A4 paper size, regardless of the default paper size or the actual paper size loaded. There are no multiple copies. The Print Quantity value is ignored. Source tray is determined by the Select Tray value.1. Press Menu Up or Menu Down until you see:Menus Service Menu 2. Press Item Up or Item Down until you see:Service Menu Print PQ Set 3. Press Enter. You will see:Service Menu Print PQ Set 4. When completed, you will see:Ready Table1.20 Page1 of 8 Downloaded From ManualsPrinter.com Manuals
Service Menu 1-102 vDocuPrint NC60 System Administrator Guide Test Patterns Enable printing of printer resident, PostScript test patterns. The available values are: 100% Stripe Mag Step Black Step Pattern A Blank Yellow Step Color Balance PCL Pattern Cyan Step IOT Pattern Gray Halftone Patterns are formatted for either Letter or A4 paper size, regardless of the default paper size or the actual paper size loaded.1. Press Menu Up or Menu Down until you see: Menus Service Menu 2. Press Item Up or Item Down until you see:Service Menu Test Patterns 3. Press Va l u e U p or Va l u e D o w n until you see:Test Patterns = New Value 4. Press Enter. You will see:Service Menu Test Patterns 5. Press Online. You will see:Ready Print Quantity Set the number of times each page is printed (uncollated). The available values are: 1* .. 999 The number of copies changes incrementally by 1 each time either Va l u e U p or Va l u e D o w n is pressed. Holding down Va l u e U p or Va l u e Down causes continuous scrolling through the number of copies.1. Press Menu Up or Menu Down until you see: Menus Service Menu 2. Press Item Up or Item Down until you see:Service Menu Print Quantity 3. Press Va l u e U p or Va l u e D o w n until you see:Print Quantity = New Value 4. Press Enter. You will see:Service Menu Print Quantity 5. Press Online. You will see:Ready Table 1.20 Service Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.20 Page2 of 8 Downloaded From ManualsPrinter.com Manuals
Service Menu Chapter 1: Configuring the Printer v1-103 OHP Mode Set Overhead Projection mode to allow discrete selection of settings for fuser temperature and transfer bias voltages to enhance the performance for transparencies. The available values are: None 1,2,3,4 Default* 1. Press Menu Up or Menu Down until you see:Menus Service Menu 2. Press Item Up or Item Down until you see:Service Menu OHP Mode 3. Press Va l u e U p or Va l u e D o w n until you see:OHP Mode = New Value 4. Press Enter. You will see:Service Menu OHP Mode 5. Press Online. You will see:Ready Select Tray Select the source tray from which the job is to be printed. The available values are: Tr a y 1 * Tray 2 Manual Feeder Appears and is a choice only when the optional Tray 2 is installed. The Tray Sequence setting is ignored. Job to media size or type mismatch will be handled via the current Page Policy settings.1. Press Menu Up or Menu Down until you see: Menus Service Menu 2. Press Item Up or Item Down until you see:Service Menu Select Tray 3. Press Va l u e U p or Va l u e D o w n until you see:Select Tray = New Value 4. Press Enter. You will see:Service Menu Select Tray 5. Press Online. You will see:Ready Table 1.20 Service Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.20 Page3 of 8 Downloaded From ManualsPrinter.com Manuals
Service Menu 1-104 vDocuPrint NC60 System Administrator Guide Margin Left Set the left margin or horizontal displacement of the logical printed page versus the physical page. The available values are: -5 .. 0* .. 10.0 mm A negative value moves the logical printed page (area) “left” on the physical page.1. Press Menu Up or Menu Down until you see: Menus Service Menu 2. Press Item Up or Item Down until you see:Service Menu Margin Left 3. Press Va l u e U p or Va l u e D o w n until you see:Margin Left = New Value 4. Press Enter. You will see:Service Menu Margin Left 5. Press Online. You will see:Ready Margin Top Set the top margin or vertical displacement of the logical printed page versus the physical page. The available values are: -3 .. 0* .. 10.0 mm A negative value moves the logical printed page (area) “up” the physical page.1. Press Menu Up or Menu Down until you see: Menus Service Menu 2. Press Item Up or Item Down until you see:Service Menu Margin Top 3. Press Va l u e U p or Va l u e D o w n until you see:Margin Top = New Value 4. Press Enter. You will see:Service Menu Margin Top 5. Press Online. You will see:Ready Table 1.20 Service Menu functions (continued) Menu Item and FunctionKeystrokesDisplay Table1.20 Page4 of 8 Downloaded From ManualsPrinter.com Manuals